During the past two decades, the use of ambient vibrations for modal analysis of structures has increased as compared to the traditional techniques (forced vibrations). The Frequency Domain Decomposition method is nowadays widely used in modal analysis because of its accuracy and simplicity. In this paper, we first present the physical meaning of the FDD method to estimate the modal parameters. We discuss then the process used for the evaluation of the building stiffness deduced from the modal shapes. The models considered here are 1D lumped-mass beams and especially the shear beam. The analytical solution of the equations of motion makes it possible to simulate the motion due to a weak to moderate earthquake and then the inter-storey drift knowing only the modal parameters (modal model). This process is finally applied to a 9-storey reinforced concrete (RC) dwelling in Grenoble (France). We successfully compared the building motion for an artificial ground motion deduced from the model estimated using ambient vibrations and recorded in the building. The stiffness of each storey and the inter-storey drift were also calculated.

In countries with a moderate seismic hazard, the classical methods developed for strong motion prone countries to estimate the seismic behaviour and subsequent vulnerability of existing buildings are often inadequate and not financially realistic. The main goals of this paper are to show how the modal analysis can contribute to the understanding of the seismic building response and the good relevancy of a modal model based on ambient vibrations for estimating the structural deformation under moderate earthquakes. We describe the application of an enhanced modal analysis technique (Frequency Domain Decomposition) to process ambient vibration recordings taken at the Grenoble City Hall building (France). The frequencies of ambient vibrations are compared with those of weak earthquakes recorded by the French permanent accelerometric network (RAP) that was installed to monitor the building. The frequency variations of the building under moderate earthquakes are shown to be slight (~2%) and therefore ambient vibration frequencies are relevant over the elastic domain of the building. The modal parameters extracted from ambient vibrations are then used to determine the 1D lumped-mass model in order to reproduce the inter-storey drift under weak earthquakes and to fix a 3D numerical model that could be used for strong earthquakes. The correlation coefficients between data and synthetic motion are close to 80% and 90% in horizontal directions, for the 1D and 3D modelling, respectively.

No abstract

No abstract

International audienc

International audienceElastic fundamental frequency is a key-parameter of simplified seismic design and vulnerability assessment methods. Empirical relationships exist in codes to estimate this frequency but they miss experimental data to validate them accounting for national feature of building design and, above all, corresponding uncertainties. Even if resonance frequency extracted from ambient vibrations may be larger than the elastic frequency (at yield) generally used in earthquake engineering, ambient vibration recordings may provide a large set of data for statistical analysis of periods versus building characteristics relationships. We recorded ambient vibrations and estimated the fundamental frequency of about 60 buildings of various types (RC and masonry) in Grenoble City (France). These data complete the set existing yet, made of 26 RC-buildings of Grenoble (Farsi and Bard 2004) and 28 buildings in Nice (France) (Dunand 2005). Statistical analysis of these experimental data was performed for fundamental frequencies of RC shear wall structures and the results are compared with existing relationships. Only building height or number of stories has a statistical relevancy to estimate the resonance frequency but the variability associated to the proposed relationships is large. Moreover, we compared the elastic part of capacity curves of RC and masonry buildings used in the European Risk-UE method for vulnerability assessment with the experimental frequencies. The variability is also large and the curves may not be consistent with French existing buildings

We performed modal analysis using frequency domain decomposition of ambient seismic vibration data collected on large rock slope instabilities. This technique enables a robust detection of resonance frequencies and provides the corresponding mode shape vectors. We applied the technique to synthetic and field data sets acquired by seismometer arrays on two rock instabilities in Switzerland. We found that, at the fundamental mode, the entire instability vibrates in‐phase with the dominant mode shape vector oriented perpendicular to dominant fracture systems. At higher frequencies, different compartments of the instability resonate antiphase. Therefore, delineating the zero crossings between the phases allows dominant fractures to be efficiently mapped. Approximately 1 hr of ambient vibration data suffices to apply the method successfully. The method also potentially detects hidden fractures that cannot be observed by geological field mapping. In addition, this approach combines classic amplification and polarization analysis into one technique, simplifying data processing efforts.

International audienceThe aim of this paper is to adjust behaviour models for each class of structure for vulnerability assessment by using ambient vibration. A simple model based on frequencies, mode shapes and damping, taken from ambient vibrations, allows computation of the response of the structures and comparison of inter-storey drifts with the limits found in the literature for the slight damage grade, considered here as the limit of elastic behaviour. Two complete methodologies for building fragility curves are proposed: (1) using a multi-degree of freedom system including higher modes and full seismic ground motion, (2) using a single-degree of freedom model considering the fundamental mode f0 of the structure and ground motion displacement response spectra SD(f0). These two methods were applied to the city of Grenoble, where 60 buildings were studied. Fragility curves for slight damage were derived for the various masonry and reinforced concrete classes of buildings. A site-specific earthquake scenario, taking into account local site conditions, was considered, corresponding to an ML=5.5 earthquake at a distance of 15km. The results show the benefits of using experimental models to reduce variability of the slight damage fragility curve. Moreover, by introducing the experimental modal model of the buildings, it is possible to improve seismic risk assessment at an overall scale (the city) or a local scale (the building) for the first damage grade (slight damage). This level of damage, of great interest for moderate seismic prone regions, may contribute to the seismic loss assessment