No other resource is as necessary for life as water, and providing it universally in a safe, reliable and affordable manner is one of the greatest challenges of the twenty-first century. Here, we consider new opportunities and approaches for the application of nanotechnology to enhance the efficiency and affordability of water treatment and wastewater reuse. Potential development and implementation barriers are discussed along with research needs to overcome them and enhance water security.
This paper presents 3D printing of piezoelectric sensors using BaTiO3 (BTO) filler in a poly(vinylidene) fluoride (PVDF) matrix through electric in situ poling during the 3D printing process. Several conventional methods require complicated and time‐consuming procedures. Recently developed electric poling‐assisted additive manufacturing (EPAM) process paves the way for printing of piezoelectric filaments by incorporating polarizing processes that include mechanical stretching, heat press, and electric field poling simultaneously. However, this process is limited to fabrication of a single PVDF layer and quantitative material characterizations such as piezoelectric coefficient and β‐phase percentage are not investigated. In this paper, an enhanced EPAM process is proposed that applies a higher electric field during 3D printing. To further increase piezoelectric response, BTO ceramic filler is used in the PVDF matrix. It is found that a 55.91% PVDF β‐phase content is nucleated at 15 wt% of BTO. The output current and β‐phase content gradually increase as the BTO weight percentage increases. Scanning electron microscopy analysis demonstrates that larger agglomerates are formulated as the increase of BTO filler contents and results in increase of toughness and decrease of tensile strength. The highest fatigue strength is observed at 3 wt% BTO and the fatigue strength gradually decreases as the BTO filler contents increases.
Reactions of Mo(2)(O(2)CCH(3))(DAniF)(3), DAniF = N,N'-di-p-anisylformamidinate, with oxamidate dianions [ArNC(O)C(O)NAr](2-), Ar = C(6)H(5) and p-anisyl, give pairs of isomeric compounds where the [Mo(2)] units are bridged by the oxamidate anions. For the alpha isomers, the C-C unit of the dianion is nearly perpendicular to the Mo-Mo bonds, and these are essentially perpendicular to each other. For the beta isomers, the corresponding C-C unit and the Mo-Mo bonds are essentially parallel to each other. Each type of isomer is stable in solution. The electronic communication as measured by the DeltaE(1/2) for the oxidation of each of the Mo(2) units is significantly better for the beta isomers. This is supported also by the appearance of what is conventionally called an intervalence charge-transfer band in the near infrared region upon oxidation of the beta isomers but not the alpha isomers. Molecular mechanics and DFT calculations help explain the relative conformations in the alpha isomers and the relative energy differences between the alpha and beta isomers.
Hybrid nanocomposites based on Cu-BTC MOF, graphene oxide (GO), carbon nanotubes (CNTs), and Fe3O4 magnetic nanoparticles (MNPs) were developed via a simple green solvothermal method, at which GO and CNT were used as platforms to load nanostructured Cu-BTC MOF and Fe3O4 MNPs. The as-synthesized hybrid nanocomposites were characterized by XRD, SEM, TEM, XPS, IR, Raman, TGA, and BET techniques. XRD measurements show highly crystalline structures for the prepared hybrid nanocomposites. Morphological analyses carried out by SEM and TEM also confirm successful growth of Fe3O4 MNPs and nanoparticulate Cu-BTC MOF over the carbon-based platforms. Chemical, elemental, and TGA analyses verify chemical bonding and successful compositing of the parent materials. Nitrogen isotherms show a cumulative pore volume of 0.360 cm 3 g-1 for the hybrid nanocomposite of Fe3O4/Cu-BTC@GO compared to 0.030 cm 3 g-1 of the sole Cu-BTC MOF, which suggests potential uses towards small molecule adsorption. We have found that use of GO and CNT substrates (i) diminish the aggregation and increases dispersive forces within the MOFs, (ii) lead to MOFs with different morphology and size, and (iii) result in formation of small pores between the MOF and the platforms. Adsorption capacity of the prepared nanomaterials was examined over methylene blue (MB) as a model organic pollutant. The developed hybrid nanomaterials show enhanced pollutant adsorption capacity compared to that of the parent materials. The improved adsorption capacity is attributed to the synergetic effect of covalent bonding between the parent materials as well as to the unique features of the nanoscale MOF. Overall, these novel materials may be considered as excellent candidates towards a variety of environmental applications such as water remediation.
This paper presents a novel process to fabricate piezoelectric films from polyvinylidene fluoride (PVDF) polymer using integrated fused deposition modeling (FDM) 3D printing and corona poling technique. Corona poling is one of many effective poling processes that has received attention to activate PVDF as a piezoelectric responsive material. The corona poling process occurs when a PVDF polymer is exposed to a high electric field created and controlled through an electrically charged needle and a grid electrode under heating environment. FDM 3D printing has seen extensive progress in fabricating thermoplastic materials and structures, including PVDF. However, post processing techniques such as poling is needed to align the dipoles in order to gain piezoelectric properties. To further simplify the piezoelectric sensors and structures fabrication process, this paper proposes an integrated 3D printing process with corona poling to fabricate piezoelectric PVDF sensors without post poling process. This proposed process, named ‘Integrated 3D Printing and Corona poling process’ (IPC), uses the 3D printer’s nozzle and heating bed as anode and cathode, respectively, to create poling electric fields in a controlled heating environment. The nozzle travels along the programmed path with fixed distance between nozzle tip and sample’s top surface. Simultaneously, the electric field between the nozzle and bottom heating pad promotes the alignment of dipole moment of PVDF molecular chains. The crystalline phase transformation and output current generated by printed samples under different electric fields in this process were characterized by a Fourier transform infrared spectroscopy and through fatigue load frame. It is demonstrated that piezoelectric PVDF films with enhanced β-phase percentage can be fabricated using the IPC process. In addition, mechanical properties of printed PVDF was investigated by tensile testing. It is expected to expand the use of additive manufacturing to fabricate piezoelectric PVDF-based devices for applications such as sensing and energy harvesting.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.