It is actual now to work out new radiation protecting sheeting on the basis of non-curing polymeric composition which possess self-adhesion properties, are easily mounted and dismantled and provide high tightness and low permeability. Mechanical properties of non-curing composites consisting of ethylene propylene diene monomer (EPDM), industrial oil (IO), alkyl phenol-formaldehyde resin (PF) with addition of barite (52 %) to the total material volume were investigated in this article. The aim of investigation is to find optimal content of the above mentioned components at which it would be possible to get the following properties: composite would be sticky enough (peel strength not less than 4 N/cm); character of a separation would be cohesive (on a material) and thus there would be no migration of softener and satisfactory resistance of fluidity. The results showed that PF addition till 20 % in the system EPDM/PF leads to the increasing of adhesive strength, in this case optimal oil concentration in the system EPDM/PF/IO is in the interval from 45 till 55 %. New self-adhesion lead-free material, exhibited higher X-ray-shielding properties, is also received in the result of investigation.
Аннотация. В статье представлены результаты исследований по подбору состава битумнокаучукового вяжущего вибропоглощающего покрытия. Применение вибропоглощающих покрытий тонкостенных строительных конструкций позволяет значительно снизить негативные вибрации. Существующие битумные и битумно-каучуковые материалы обладают недостаточным вибропоглощением в диапазоне отрицательных температур, что недопустимо в климатических условиях России. Подбор состава битумно-каучукового вяжущего и установление зависимости его свойств позволят получить материал с широким температурным диапазоном применения. В качестве объекта исследования была выбрана полимерная матрица, представляющая собой смесь двух материалов-бутилкаучука и битума, пластифицированную маслом индустриальным И-20А; наполнитель-мел марки МТД-2. Представлена зависимость физикомеханических свойств материала от содержания битум:бутилкаучук в смеси. Установлено, что материал на основе полученного вяжущего обладает эффективным вибродемпфированием в диапазоне температур от −40 до +40 °С. Ключевые слова: вибропоглощающее покрытие; битум; каучук; физико-механические свойства; температура Уже более 20 лет в авто-, машиностроении и строительстве широко применяются вибропоглощающие материалы листового типа на основе битума [1, 2]. В настоящее время широко распространены покрытия на битумно-каучуковом вяжущем [3, 4].
Данная работа посвящена проблеме разработки вибропоглощающих полимерных материалов, эффективных в широком температурно-частотном диапазоне. В связи с тем, что эффективность демпфирования колебаний в композите главным образом определяется свойствами полимерной матрицы, изучение ее свойств в зависимости от типа и количества структурообразующих параметров является актуальной задачей. Цель статьи заключается в определении изменений динамических свойств этиленвинилацетата при добавлении в него пластификаторов различной полярности и концентрации. Ведущим методом к исследованию данной проблемы является метод динамического механического анализа, позволяющий получить информацию об изменении механических характеристик под действием динамической нагрузки и контролируемой температуры и частоты. С помощью выявленных закономерностей удалось определить тип пластификатора, существенно снижающего температуру стеклования этиленвинилацетата. Установлено процентное соотношение системы этиленвинилацетат/пластификатор и, соответственно выявлен тип пластификатора, при котором максимум механических потерь принимает наибольшие значения. Определена степень полярности пластификатора, при которой эффективность пластификатора на этиленвинилацетат наибольшая. Полученные зависимости могут быть использованы в качестве исходных данных для аналитического прогнозирования динамических механических свойств композитов. Ключевые слова: этиленвинилацетат, диоктилфталат, хлорпарафин, индустриальное масло, модуль упругости, тангенс угла механических потерь, температура. Информация об авторах Волоцкой Алексей Николаевич, аспирант кафедры строительных конструкций и машин.
The article presents the results of a study of impact strength of underground cement materials with different water content activated by mixing water with the addition of high range plasticizers, biocidal agents, pigments, ground quartz, silica fume and fine aggregate. Samples for testing are formed in plates of size 150×100×10 mm. Testing was conducted at impact drop-weight method ASTM D7136. The maximum contact force, contact duration and magnitude of the pulse of the drummer were considered as the test parameters. The good results of the studied parameters showed highly filled plasticized compositions of the new generation. The use of iron oxide with yellow and green glauconitic pigments allows obtaining good results. Activation of the mixing water led to a rise in the maximum contact force in the case of the processing mode of E+М (3–3) while reducing the duration of the contact and the magnitude of the impulse. During the test of the biocidal composites with different biocidal preparations, it was established that the best indicators of the impact strength correspond to materials with the addition of «Teflex Antiplesen».
Non-curing sealants have a complex composition consisting of a mixture of polymers, plasticizers, extenders, adhesive additives, various special purpose additives (pigments, biocides, fire-retardants), and therefore the optimization of their compositions to improve the physical and mechanical and technological characteristics is rather complicated. This article demonstrates the experimental results of physical and mechanical properties such as penetration, strength, density, adhesion to metal and concrete, water absorption, and elongation of sealants on the basis of butyl-rubber and EPDM, depending on filler type and volume. The basic regularities of the nature influence and fillers on the physical and mechanical and technological characteristics of sealants are revealed. We’ve identified the ultimate proportion of fillers when the sealants meet the required specifications. The research results are the recommendations on the selection and optimization of the filler content of the sealant composition.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.