Effect of Stainless Steel Weld Overlay Deposit on the Hardness of API 5L Pipes

Aryswan, Adhe; Arifin, Nurul Laili; Widiastuti, Hanifah; Kirana, Dois Ditya Wahyu

doi:10.5220/0010352801190123

Cited by 3 publications

(2 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Selain ketahanan korosi yang penting pada komponen pulley adalah sifat mekanik yang terkait dengan kekerasan material [11] . Hal ini bertujuan agar sistem pulley mampu memberikan dukungan pada sistem transmisi kendaraan dalam melakukan transfer tenaga dari mesin ke roda kendaraan [12] . Pengukuran nilai kekerasan untuk material jenis stainless steel adalah menggunakan metode bilangan kekerasan Vickers atau Hardness Vickers (HV) sesuai standar ASTM 6507 [13] seperti ditunjukan Gambar 1.…”

Section: Pendahuluanunclassified

Analisa Distribusi Kekerasan Komponen Movable Pulley Driven (Mpdn) Pada Transmisi Kendaraan

Suriaman,

Makki,

Jatira

et al. 2023

JRM

View full text Add to dashboard Cite

Transmission on the vehicle is very important component to ensure maximum power transfer from the engine to the wheels. The speed of four-wheeled vehicles is influenced by the transmission system used. Pulley is the component of continuous variable transmission (CVT) which is currently widely used in the automotive industry. The CVT transmission is type of automatic transmission with gearshift process that does not use gears, but uses pulley. The pulley is made of stainless steel. For CVT transmission there are two pulleys, both of which are called driven pulleys. The CVT transmission shift operation is controlled electronically from the computer to drive the two pulleys. These two pulleys can move to the right or to the left, respectively, so that the width of the two pulleys can change to narrow or widen. The drive pulley moves away so the belt will move inward and the same time the driven pulley will narrow so the belt will move further out. The pulley diameter becomes the gear ratio in a CVT transmission. In the CVT transmission process there will be friction between the two surfaces of the pulley and the belt, therefore it is necessary to measure the hardness of the material from the pulley to ensure the vehicle's transmission capability. In this study, the hardness of the pulley material was measured using a Vickers machine according to the ASTM 6507 standard with a given load of 0.3 kg. The measurement results obtained an average value of hardness Vickers (HV) for the pulley material of 473.

show abstract

Section: Pendahuluanunclassified

Analisa Distribusi Kekerasan Komponen Movable Pulley Driven (Mpdn) Pada Transmisi Kendaraan

Suriaman,

Makki,

Jatira

et al. 2023

JRM

View full text Add to dashboard Cite

show abstract

“…Austenitic stainless steels (SS 316L and SS 304) are commonly used in corrosive environments due to their corrosion resistance, weldability, and mechanical strength. One of the methods used to provide long-term protection against corrosion, wear, and erosion by calculating cost-effectiveness is overlay welding [5]- [8].…”

Section: Introductionmentioning

confidence: 99%

Overlay welding analysis on GTAW and SMAW processes in terms of mechanical properties and corrosion rate

Fikrie

Pratiwi²,

Fakhri

2022

JEATech

View full text Add to dashboard Cite

The Overlay welding process is a coating technique that is carried out using the welding process. In this study, a coating was conducted on carbon SA 516 gr. 70 with stainless steel electrodes. Welding was carried out with the GTAW and SMAW processes. The electrode used in the first coating for GTAW was ER309L while for SMAW was E309L. The next coating used in the GTAW electrode was ER316L and the SMAW electrode was E316L. In both welding processes, testing was carried out on mechanical properties and corrosion rates. Testing was carried out to determine mechanical properties, namely bending testing. This was done based on ASME IX. Bending test results in both processes are declared accepted because there are no defects. In testing the corrosion rate using the three-electrode cell method based on the ASTM G102 Overlay welding process with GTAW has a slower corrosion rate of 0.00890 MMPY compared to the overlay welding process with SMAW.

show abstract

Experimental Investigation on Stainless-Steel Weld Overlay on Carbon Steel Plates Using Different Electrodes

Saffiudeen,

Swaminathan,

Mohammed

et al. 2024

Arab J Sci Eng

View full text Add to dashboard Cite

Effect of Stainless Steel Weld Overlay Deposit on the Hardness of API 5L Pipes

Cited by 3 publications

References 0 publications

Analisa Distribusi Kekerasan Komponen Movable Pulley Driven (Mpdn) Pada Transmisi Kendaraan

Analisa Distribusi Kekerasan Komponen Movable Pulley Driven (Mpdn) Pada Transmisi Kendaraan

Overlay welding analysis on GTAW and SMAW processes in terms of mechanical properties and corrosion rate

Experimental Investigation on Stainless-Steel Weld Overlay on Carbon Steel Plates Using Different Electrodes

Contact Info

Product

Resources

About