We discuss the main challenges for the fabrication of emerging microLED displays. We shown that microtube technology is very well adapted to these new kind of displays, since it provides both mechanical and electrical connection of the microLEDs on the receiving substrate. Also, we present a new fabrication approach, where an elementary unit consists of all-in-one-RBG MicroLEDs on CMOS driving circuit.

The light-emitting diode (LED) is among promising candidates of light sources in visible light communication (VLC); however, strong internal polarization fields in common c-plane LEDs, especially green LEDs, result in low frequency and limited transmission performance. This study aims to overcome the limited 3-dB bandwidth of long-wavelength InGaN/GaN LEDs. Thus, semipolar (20–21) micro-LEDs (μLEDs) were fabricated through several improved approaches on epitaxy and chip processes. The μLED exhibits a 525 nm peak wavelength and good polarization performance. The highest 3-dB bandwidth up to 756 MHz and 1.5 Gbit/s data rate was achieved under a current density of 2.0 kA/cm2. These results suggest a good transmission capacity of green semipolar (20–21) μLEDs in VLC applications.

We have studied the growth of GaInNAs by a plasma-assisted molecular-beam epitaxy (MBE). It was found that the N-radicals were incorporated into the epitaxial layer like dopant atoms. In the range of 400–500 °C, the growth temperature (Tg) mainly affected the crystal quality of GaInNAs rather than the N concentration. The N concentration dropped rapidly when Tg exceeded 500 °C. Considering N desorption alone is insufficient to account for the strong falloff of the N concentration with Tg over 500 °C, the effect of thermally-activated N surface segregation must be taken into account. The N concentration was independent of the arsenic pressure and the In concentration in GaInNAs layers, but inversely proportional to the growth rate. Based on the experimental results, a kinetic model including N desorption and surface segregation was developed to analyze quantitatively the N incorporation in MBE growth.

High-quality epitaxial layers are directly related to internal quantum efficiency. The methods used to design such epitaxial layers are reviewed in this article. The ultraviolet C (UVC) light-emitting diode (LED) epitaxial layer structure exhibits electron leakage; therefore, many research groups have proposed the design of blocking layers and carrier transportation to generate high electron–hole recombination rates. This also aids in increasing the internal quantum efficiency. The cap layer, p-GaN, exhibits high absorption in deep UV radiation; thus, a small thickness is usually chosen. Flip chip design is more popular for such devices in the UV band, and the main factors for consideration are light extraction and heat transportation. However, the choice of encapsulation materials is important, because unsuitable encapsulation materials will be degraded by ultraviolet light irradiation. A suitable package design can account for light extraction and heat transportation. Finally, an atomic layer deposition Al2O3 film has been proposed as a mesa passivation layer. It can provide a low reverse current leakage. Moreover, it can help increase the quantum efficiency, enhance the moisture resistance, and improve reliability. UVC LED applications can be used in sterilization, water purification, air purification, and medical and military fields.

We investigate the spatial variation of the external quantum efficiency (EQE) of InGaN lightemitting diodes. Two different types of EQE droop are examined in one single device, offering unambiguous analyses on the underlying material physics without the complications of the processing variation. The interplays of microscopic defects, extended defects, and energy fluctuation dictate the mechanisms of the droop, which represents a common theme in various optoelectronic devices. The two droop types correspond to the two extreme situations of energy fluctuation that affects the carrier diffusion and recombination. The finding suggests ways for improving the device performance, depending on operation conditions. V

In terms of their use in displays, quantum dots (QDs) exhibit several advantages, including high illumination efficiency and color rendering, low-cost, and capacity for mass production. Furthermore, they are environmentally friendly. Excellent luminescence and charge transport properties of QDs led to their application in QD-based light-emitting diodes (LEDs), which have attracted considerable attention in display and solid-state lighting applications. In this review, we discuss the applications of QDs which are used on color conversion filter that exhibit high efficiency in white LEDs, full-color micro-LED devices, and liquid-type structure devices, among others. Furthermore, we discuss different QD printing processes and coating methods to achieve the full-color micro-LED. With the rise in popularity of wearable and see-through red, green, and blue (RGB) full-color displays, the flexible substrate is considered as a good potential candidate. The anisotropic conductive film method provides a small controllable linewidth of electrically conductive particles. Finally, we discuss the advanced application for flexible full-color and highly efficient QD micro-LEDs. The general conclusion of this study also involves the demand for a more straightforward QD deposition technique, whose breakthrough is expected.

We perform both spatially resolved electroluminescence (SREL) as a function of injection current and spatially resolved photoluminescence (SRPL) as a function of excitation power on InGaN quantum well blue light-emitting diodes to investigate the underlying physics for the phenomenon of the external quantum efficiency (EQE) droop. SREL allows us to study two most commonly observed but distinctly different droop behaviors on a single device, minimizing the ambiguity trying to compare independently fabricated devices. Two representative devices are studied: one with macroscopic scale material non-uniformity, the other being macroscopically uniform, but both with microscopic scale fluctuations. We suggest that the EQE–current curve reflects the interplay of three effects: nonradiative recombination through point defects, carrier localization due to either In composition or well width fluctuation, and nonradiative recombination of the extended defects, which is common to various optoelectronic devices. By comparing SREL and SRPL, two very different excitation/detection modes, we show that individual singular sites exhibiting either particularly strong or weak emission in SRPL do not usually play any significant and direct role in the EQE droop. We introduce a two-level model that can capture the basic physical processes that dictate the EQE–current dependence and describe the whole operating range of the device from 0.01 to 100 A/cm2.

A solution for multi-functional indoor light sources is proposed to achieve the new concept of healthy lighting. A remotely controllable light source that embodies a quadruple-chip light-emitting diode and driven by pulse-width-modulation currents is designed. Therefore, spectral power distributions (SPDs) of the light source can be readily controlled. An algorithm, namely the optical power ratio algorithm, is developed to select all suitable SPDs adapted for various applications. Principles of selection are based on those traditional visual indices, as well as on some non-visual parameters such as circadian action factor, circadian efficacy of radiation and circadian illuminance. We investigate in detail the correlation among these parameters and provide SPDs with both decent visual and non-visual performances for three typical cases. The study suggests some fundamental principles for designing healthy light sources, and can be regarded as a guide for designing indoor light sources of the next generation.