This study investigates an advanced copper (Cu) chemical displacement technique (CDT) with varying the chemical displacement time for fabricating Cu/SiO2-stacked resistive random-access memory (ReRAM). Compared with other Cu deposition methods, this CDT easily controls the interface of the Cu-insulator, the switching layer thickness, and the immunity of the Cu etching process, assisting the 1-transistor-1-ReRAM (1T-1R) structure and system-on-chip integration. The modulated shape of the Cu-SiO2 interface and the thickness of the SiO2 layer obtained by CDT-based Cu deposition on SiO2 were confirmed by scanning electron microscopy and atomic force microscopy. The CDT-fabricated Cu/SiO2-stacked ReRAM exhibited lower operation voltages and more stable data retention characteristics than the control Cu/SiO2-stacked sample. As the Cu CDT processing time increased, the forming and set voltages of the CDT-fabricated Cu/SiO2-stacked ReRAM decreased. Conversely, decreasing the processing time reduced the on-state current and reset voltage while increasing the endurance switching cycle time. Therefore, the switching characteristics were easily modulated by Cu CDT, yielding a high performance electrochemical metallization (ECM)-type ReRAM.

Electrochemical-metallization-type resistive random access memories (ReRAMs) show promising performance as next-generation nonvolatile memory. In this paper, the Cu chemical displacement technique (CDT) is used to form the bottom electrode of ReRAM devices. Compared with conventional deposition methods, the Cu-CDT method has numerous advantages for ReRAM fabrication, including low cost, low temperature fabrication, and the provision of unconsolidated Cu film and large surface roughness. Moreover, the Cu-CDT method is a favorable candidate for overcoming the Cu etching problem and is thus suitable for fabricating ReRAM devices. Using this technique, the surface morphology of a thin Cu film can be easily controlled. The obtained results show that the electric fields during the Forming and SET operations decreased, and the on-state current increased in the RESET operation, as the Cu-CDT displacement time was increased. The Cu-CDT samples exhibited a low operation field, large memory window (>106), and excellent endurance switching cycle characteristics. Moreover, this paper proposes a model to explain the electrical characteristics of ReRAM, which are dependent on the surface morphology.

No abstract

In this study, a high-performance TixZrySizO flash memory is demonstrated using a sol–gel spin-coating method and formed under a low annealing temperature. The high-efficiency charge storage layer is formed by depositing a well-mixed solution of titanium tetrachloride, silicon tetrachloride, and zirconium tetrachloride, followed by 60 s of annealing at 600°C. The flash memory exhibits a noteworthy hot hole trapping characteristic and excellent electrical properties regarding memory window, program/erase speeds, and charge retention. At only 6-V operation, the program/erase speeds can be as fast as 120:5.2 μs with a 2-V shift, and the memory window can be up to 8 V. The retention times are extrapolated to 106 s with only 5% (at 85°C) and 10% (at 125°C) charge loss. The barrier height of the TixZrySizO film is demonstrated to be 1.15 eV for hole trapping, through the extraction of the Poole-Frenkel current. The excellent performance of the memory is attributed to high trapping sites of the low-temperature-annealed, high-κ sol–gel film.

In this work, the sol-gel derived ZrO x thin film as switching layer is proposed for Cu/ZrO x /TaN ReRAM device application. The resistive switching behavior is suggested to the formation and rupture Cu conductive filaments. The device shows the good electrical properties including forming free, low switching voltages (set/reset), high on/off ratio, better uniformity of Set/Reset and HRS/LRS distributions, and good stability data retention characteristics. Beside, the good switching property is due to the porous structure of sol-gel derived ZrO x thin film leading Cu ion fast migration into switching layer.

No abstract

In this study, a polyimide (PI) thin film is synthesized as a resistive switching layer for resistive random access memory (ReRAM) applications. The experimental results on polyimide thickness show that the Schottky effect between the interface of polyimide and metal thin films is the dominant mechanism in the high-resistance state (HRS). We, therefore, propose a rubbing post-treatment to improve the device performance. Results show that the uniformity and leakage of the memory in the HRS, as well as the power consumption in the low-resistance state (LRS), are improved. The power density of the set process is less than half after the rubbing post-treatment. Moreover, the power density of the reset process can be markedly decreased by about two orders of magnitude. In addition, the rubbed ReRAM exhibits a stable storage capability with seven orders of magnitude I ON/I OFF current ratio at 85 °C.

No abstract