A 40-nm CMOS Mixer with 36-GHz IF Bandwidth and 60–148 GHz RF Passband

Wu, Yen-Ting; Hwang, Yean Ren; Chiong, Chau-Ching; Lu, Bo-Ze; Wang, Huei

doi:10.1109/apmc46564.2019.9038677

Cited by 3 publications

(1 citation statement)

References 8 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Wu et al used a T-shaped transmission lines. 99 To enhance the bandwidth, a modified Marchand balun is proposed. The proposed design covered a small area and better port isolation.…”

Section: Microstrip Line Matchingmentioning

confidence: 99%

Recent advancement in the design of mixers for software‐defined radios

Mehta

Donelli

2021

Int J RF Mic Comp-Aid Eng

View full text Add to dashboard Cite

The implementation of software-defined radio necessitates a versatile radio frequency (RF) front-end that can support multiple standards in different frequency bands. This article presents the state-of-the-art multiband and wideband mixers in the context of different receiver architectures suitable for softwaredefined radio (SDR). Wideband and multiband mixer designs reported in the literature are categorized on the basis of their circuit architecture. This study tabulates the results of mixer designs with an emphasis on noise figure (NF), conversion gain (CG), linearity, and image rejection ratio. The best parameters reported in the comparison are 68-84 dB of CG, 3.2 dB of NF, 2.5 mW of power consumption, 12.5 dBm of third-order input intercept point, and 0.015 mm 2 of area at different frequencies. The study also discusses the design challenges and techniques to overcome those issues. The article concludes with the summary and prospective developments for SDR architectures.

show abstract

“…Wu et al used a T-shaped transmission lines. 99 To enhance the bandwidth, a modified Marchand balun is proposed. The proposed design covered a small area and better port isolation.…”

Section: Microstrip Line Matchingmentioning

confidence: 99%

Recent advancement in the design of mixers for software‐defined radios

Mehta

Donelli

2021

Int J RF Mic Comp-Aid Eng

View full text Add to dashboard Cite

show abstract

Optimal design ofCMOSmixer: A research review

Zhang

Tang²,

Cai

et al. 2022

Int J RF Mic Comp-Aid Eng

View full text Add to dashboard Cite

A mixer is an indispensable device in the RF transceiver system. Along with the rapid development of mobile communication technology, the demand on the RF mixer for compatibility with multiple communication standards and functional diversity is increasing. As a result, the mixer with wider bandwidth, lower noise, higher linearity, and less power consumption is urgently needed.In the article, the basic principle and the circuit architectures of the mixer are reviewed, including the essential performances such as linearity, noise, gain, bandwidth, and so forth. In addition, several aspects are presented, compared, and discussed with particular emphasis on optimization design approach and performance. Current design and fabrication challenges, future development, application areas of the mixer and visions for the mixer are also discussed in this review.

show abstract

An Innovative Joint-Injection Mixer With Broadband If and RF for Advanced Heterodyne Receivers of Millimeter-Wave Astronomy

Hwang

Chiong

et al. 2020

IEEE Trans. Microwave Theory Techn.

View full text Add to dashboard Cite

A 40-nm CMOS Mixer with 36-GHz IF Bandwidth and 60–148 GHz RF Passband

Cited by 3 publications

References 8 publications

Recent advancement in the design of mixers for software‐defined radios

Recent advancement in the design of mixers for software‐defined radios

Optimal design ofCMOSmixer: A research review

An Innovative Joint-Injection Mixer With Broadband If and RF for Advanced Heterodyne Receivers of Millimeter-Wave Astronomy

Contact Info

Product

Resources

About