Because of the problems associated with the generation and storage of hydrogen in portable applications, the use of ammonia has been proposed for on-site production of hydrogen through ammonia decomposition. First, an analysis of the existing systems for ammonia decomposition and the challenges for this technology are presented. Then, the state of the art of the catalysts used to date for ammonia decomposition is described considering the catalysts composed of noble and non-noble metals and their combinations, as well as novel materials such as alkali metal amides and imides. The effect of the supports and promoters used is analyzed in detail, and the catalytic activity obtained is compared. An analysis of the kinetics of the reaction obtained with different catalysts is also presented and discussed, including the reaction mechanism, the determining step of the reaction, and the apparent activation energy. Finally, the structured reactors used to date for the decomposition reaction of ammonia are explored, as well as the possibilities offered by catalytic membrane reactors, which allow the on-site simultaneous production and separation of hydrogen.

Experimental and computed results show a multiband behaviour over five bands for the new fractal Sierpinski antenna. Such a behaviour is based on the self-similarity properties of the antenna's fractal shape, which might open an alternative way for designing new multiband and frequency independent antennas.Introduction: Most antenna designs are highly frequency dependent. The size of the antenna relative to the operating wavelength is the main bandwidth limiting factor. In the early 1960s, some selfscalable structures such as spirals, cones and log-periodic arrays were developed to design frequency independent antennas [2 ~ 51. The common factor is that the shape of all these structures remains invariable under some scaling transformations.

The development of better catalysts is a passionate topic at the forefront of modern science, where operando techniques are necessary to identify the nature of the active sites. The surface of a solid catalyst is dynamic and dependent on the reaction environment and, therefore, the catalytic active sites may only be formed under specific reaction conditions and may not be stable either in air or under high vacuum conditions. The identification of the active sites and the understanding of their behaviour are essential information towards a rational catalyst design. One of the most powerful operando techniques for the study of active sites is near ambient pressure X-ray photoelectron spectroscopy (NAP-XPS), which is particularly sensitive to the surface and sub-surface of solids. Here we review the use of NAP-XPS for the study of ceria-based catalysts, widely used in a large number of industrial processes due to their excellent oxygen storage capacity and well-established redox properties.

Hydrogen, produced by water splitting, has been proposed as one of the main green energy vectors of the future if produced from renewable energy sources. However, to substitute fossil fuels, large amounts of pure water are necessary, scarce in many world regions. In this work, we fabricate efficient and earth-abundant electrodes, study the challenges of using real seawater, and propose an electrode regeneration method to face undesired salt deposition. NiÀ MoÀ Fe trimetallic electrocatalyst is deposited on non-expensive graphitic carbon felts both for hydrogen (HER) and oxygen evolution reactions (OER) in seawater and alkaline seawater. Cl À pitting and the chlorine oxidation reaction are suppressed on these substrates and alkalinized electrolyte. Precipitations on the electrodes, mainly CaCO 3 , originating from seawater-dissolved components have been studied, and a simple regeneration technique is proposed to rapidly dissolve undesired deposited CaCO 3 in acidified seawater. Under alkaline conditions, NiÀ MoÀ Fe-based catalyst is found to reconfigure, under cathodic bias, into NiÀ MoÀ Fe alloy with a cubic crystalline structure and Ni : Fe(OH) 2 redeposits whereas, under anodic bias, it is transformed into a follicular Ni: FeOOH structure. High productivities over 300 mA cm À 2 and voltages down to 1.59 V@10 mA cm À 2 for the overall water splitting reaction have been shown, and electrodes are found stable for over 24 h without decay in alkaline seawater conditions and with energy efficiency higher than 61.5 % which makes seawater splitting promising and economically feasible.

Efficiently treating methane emissions in transportation remains a challenge. Here, we investigate palladium and platinum mono- and bimetallic ceria-supported catalysts synthesized by mechanical milling and by traditional impregnation for methane total oxidation under dry and wet conditions, reproducing those present in the exhaust of natural gas vehicles. By applying a toolkit of in situ synchrotron techniques (X-ray diffraction, X-ray absorption and ambient pressure photoelectron spectroscopies), together with transmission electron microscopy, we show that the synthesis method greatly influences the interaction and structure at the nanoscale. Our results reveal that the components of milled catalysts have a higher ability to transform metallic Pd into Pd oxide species strongly interacting with the support, and achieve a modulated PdO/Pd ratio than traditionally-synthesized catalysts. We demonstrate that the unique structures attained by milling are key for the catalytic activity and correlate with higher methane conversion and longer stability in the wet feed.

No abstract

The optimization of the supported Pd phase for CH4 activation on Pd/CeO2 catalysts has been a matter of great interest in the recent literature, aiming at the design of efficient...

Supported Pd/CeO2 catalytic systems have been widely investigated in the low-temperature oxidation of CO (LTO CO) due to the unique oxygen storage capacity and redox properties of the ceria support, which highly influence the structural, chemical and electronic state of Pd species. Herein, operando near-ambient pressure XPS (NAP-XPS) technique has allowed the study of a conventional Pd/CeO2 catalyst surface during the CO oxidation reaction under experimental conditions closer to the actual catalytic reaction, unfeasible with other surface science techniques that demand UHV conditions. SEM, HRTEM and XRD analyses of the powder catalyst, prepared by conventional incipient wetness impregnation, reveal uniformly CeO2-loaded Pd NPs of less than 2 nm size, which generated an increase in oxygen vacancies with concomitant ceria reduction, as indicated by H2-TPR and Raman measurements. Adsorbed peroxide (O22−) species on the catalyst surface could also be detected by Raman spectra. Operando NAP-XPS results obtained at the ALBA Synchrotron Light Source revealed two kinds of Pd species under reaction conditions, namely PdOx and PdII ions in a PdxCe1−xO2−δ solution, the latter one appearing to be crucial for the CO oxidation. By means of a non-destructive depth profile analysis using variable synchrotron excitation energies, the location and the role of these palladium species in the CO oxidation reaction could be clarified: PdOx was found to prevail on the upper surface layers of the metallic Pd supported NPs under CO, while under reaction mixture it was rapidly depleted from the surface, leaving a greater amount in the subsurface layers (7% vs. 12%, respectively). On the contrary, the PdxCe1−xO2−δ phase, which was created at the Pd–CeO2 interface in contact with the gas environment, appeared to be predominant on the surface of the catalyst. Its presence was crucial for CO oxidation evolution, acting as a route through which active oxygen species could be transferred from ceria to Pd species for CO oxidation.