In this work, we study the detection of acetylene (C2H2), carbon dioxide (CO2) and water vapor (H2O) gases in the near-infrared (NIR) range using an on-chip silicon micro-electro-mechanical system (MEMS) Fourier transform infrared (FT-IR) spectrometer in the wavelength range 1300-2500 nm (4000-7692 cm(-1)). The spectrometer core engine is a scanning Michelson interferometer micro-fabricated using a deep-etching technology producing self-aligned components. The light is free-space propagating in-plane with respect to the silicon chip substrate. The moving mirror of the interferometer is driven by a relatively large stroke electrostatic comb-drive actuator corresponding to about 30 cm(-1) resolution. Multi-mode optical fibers are used to connect light between the wideband light source, the interferometer, the 10 cm gas cell, and the optical detector. A wide dynamic range of gas concentration down to 2000 parts per million (ppm) in only 10 cm length gas cell is demonstrated. Extending the wavelength range to the mid-infrared (MIR) range up to 4200 nm (2380 cm(-1)) is also experimentally demonstrated, for the first time, using a bulk micro-machined on-chip MEMS FT-IR spectrometer. The obtained results open the door for an on-chip optical gas sensor for many applications including environmental sensing and industrial process control in the NIR/MIR spectral ranges.

The integration of microactuators within a silicon photonic chip gave rise to the field of optical micro‐electro‐mechanical systems (MEMS) that was originally driven by the telecommunication market. Following the latter's bubble collapse in the beginning of the third millennium, new directions of research with considerable momentum appeared focusing on the realization and applications of miniaturized instrumentation in biology, chemistry, physics and materials science. At the heart of these applications light interferometry is a key optical phenomenon, in which miniaturized scanning interferometers are the manipulating optical devices. Monolithic free‐space optical interferometers realized on a silicon chip take advantage of the recent progress in the microfabrication technology that is enabling accurate control of the etching depth, the aspect ratio, the verticality and the curvature of the etched surfaces. The fabrication technology, the library of micro‐optical and mechanical components, the realized architectures and their characterization are described in detail in this review, followed by a discussion of the foreseen challenges.

Miniaturized optical benches process free-space light propagating in-plane with respect to the substrate and have a large variety of applications, including the coupling of light through an optical fiber. High coupling efficiency is usually obtained using assembled micro-optical parts, which considerably increase the system cost and integration effort. In this work, we report a high coupling efficiency, monolithically integrated silicon micromirror with controlled three-dimensional (3D) curvature that is capable of manipulating optical beams propagating in the plane of the silicon substrate. Based on our theoretical modeling, a spherical micromirror with a microscale radius of curvature as small as twice the Gaussian beam Rayleigh range provides a 100% coupling efficiency over a relatively long optical path range. Introducing dimensionless parameters facilitates the elucidation of the role of key design parameters, including the mirror's radii of curvature, independent of the wavelength. A micromachining method is presented for fabricating the 3D micromirror using fluorinated gas plasmas. The measured coupling efficiency was greater than 50% over a 200-mm optical path, compared to less than 10% afforded by a conventional flat micromirror, which was in good agreement with the model. Using the 3D micromirror, an optical cavity was formed with a round-trip diffraction loss of less than 0.4%, resulting in one order of magnitude enhancement in the measured quality factor. A nearly 100% coupling was also estimated when matching the sagittal and tangential radii of curvature of the presented micromirror's surface. The reported class of 3D micromirrors may be an advantageous replacement for the optical lenses usually assembled in silicon photonics and optical benches by transforming them into real 3D monolithic systems while achieving wideband high coupling efficiency over submillimeter distances.

Optical spectrometers enable contactless chemical analysis. However, decreasing both their size and cost appears to be a prerequisite to their widespread deployment. Chip-scale implementation of optical spectrometers still requires tackling two main challenges. First, operation over a broad spectral range extending to the infrared is required to enable covering the molecular absorption spectrum of a broad variety of materials. This is addressed in our work with an Micro-Electro Mechanical Systems (MEMS)-based Fourier transform infrared spectrometer with an embedded movable micro-mirror on a silicon chip. Second, fine spectral resolution Δλ is also required to facilitate screening over several chemicals. A fundamental limit states that Δλ is inversely proportional to the mirror motion range, which cannot exceed the chip size. To boost the spectral resolution beyond this limit, we propose the concept of parallel (or multi-core) FTIR, where multiple interferometers provide complementary optical paths using the same actuator and within the same chip. The concept scalability is validated with 4 interferometers, leading to approximately 3 times better spectral resolution. After the atmospheric contents of a greenhouse gas are monitored, the methane absorption bands are successfully measured and discriminated using the presented device.

Microplastics contaminating drinking water is a growing issue that has been the focus of a few recent studies, where a major bottleneck is the time-consuming analysis. In this work, a micro-optofluidic platform is proposed for fast quantification of microplastic particles, the identification of their chemical nature and size, especially in the 1–100 µm size range. Micro-reservoirs ahead of micro-filters are designed to accumulate all trapped solid particles in an ultra-compact area, which enables fast imaging and optical spectroscopy to determine the plastic nature and type. Furthermore, passive size sorting is implemented for splitting the particles according to their size range in different reservoirs. Besides, flow cytometry is used as a reference method for retrieving the size distribution of samples, where chemical nature information is lost. The proof of concept of the micro-optofluidic platform is validated using model samples where standard plastic particles of different size and chemical nature are mixed.

No abstract

No abstract

A wide angle microscanning architecture is presented in which the angular deflection is achieved by displacing the principle axis of a curved silicon micromirror of acylindrical shape, with respect to the incident beam optical axis. The micromirror curvature is designed to overcome the possible deformation of the scanned beam spot size during scanning. In the presented architecture, the optical axis of the beam lays in-plane with respect to the substrate opening the door for a completely integrated and self-aligned miniaturized scanner. A micro-optical bench scanning device, based on translating a 200 μm focal length micromirror by an electrostatic comb-drive actuator, is implemented on a silicon chip. The microelectromechanical system has a resonance frequency of 329 Hz and a quality factor of 22. A single-mode optical fiber is used as the optical source and inserted into a micromachined groove fabricated and lithographically aligned with the microbench. Optical deflection angles up to 110 degrees are demonstrated.