Density profiles in pedestal region (H-mode) are measured in HL-2A and the characteristics of the density pedestal are described. Cold particle deposition by Supersonic Molecular Beam Injection (SMBI) within the pedestal is verified. ELM mitigation by SMBI into the H-mode pedestal is demonstrated and the relevant physics is elucidated. The sensitivity of the effect to SMBI pressure and duration are studied. Following SMBI, the ELM frequency increases and ELM amplitude decreases for a finite duration period. Increases in ELM frequency of SMBI ELM f / 0 ELM f 2-3.5 are achieved. This experiment argues that the ELM mitigation results from an increase in Page 2 higher frequency fluctuations and transport events in the pedestal, which are caused by SMBI. These inhibit the occurrence of large transport events which span the entire pedestal width. The observed change in the density pedestal profiles and edge particle flux spectrum with and without SMBI supports this interpretation. An analysis of the experiment and a model shows that ELMs can be mitigated by SMBI with shallow particle penetration into the pedestal.

The experimental results of low pressure supersonic molecular beam injection (SMBI) fuelling on the HL-2A closed divertor indicate that during the period of pulsed SMBI the power density convected at the target plate surfaces was 0.4 times of that before or after the beam injection. An empirical scaling law used for the SMBI penetration depth for the HL-2A plasma was obtained. The cluster jet injection (CJI) is a new fuelling method which is based on and developed from the experiments of SMBI in the HL-1M tokamak. The hydrogen clusters are produced at liquid nitrogen temperature in a supersonic adiabatic expansion of moderate backing pressure gases into vacuum through a Laval nozzle and are measured by Rayleigh scattering. The measurement results have shown that the averaged cluster size of as large as hundreds of atoms was found at the backing pressures of more than 0.1 MPa. Multifold diagnostics gave coincidental evidence that when there was hydrogen CJI in the HL-2A plasma, a great deal of particles from the jet were deposited at a terminal area rather than uniformly ablated along the injecting path. SMB with clusters, which are like micro-pellets, will be of benefit for deeper fuelling, and its injection behaviour was somewhat similar to that of pellet injection. Both the particle penetration depth and the fuelling efficiency of the CJI were distinctly better than that of the normal SMBI under similar discharge operation. During hydrogen CJI or high-pressure SMBI, a combination of collision and radiative stopping forced the runaway electrons to cool down to thermal velocity due to such a massive fuelling.

We report recent experimental results from HL-2A and KSTAR on ELM mitigation by supersonic molecular beam injection (SMBI). Cold particle deposition within the pedestal by SMBI is verified in both machines.The signatures of ELM mitigation by SMBI are an ELM frequency increase and ELM amplitude decrease.These persist for an SMBI influence time τI. Here, τI is the time for the SMBI influenced pedestal profile to refill. An increase in f SMBI ELM /f 0 ELM and a decrease in the energy loss per ELM WELM were achieved in both machines. Physical insight was gleaned from studies of density and vφ(toroidal rotation velocity) evolution, particle flux and turbulence spectra, divertor heat load. The characteristic gradients of the pedestal density soften and a change in vφwas observed during a τI time. The spectra of the edge particle flux Г~ < ˜vr˜ne> and density fluctuation with and without SMBI were measured in HL-2A and in KSTAR, respectively. A clear phenomenon observed is the decrease in divertor heat load during the τI time in HL-2A. Similar results are the profiles of saturation current density Jsat with and without SMBI in KSTAR. We note that τI/τp (particle confinement time) is close to ~1, although there is a large difference in individual τI between the two machines. This suggests that τI is strongly related to particle-transport events. Experiments and analysis of a simple phenomenological model support the important conclusion that ELM mitigation by SMBI results from an increase in higher frequency fluctuations and transport events in the pedestal.

We construct a diffusive, bi-stable cellular automata model to elucidate the physical mechanisms underlying observed edge localized mode (ELM) mitigation by supersonic molecular beam injection (SMBI). The extended cellular automata model reproduces key qualitative features of ELM mitigation experiments, most significantly the increase in frequency of grain ejection events (ELMs), and the decrease in the number of grains ejected by these transport events. The basic mechanism of mitigation is the triggering of small scale pedestal avalanches by additional grain injection directly into the H-mode pedestal. The small scale avalanches prevent the gradient from building-up to marginality throughout the pedestal, thus avoiding large scale transport events which span the full extent of that region. We explore different grain injection parameters to find an optimal SMBI scenario. We show that shallow SMBI deposition is sufficient for ELM mitigation.