No abstract

Perovskite solar cells (PSCs) have attracted tremendous attentions due to its high performance and rapid efficiency promotion. Compact layer plays a crucial role in transferring electrons and blocking charge recombination between the perovskite layer and fluorine-doped tin oxide (FTO) in PSCs. In this study, compact TiO2 layers were synthesized by spin-coating method with three different titanium precursors, titanium diisopropoxide bis (acetylacetonate) (c-TTDB), titanium isopropoxide (c-TTIP), and tetrabutyl titanate (c-TBOT), respectively. Compared with the PSCs based on the widely used c-TTDB and c-TTIP, the device based on c-TBOT has significantly enhanced performance, including open-circuit voltage, short-circuit current density, fill factor, and hysteresis. The significant enhancement is ascribed to its excellent morphology, high conductivity and optical properties, fast charge transfer, and large recombination resistance. Thus, a power conversion efficiency (PCE) of 17.03% has been achieved for the solar cells based on c-TBOT.Electronic supplementary materialThe online version of this article (10.1186/s11671-017-2418-9) contains supplementary material, which is available to authorized users.

No abstract

No abstract

Efficiency promotion has been severely constrained by charge recombination in perovskite solar cells (PSCs). Interface modification has been proved to be an effective way to reduce the interfacial charge recombination. In this work, a mesoporous TiO2 (mp-TiO2) layer was modified by an ultrathin BaTiO3 layer to suppress charge recombination in PSCs. The ultrathin BaTiO3 modification layer was prepared by the spin coating method using a barium salt solution. The concentration of the barium salt solution was optimized, and the effect of the BaTiO3 modification layer on the performance of the cells was also investigated. The modification layer can not only successfully retard charge recombination but also effectively boost the rate of electron extraction at the interface, resulting in enhanced open-circuit voltage (V oc), short circuit current density (J sc), and fill factor. Furthermore, the hysteresis of the PSCs was also significantly reduced after the modification. By optimizing and employing the BaTiO3 modification layer, the power conversion efficiency of the cells was increased from 16.13 to 17.87%.

In this paper, N-doped TiO2 (N-TiO2) nanorod arrays were synthesized with hydrothermal method, and perovskite solar cells were fabricated using them as electron transfer layer. The solar cell performance was optimized by changing the N doping contents. The power conversion efficiency of solar cells based on N-TiO2 with the N doping content of 1% (N/Ti, atomic ratio) has been achieved 11.1%, which was 14.7% higher than that of solar cells based on un-doped TiO2. To get an insight into the improvement, some investigations were performed. The structure was examined with X-ray powder diffraction (XRD), and morphology was examined by scanning electron microscopy (SEM). Energy dispersive spectrometer (EDS) and Tauc plot spectra indicated the incorporation of N in TiO2 nanorods. Absorption spectra showed higher absorption of visible light for N-TiO2 than un-doped TiO2. The N doping reduced the energy band gap from 3.03 to 2.74 eV. The photoluminescence (PL) and time-resolved photoluminescence (TRPL) spectra displayed the faster electron transfer from perovskite layer to N-TiO2 than to un-doped TiO2. Electrochemical impedance spectroscopy (EIS) showed the smaller resistance of device based on N-TiO2 than that on un-doped TiO2.Electronic supplementary materialThe online version of this article (doi:10.1186/s11671-016-1811-0) contains supplementary material, which is available to authorized users.

In this paper, Er3+-Yb3+-Li+ tri-doped TiO2 (UC-TiO2) was prepared by an addition of Li+ to Er3+-Yb3+ co-doped TiO2. The UC-TiO2 presented an enhanced up-conversion emission compared with Er3+-Yb3+ co-doped TiO2. The UC-TiO2 was applied to the perovskite solar cells. The power conversion efficiency (PCE) of the solar cells without UC-TiO2 was 14.0%, while the PCE of the solar cells with UC-TiO2 was increased to 16.5%, which presented an increase of 19%. The results suggested that UC-TiO2 is an effective up-conversion material. And this study provided a route to expand the spectral absorption of perovskite solar cells from visible light to near-infrared using up-conversion materials.Electronic supplementary materialThe online version of this article (10.1186/s11671-018-2545-y) contains supplementary material, which is available to authorized users.

A new up-conversion nanomaterial of Ho3+-Yb3+-Mg2+ tri-doped TiO2 (UC-Mg-TiO2) was designed and synthesized with a sol-gel method. The UC-Mg-TiO2 presented enhanced up-conversion fluorescence by an addition of Mg2+. The UC-Mg-TiO2 was utilized to fabricate perovskite solar cells by forming a thin layer on the electron transfer layer. The results display that the power conversion efficiency of the solar cells based on the electron transfer layer with UC-Mg-TiO2 is improved to 16.3 from 15.2% for those without UC-Mg-TiO2. It is demonstrated that the synthesized UC-Mg-TiO2 can convert the near-infrared light to visible light that perovskite film can absorb to improve the power conversion efficiency of the devices.Electronic supplementary materialThe online version of this article (10.1186/s11671-018-2681-4) contains supplementary material, which is available to authorized users.