Postoperative TPA

Both triceps tendons and the medial collateral ligaments of both stifles of 10 freshly euthanized dogs were sharply transected. One tendon and one ligament of each dog were sutured with a three loop pulley pattern, and the opposite tendons and ligaments were sutured with a locking loop pattern. The tendons and ligaments were harvested with their muscular and bony attachments. The anastomoses were slowly tested in tension until failure occurred. The amount of tensile load required to produce failure of the anastomosis, the amount of distraction of the sutured ends prior to failure, and the modes of failure were recorded. In both tendons and ligaments, the three loop pulley pattern provided significantly greater tensile strength (p < 0.01) and allowed significantly less distraction between the sutured ends (p < 0.01) than the locking loop pattern. In tendons, disruption of the suture material was the most common mode of failure with both patterns. In ligaments, both patterns failed most commonly by pulling free from the tissue.

Achilles' ruptures repaired with suture can be augmented with mesh to increase the ultimate load to failure, but as currently tested, there was a decrease in resistance to gap formation At this time we cannot recommend Mesh or the Suture+Mesh techniques without further testing.

Results suggested that early neutering was a significant risk factor for development of excessive TPA in large-breed dogs with CCLD. Further research into the effects of early neutering on TPA and the pathophysiology of CCLD is warranted.

The purpose of this study was to determine the respective contribution of each of the following parameters to the compressive, bending, and torsional rigidity of the Kirschner-Ehmer (KE) external fixation splint as applied to canine tibiae with an osteotomy gap: bilateral versus unilateral splints; increasing the number of fixation pins; altering the diameter of fixation pins and side bars; decreasing side bar distances from the bone; increasing pin separation distances in each pin group; decreasing distances between pin groups; altering pin clamp orientation; and altering side bar conformation. Bilateral splints were 100% (mean) stiffer than unilateral splints, with stiffness enhanced to the greatest extent in mediolateral bending and torsion. Increasing pin numbers stiffened both bilateral (mean, 41%; 8 versus 4) and unilateral splints (mean, 14%; 8 versus 4). Medium KE splints were 85% (mean) stiffer than small KE splints. Decreasing side bar distances to the bone from 1.5 cm to 1.0 cm to 0.5 cm increased stiffness of both bilateral and unilateral splints by a mean of 13% to 35%. Widening pin spacing from 1.67 cm to 2.5 cm increased stiffness in craniocaudal bending only (56% increase, bilateral splints; 73% increase, unilateral splints). Decreasing the distance between pin groups from 5.84 cm to 2.5 cm increased stiffness in torsion between 23% (unilateral splints) and 45% (bilateral splints) and decreased stiffness of unilateral splints by 29% in craniocaudal bending. Altering pin clamp configuration so that the bolts of the clamp were inside the side bar rather than outside the side bar increased stiffness in axial compression only (73% increase, bilateral splints; 54% increase, unilateral splints). Conforming the lateral side bar to the tibiae increased only axial compressive stiffness by 77% but was no different than placing the clamps inside the side bars of an unconformed bilateral splint. These results quantify the relative importance of specific parameters affecting KE splint rigidity as applied to unstable fractures in the dog.

Knotting method does influence the structural properties of suture materials and should be considered when tying knots under tension.

The relative strength of six different configurations of external skeletal fixation was determined by subjecting them to axial compression, and shear and torsion forces while measuring the load they would sustain before failing. The double clamp, single connecting bar, double connecting bar, quadrilateral frame, full pin splintage and three‐ dimensional tent configurations were found to be successively stronger in all three of the tests with the exception of the quadrilateral frame being more resistant to shear force than the full pin splintage configuration.

Smooth and partially threaded 3.12 mm (W inch) trochar-tipped Steinmann pins were inserted transversely through both diaphyseal cortices of eight mature canine tibias using five methods. Angular velocity (revolutions per minute) during insertion and temperature elevation due to friction during penetration of the second cortex were recorded. The force required for extraction of the pins from the bone and the histologic appearance of the bone-pin interface were determined for one-half of the pins 2 days after insertion and for one-half of the pins 56 days after insertion. The increase in temperature was similar for all methods of insertion except high speed power, which was significantly greater (p < 0.05). The force required for axial pin extraction was similar for pins inserted by hand chuck, predrllled, and low speed power methods after both 2 and 56 days. Pins inserted by high speed power and hand drill required force similar to the others for extraction after 2 days but significantly less force (p < 0.05) for extraction after 56 days. The partially threaded pins required significantly greater force (p < 0.01) extraction after both 2 and 56 days. Hlstologic examination revealed increased mechanical bone damage surrounding hand chuck inserted pins, increased bone necrosis surrounding high speed power inserted pins, and increased inflammatory changes surrounding hand drill inserted pins.