Abstract-Retention errors, caused by charge leakage over time, are the dominant source of flash memory errors. Understanding, characterizing, and reducing retention errors can significantly improve NAND flash memory reliability and endurance. In this paper, we first characterize, with real 2y-nm MLC NAND flash chips, how the threshold voltage distribution of flash memory changes with different retention age -the length of time since a flash cell was programmed. We observe from our characterization results that 1) the optimal read reference voltage of a flash cell, using which the data can be read with the lowest raw bit error rate (RBER), systematically changes with its retention age, and 2) different regions of flash memory can have different retention ages, and hence different optimal read reference voltages. Based on our findings, we propose two new techniques. First, Retention Optimized Reading (ROR) adaptively learns and applies the optimal read reference voltage for each flash memory block online. The key idea of ROR is to periodically learn a tight upper bound, and from there approach the optimal read reference voltage. Our evaluations show that ROR can extend flash memory lifetime by 64% and reduce average error correction latency by 10.1%, with only 768 KB storage overhead in flash memory for a 512 GB flash-based SSD. Second, Retention Failure Recovery (RFR) recovers data with uncorrectable errors offline by identifying and probabilistically correcting flash cells with retention errors. Our evaluation shows that RFR reduces RBER by 50%, which essentially doubles the error correction capability, and thus can effectively recover data from otherwise uncorrectable flash errors.

Abstract-NAND flash memory reliability continues to degrade as the memory is scaled down and more bits are programmed per cell. A key contributor to this reduced reliability is read disturb, where a read to one row of cells impacts the threshold voltages of unread flash cells in different rows of the same block. Such disturbances may shift the threshold voltages of these unread cells to different logical states than originally programmed, leading to read errors that hurt endurance.For the first time in open literature, this paper experimentally characterizes read disturb errors on state-of-the-art 2Y-nm (i.e., 20-24 nm) MLC NAND flash memory chips. Our findings (1) correlate the magnitude of threshold voltage shifts with read operation counts, (2) demonstrate how program/erase cycle count and retention age affect the read-disturb-induced error rate, and (3) identify that lowering pass-through voltage levels reduces the impact of read disturb and extend flash lifetime. Particularly, we find that the probability of read disturb errors increases with both higher wear-out and higher pass-through voltage levels.We leverage these findings to develop two new techniques. The first technique mitigates read disturb errors by dynamically tuning the pass-through voltage on a per-block basis. Using real workload traces, our evaluations show that this technique increases flash memory endurance by an average of 21%. The second technique recovers from previously-uncorrectable flash errors by identifying and probabilistically correcting cells susceptible to read disturb errors. Our evaluations show that this recovery technique reduces the raw bit error rate by 36%.

NAND flash memory is ubiquitous in everyday life today because its capacity has continuously increased and cost has continuously decreased over decades. This positive growth is a result of two key trends: (1) effective process technology scaling; and (2) multi-level (e.g., MLC, TLC) cell data coding. Unfortunately, the reliability of raw data stored in flash memory has also continued to become more difficult to ensure, because these two trends lead to (1) fewer electrons in the flash memory cell floating gate to represent the data; and (2) larger cell-to-cell interference and disturbance effects. Without mitigation, worsening reliability can reduce the lifetime of NAND flash memory. As a result, flash memory controllers in solid-state drives (SSDs) have become much more sophisticated: they incorporate many effective techniques to ensure the correct interpretation of noisy data stored in flash memory cells. In this article, we review recent advances in SSD error characterization, mitigation, and data recovery techniques for reliability and lifetime improvement. We provide rigorous experimental data from state-ofthe-art MLC and TLC NAND flash devices on various types of flash memory errors, to motivate the need for such techniques. Based on the understanding developed by the experimental characterization, we describe several mitigation and recovery techniques, including (1) cell-to-cell interference mitigation; (2) optimal multi-level cell sensing; (3) error correction using state-of-the-art algorithms and methods; and (4) data recovery when error correction fails. We quantify the reliability improvement provided by each of these techniques. Looking forward, we briefly discuss how flash memory and these techniques could evolve into the future.

Abstract-Memory devices represent a key component of datacenter total cost of ownership (TCO), and techniques used to reduce errors that occur on these devices increase this cost. Existing approaches to providing reliability for memory devices pessimistically treat all data as equally vulnerable to memory errors. Our key insight is that there exists a diverse spectrum of tolerance to memory errors in new data-intensive applications, and that traditional one-size-fits-all memory reliability techniques are inefficient in terms of cost. For example, we found that while traditional error protection increases memory system cost by 12.5%, some applications can achieve 99.00% availability on a single server with a large number of memory errors without any error protection. This presents an opportunity to greatly reduce server hardware cost by provisioning the right amount of memory reliability for different applications.Toward this end, in this paper, we make three main contributions to enable highly-reliable servers at low datacenter cost. First, we develop a new methodology to quantify the tolerance of applications to memory errors. Second, using our methodology, we perform a case study of three new dataintensive workloads (an interactive web search application, an in-memory key-value store, and a graph mining framework) to identify new insights into the nature of application memory error vulnerability. Third, based on our insights, we propose several new hardware/software heterogeneous-reliability memory system designs to lower datacenter cost while achieving high reliability and discuss their trade-offs. We show that our new techniques can reduce server hardware cost by 4.7% while achieving 99.90% single server availability.

No abstract

No abstract

Although transistor density continues to increase, voltage scaling has stalled and thus power density is increasing each technology generation. Particularly in mobile devices, which have limited cooling options, these trends lead to a utilization wall in which sustained chip performance is limited primarily by power rather than area. However, many mobile applications do not demand sustained performance; rather they comprise short bursts of computation in response to sporadic user activity.To improve responsiveness for such applications, this paper explores activating otherwise powered-down cores for sub-second bursts of intense parallel computation. The approach exploits the concept of computational sprinting, in which a chip temporarily exceeds its sustainable thermal power budget to provide instantaneous throughput, after which the chip must return to nominal operation to cool down. To demonstrate the feasibility of this approach, we analyze the thermal and electrical characteristics of a smart-phone-like system that nominally operates a single core (∼1W peak), but can sprint with up to 16 cores for hundreds of milliseconds. We describe a thermal design that incorporates phase-change materials to provide thermal capacitance to enable such sprints. We analyze image recognition kernels to show that parallel sprinting has the potential to achieve the task response time of a 16W chip within the thermal constraints of a 1W mobile platform.

No abstract