Density profiles in pedestal region (H-mode) are measured in HL-2A and the characteristics of the density pedestal are described. Cold particle deposition by Supersonic Molecular Beam Injection (SMBI) within the pedestal is verified. ELM mitigation by SMBI into the H-mode pedestal is demonstrated and the relevant physics is elucidated. The sensitivity of the effect to SMBI pressure and duration are studied. Following SMBI, the ELM frequency increases and ELM amplitude decreases for a finite duration period. Increases in ELM frequency of SMBI ELM f / 0 ELM f 2-3.5 are achieved. This experiment argues that the ELM mitigation results from an increase in Page 2 higher frequency fluctuations and transport events in the pedestal, which are caused by SMBI. These inhibit the occurrence of large transport events which span the entire pedestal width. The observed change in the density pedestal profiles and edge particle flux spectrum with and without SMBI supports this interpretation. An analysis of the experiment and a model shows that ELMs can be mitigated by SMBI with shallow particle penetration into the pedestal.

The experimental results of low pressure supersonic molecular beam injection (SMBI) fuelling on the HL-2A closed divertor indicate that during the period of pulsed SMBI the power density convected at the target plate surfaces was 0.4 times of that before or after the beam injection. An empirical scaling law used for the SMBI penetration depth for the HL-2A plasma was obtained. The cluster jet injection (CJI) is a new fuelling method which is based on and developed from the experiments of SMBI in the HL-1M tokamak. The hydrogen clusters are produced at liquid nitrogen temperature in a supersonic adiabatic expansion of moderate backing pressure gases into vacuum through a Laval nozzle and are measured by Rayleigh scattering. The measurement results have shown that the averaged cluster size of as large as hundreds of atoms was found at the backing pressures of more than 0.1 MPa. Multifold diagnostics gave coincidental evidence that when there was hydrogen CJI in the HL-2A plasma, a great deal of particles from the jet were deposited at a terminal area rather than uniformly ablated along the injecting path. SMB with clusters, which are like micro-pellets, will be of benefit for deeper fuelling, and its injection behaviour was somewhat similar to that of pellet injection. Both the particle penetration depth and the fuelling efficiency of the CJI were distinctly better than that of the normal SMBI under similar discharge operation. During hydrogen CJI or high-pressure SMBI, a combination of collision and radiative stopping forced the runaway electrons to cool down to thermal velocity due to such a massive fuelling.

We report recent experimental results from HL-2A and KSTAR on ELM mitigation by supersonic molecular beam injection (SMBI). Cold particle deposition within the pedestal by SMBI is verified in both machines.The signatures of ELM mitigation by SMBI are an ELM frequency increase and ELM amplitude decrease.These persist for an SMBI influence time τI. Here, τI is the time for the SMBI influenced pedestal profile to refill. An increase in f SMBI ELM /f 0 ELM and a decrease in the energy loss per ELM WELM were achieved in both machines. Physical insight was gleaned from studies of density and vφ(toroidal rotation velocity) evolution, particle flux and turbulence spectra, divertor heat load. The characteristic gradients of the pedestal density soften and a change in vφwas observed during a τI time. The spectra of the edge particle flux Г~ < ˜vr˜ne> and density fluctuation with and without SMBI were measured in HL-2A and in KSTAR, respectively. A clear phenomenon observed is the decrease in divertor heat load during the τI time in HL-2A. Similar results are the profiles of saturation current density Jsat with and without SMBI in KSTAR. We note that τI/τp (particle confinement time) is close to ~1, although there is a large difference in individual τI between the two machines. This suggests that τI is strongly related to particle-transport events. Experiments and analysis of a simple phenomenological model support the important conclusion that ELM mitigation by SMBI results from an increase in higher frequency fluctuations and transport events in the pedestal.

We construct a diffusive, bi-stable cellular automata model to elucidate the physical mechanisms underlying observed edge localized mode (ELM) mitigation by supersonic molecular beam injection (SMBI). The extended cellular automata model reproduces key qualitative features of ELM mitigation experiments, most significantly the increase in frequency of grain ejection events (ELMs), and the decrease in the number of grains ejected by these transport events. The basic mechanism of mitigation is the triggering of small scale pedestal avalanches by additional grain injection directly into the H-mode pedestal. The small scale avalanches prevent the gradient from building-up to marginality throughout the pedestal, thus avoiding large scale transport events which span the full extent of that region. We explore different grain injection parameters to find an optimal SMBI scenario. We show that shallow SMBI deposition is sufficient for ELM mitigation.

