We propose the use of aluminum nitride (AlN) membranes acting as sensitive elements for the surface acoustic wave (SAW)-based acceleration measurement. The proposed solution is compared against existing prototypes based on the use of quartz (SiO2)/lithium niobate (LiNbO3) membranes that are characterized by extensive anisotropic properties. Using COMSOL Multiphysics 5.4 computer simulations we show explicitly that sensitive elements based on less anisotropic AlN membranes overcome both the low sensitivity limitations of SiO2 and low temperature stability of LiNbO3. Moreover, AlN membranes exhibit nearly double the robustness against irreversible mechanical deformations when compared against SiO2, which in turn allows for further 1.5-fold sensitivity enhancement over LiNbO3 based sensors. Taking into account their acceptable frequency characteristics, we thus believe that the AlN membranes are a good candidate forsensitive elements especially for high acceleration measurements.
Recently, we proposed a ring-shaped surface acoustic wave (SAW) resonator sensitive element design, as well as analyzed its characteristics and suggested its optimization strategy, with major focus on their temperature stability. Here, we focus on further optimization of the design to narrow the bandwidth and improve signal detection, while taking into account typical technological limitations. Additionally, the purpose of design optimization and modeling is to check the preservation of operability in the case of lithography defects, which is the most common technological error. For that, we suggest structural alteration of the interdigital transducer (IDT) that leads to its partial fragmentation. Using COMSOL Multiphysics computer simulations, we validate several IDT options and show explicitly how it could be optimized by changing its pin geometry. Based on the results of the study, prototyping and printing of ring resonators on a substrate using photolithography will be carried out.
Originally, sensors based on surface acoustic waves are fabricated using photolithography, which becomes extremely expensive when a small series or even single elements are needed for the research. A laser thin film local evaporation technique is proposed to substitute the photolithography process in the production of surface acoustic wave based inertial sensors prototypes. To estimate its potential a prototype of a surface acoustic wave gyroscope sensing element was fabricated and tested. Its was shown that the frequency mismatch is no more than 1%, but dispersion of the wave on small inertial masses leads to a spurious parasitic signal on receiving electrodes. Possible ways of its neglecting is discussed.
Introduction. At the present, sensors based on surface acoustic waves (SAW) is a rapidly developing direction and a promising replacement for classical sensors, especially in those areas where long-term performance of latter is questionable. The principle of operation of SAW sensors is based on acoustic vibrations, therefore, the choice of piezoelectric material of а console, considering external influences on a future device and its operating conditions, is the most important task. Currently, many monocrystalline structures and their sections have been synthesized and created for the devices using SAW. The main materials used for the manufacture of substrates are crystals of quartz (SiO2), lithium niobate (LiNbO3), lithium tantalate (LiTaO3) and film aluminum nitride (AlN). Also, new crystal structures: langasite (La3Ga5SiO14), langatate (La3Ga5.5Ta0.5O14), langanite and others were produced. The problem of using such materials for the manufacture of consoles is the lack of systematized data on important characteristics for the propagation of surfactants, for example, the elasticity tensor of the 4th rank. One of the key problems for the further development of SAW-based sensors is the one-way fastening of rectangular and triangular sensitive elements (SE) in sensor housing. In order to overcome the above drawback an MMA surfactant thing based on a membrane SE for a more uniform distribution of a load over the surface of the SE was proposed.Aim. To show the advantages of using AlN as the SE material of a ring wave resonator on SAW.Materials and methods. The theoretical part of the research was carried out using the finite element method. Mathematical processing was implemented in AutoCAD 2019 and in COMSOL Multiphysics 5.4.Results. The use of AlN, which acts as the SE material for measuring an acceleration based on SAW was proposed. The proposed solution was compared with existing prototypes based on the use of SiO2 / LiNbO3 membranes, which were characterized by strong anisotropic properties. A 3D model of the SE of a ring wave resonator on surface waves was created. Using computer simulations and COMSOL Multiphysics software, it was shown that the thing was capable to withstand exposures in excess of 10 000 g, and an isotropic AlN sensor overcomed the limitations of both the low sensitivity of SiO2 and the low temperature stability of LiNbO3. AlN demonstrated almost double resistance to irreversible mechanical deformations as compared to SiO2, which, in turn, allows an additional 1.5-fold increase in sensitivity compared to quartz – based sensors.Conclusion. Based on the data obtained by the modeling, it can be concluded that the use of AIN as SE material is promising, especially for measuring high acceleration values, but with restrictions on temperature sensitivity of the material.
Introduction. Previous works considered the frequency characteristics and methods for fixing sensitive elements in the form of a wave ring resonator on surface acoustic waves in a housing made of various materials, as well as the influence of external factors on sensitive elements. It was found that the passband in such a case is sufficiently wide, which can affect adversely signal detection when measuring acceleration using the sensitive element under development. Therefore, it has become relevant to reduce the sensitive element’s bandwidth by changing the design of the interdigitated transducer (IDT).Aim. To demonstrate an optimal topology for an IDT with a low bandwidth, leading to improved signal detection when acceleration affects the sensitive element.Materials and methods. The finite element method and mathematical processing in AutoCAD and in COMSOL Multiphysics.Results. Nine topologies of IDT are proposed. All these types were investigated using the COMSOL Multiphysics software on lithium niobate substrates, which material acts as a sensitive element. The frequency characteristics are presented. The data obtained allowed an optimal design of the ring resonator to be proposed: an IDT with rectangular pins without selective withdrawal.Conclusion. Self-generation in a ring resonator can be performed by withdrawing no more than one pair of IDTs for 10 or more periods. In this case, the withdrawal of IDTs should be uniform. With an increase in the number of IDT withdrawals, the geometry of the ring resonator is violated, and the wave leaves the structure. The presence of a shared bus keeps the surface acoustic wave inside the IDT structure, and the narrowing of the periods towards the inner part of the structure makes it possible to improve the frequency characteristics of the ring resonator on surface acoustic waves.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.