Antibody mounting capability of 1D/2D carbonaceous nanomaterials toward rapid-specific detection of SARS-CoV-2

Hashemi, Seyyed Alireza; Bahrani, Sonia; Mousavi, Seyyed Mojtaba; Omidifar, Navid; Behbahan, Nader Ghaleh Golab; Arjmand, Mohammad; Ramakrishna, Seeram; Dimiev, Ayrat M.; Lankarani, Kamran Bagheri; Moghadami, Mohsen; Firoozsani, Mohammad

doi:10.1016/j.talanta.2021.123113

Cited by 18 publications

(11 citation statements)

References 32 publications

(36 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The application of Gr derivatives (GO and reduced GO) could also be used in antibody mounting capability and detection. 24 Those demostrations show the potential of Gr- and CNT-based composites in enhancing the properties and performance of polymeric and carbonaceous materials in various applications.…”

Section: Introductionmentioning

confidence: 94%

Tailoring mechanical and electrical properties of polydimethylsiloxane nanocomposites With graphene and carbon nanotubes for wearable electronics

Huang

Chou

et al. 2023

Polymers and Polymer Composites

View full text Add to dashboard Cite

We explored the use of soft and flexible graphene (Gr)-reinforced polydimethylsiloxane (PDMS; Gr-PDMS) and Gr-carbon nanotube (CNT)-reinforced PDMS (Gr-CNT-PDMS) as nanocomposites (NCPs) in wearable electronic applications and investigated their mechanical and electrical properties. Specifically, we evaluated the mechanical reinforcement of the NCPs by performing Shore scleroscope hardness and machine-washing tests and evaluated their electrical properties by using a four-point probe. The results revealed that as the Gr or CNT concentrations increased, the NCPs’ hardness and surface resistance increased and decreased, respectively. Scanning electron microscopy revealed the formation of layered polymeric structures in the Gr-PDMS NCPs, contributing to the increase in hardness and decrease in surface resistance. Furthermore, bending tests revealed that changes in resistance were positively correlated with the Gr concentration. PDMS with low Gr concentrations exhibited no substantial changes in surface resistance after bending tests. However, for PDMS, as the Gr concentration increased (>5 wt.%), the cross-sectional morphology observed after 500 bending cycles differed substantially from that before observed bending tests. Additionally, the influence of one-dimensional (CNT) and two-dimensional (Gr) nanomaterials on the mechanical and electrical properties of the flexible PDMS samples was investigated. The aim of this study is to highlight the importance of considering the properties of different nanomaterials in developing high-performance NCPs for wearable electronics.

show abstract

Section: Introductionmentioning

confidence: 94%

Tailoring mechanical and electrical properties of polydimethylsiloxane nanocomposites With graphene and carbon nanotubes for wearable electronics

Huang

Chou

et al. 2023

Polymers and Polymer Composites

View full text Add to dashboard Cite

show abstract

“…Biopolymers, lignin, and chitosan are among the biological materials that can be converted into carbon materials by carbonization, just like the materials obtained by pyrolysis and calcination. Biopolymers have also been used to produce capacitors and porous carbonaceous compounds, which can be used to generate capacitors and porous frameworks [137–140] . Carbon materials are produced by direct carbonization of lignin, which has a weak capacity due to the low surface area of the material because of the lack of surface porosity.…”

Section: Biopolymers In Energy Generation and Storagementioning

confidence: 99%

Bioresource Polymer Composite for Energy Generation and Storage: Developments and Trends

Mousavi

Hashemi

Kalashgrani

et al. 2023

The Chemical Record

View full text Add to dashboard Cite

The ever‐growing demand of human society for clean and reliable energy sources spurred a substantial academic interest in exploring the potential of biological resources for developing energy generation and storage systems. As a result, alternative energy sources are needed in populous developing countries to compensate for energy deficits in an environmentally sustainable manner. This review aims to evaluate and summarize the recent progress in bio‐based polymer composites (PCs) for energy generation and storage. The articulated review provides an overview of energy storage systems, e. g., supercapacitors and batteries, and discusses the future possibilities of various solar cells (SCs), using both past research progress and possible future developments as a basis for discussion. These studies examine systematic and sequential advances in different generations of SCs. Developing novel PCs that are efficient, stable, and cost‐effective is of utmost importance. In addition, the current state of high‐performance equipment for each of the technologies is evaluated in detail. We also discuss the prospects, future trends, and opportunities regarding using bioresources for energy generation and storage, as well as the development of low‐cost and efficient PCs for SCs.

show abstract

“…The emergence of biosensors has facilitated the rapid diagnosis of a disease by replacing conventional, slow, and high-cost methods. Therefore, before a patient starts to deteriorate, the treatment process could be immediately initiated. − Acute myocardial infarction (AMI) is one of the leading causes of death in the developed world. The prevalence of the disease approaches 3 million people worldwide, with more than 1 million deaths in the United States annually.…”

Section: Introductionmentioning

confidence: 99%

Label-Free Detection of Cardiac Biomarkers: A Review on Microfluidic Electrochemical Biosensors

Zadeh

Hosseini

Mohammadnejad

et al. 2023

ACS Appl. Bio Mater.

Self Cite

View full text Add to dashboard Cite

Biosensors are valuable tools for the detection of biological species, including cells, pathogens, proteins, and other biological molecules. Biosensing devices integrated with microfluidics not only allow for easier sample preparation, portability, and reduced detection time and cost but also offer unique features such as label-free detection and improved sensitivity. Cardiovascular diseases (CVDs), particularly acute myocardial infarction, which is considered one of the main causes of death, are currently diagnosed by electrocardiography (ECG), which has been proven to be inadequate. To overcome the limitations of ECG, the efficient detection of cardiac biomarkers and specifically the measurement of cardiac troponins (cTnT and cTnI) are suggested. This review aims to expound on microfluidics, the most recent materials to develop these devices, and their application in medical diagnosis, particularly in CVD detection. Moreover, we will explore some of the prevalent and last readout methods to investigate in-depth electrochemical label-free detection methods for CVDs, primarily based on voltammetry and electrochemical impedance spectroscopy, with the main focus on structural details.

show abstract

Antibody mounting capability of 1D/2D carbonaceous nanomaterials toward rapid-specific detection of SARS-CoV-2

Cited by 18 publications

References 32 publications

Tailoring mechanical and electrical properties of polydimethylsiloxane nanocomposites With graphene and carbon nanotubes for wearable electronics

Tailoring mechanical and electrical properties of polydimethylsiloxane nanocomposites With graphene and carbon nanotubes for wearable electronics

Bioresource Polymer Composite for Energy Generation and Storage: Developments and Trends

Label-Free Detection of Cardiac Biomarkers: A Review on Microfluidic Electrochemical Biosensors

Contact Info

Product

Resources

About