The 4 th KSTAR campaign in 2011 concentrated on active ELM control by various methods such as non-axisymmetric magnetic perturbations, supersonic molecular beam injection (SMBI), vertical jogs of the plasma column, and edge electron heating. The segmented in-vessel control coil (IVCC) system is capable of applying n≤2 perturbed field with different phasing among top, middle, and bottom coils. Application of an n=1 perturbed field showed desirable ELM suppression result. Fast vertical jogs of the plasma column achieved ELM pace making and ELMs locked to 50 Hz vertical jogs were observed with a high probability of phase locking. A newly installed SMBI system was utilized for ELM control and a state of mitigated ELMs was sustained by the optimized repetitive SMBI pulse for a few tens of ELM periods. A change of ELM behavior was seen due to edge electron heating although the effect of ECH launch needs supplementary analyses. The ECEI images of suppressed/mitigated ELM states showed apparent differences when compared to natural ELMy states. Further analyses are ongoing to explain the observed ELM control results.

Abstract. Significant experimental advances have been made on HL-2A tokamak along with substantial improvement and development of hardware. The three dimensional spectral structures of the low frequency zonal flow, the geodesic acoustic mode (GAM), and quasi-mode-like low frequency fluctuations have been observed simultaneously for the first time. In addition, the spectral structure of the density fluctuation at GAM frequency is also identified. A spontaneous particle transport barrier has been observed in Ohmic discharges without any external momentum input. The barrier is evidenced by particle perturbation study using modulated SMBI and microwave reflectometry. The non-local transport effect with new features induced by SMBI has been investigated. The e-fishbone instability excited by energetic electrons of non-Maxwellian distribution has been investigated via 10-channel CdTe hard x-ray detector. It is found that the e-fishbone is correlated with the existence of energetic electrons of 30-70 keV. The experiment shows that the suppression of m/n = 2/1 tearing modes can be sustained by ECRH with low modulation frequency of about 10 Hz. Extended confinement improvement is obtained after the mode suppression.

Since the first H-mode discharges in 2010, the duration of the H-mode state has been extended and a significantly wider operational window of plasma parameters has been attained. Using a second neutral beam (NB) source and improved tuning of equilibrium configuration with real-time plasma control, a stored energy of W tot ∼ 450 kJ has been achieved with a corresponding energy confinement time of τ E ∼ 163 ms. Recent discharges, produced in the fall of 2012, have reached plasma β N up to 2.9 and surpassed the n = 1 ideal no-wall stability limit computed for H-mode pressure profiles, which is one of the key threshold parameters defining advanced tokamak operation. Typical H-mode discharges were operated with a plasma current of 600 kA at a toroidal magnetic field B T = 2 T. L-H transitions were obtained with 0.8-3.0 MW of NB injection power in both single-and double-null configurations, with H-mode durations up to ∼15 s at 600 kA of plasma current. The measured power threshold as a function of lineaveraged density showed a roll-over with a minimum value of ∼0.8 MW at ne ∼ 2×10 19 m −3 . Several edge-localized mode (ELM) control techniques during H-mode were examined with successful results including resonant magnetic perturbation, supersonic molecular beam injection (SMBI), vertical jogging and electron cyclotron current drive injection into the pedestal region. We observed various ELM responses, i.e. suppression or mitigation, depending on the relative phase of in-vessel control coil currents. In particular, with the 90 • phase of the n = 1 RMP as the most resonant configuration, a complete suppression of type-I ELMs was demonstrated. In addition, fast vertical jogging of the plasma column was also observed to be effective in ELM pace-making. SMBI-mitigated ELMs, a state of mitigated ELMs, were sustained for a few tens of ELM periods. A simple cellular automata ('sand-pile') model predicted that shallow deposition near the pedestal foot induced small-sized high-frequency ELMs, leading to the mitigation of large ELMs. In addition to the ELM control experiments, various physics topics were explored focusing on ITER-relevant physics issues such as the alteration of toroidal rotation caused by both electron cyclotron resonance heating (ECRH) and externally applied 3D fields, and the observed rotation drop by ECRH in NB-heated plasmas was investigated in terms of either a reversal of the turbulence-driven residual stress due to the transition of ion temperature gradient to trapped electron mode turbulence or neoclassical toroidal viscosity (NTV) torque by the internal kink mode. The suppression of runaway electrons using massive gas injection of deuterium showed that runaway electrons were avoided only below 3 T in KSTAR. Operation in 2013 is expected to routinely exceed the n = 1 ideal MHD no-wall stability boundary in the long-pulse H-mode ( 10 s) by applying real-time shaping control, enabling n = 1 resistive wall mode active control studies. In addition, intensive works for ELM mitigation, ELM dynamics, toroidal ro...

We report on model studies of stimulated L→H transitions. These studies use a novel reduced mesoscale model. Studies reveal that L→H transitions can be triggered by particle injection into a subcritical state (i.e., P