Due to its non-toxicity and environmentally friendly nature, carbohydrate-based fatty acid (CFA) esters are encouragingly used as antimicrobials and synthetic intermediates. They also are notably applied in food, surfactant, and pharmaceutical industries. In this respect, methyl 2,6-di-O-isopentanoyl-α-D-glucopyranoside (2), synthesized in a single step from methyl α-D-glucopyranoside (1), was converted into four other 3,4-di-O-acyl esters (3 – 6). All the newly synthesized CFA esters (2 – 6) were applied for the first time to study decay resistances of aspen (Populus tremula) and pine (Pinus sibirica) wood from decay caused by white-rot (Polyporous versicolor L.ex. Fr.) and brown-rot (Postia placenta (Fr). Cke.) fungi. Most of these CFA esters protected these woods from fungal attack, reduced deterioration, and preserved the weight percentage of woods at a certain point. It is noted that the CFA esters compounds reduced the deterioration and suppressed the weight percentage loss of wood at a certain point and from low to moderate decay resistances against the selected fungi.
This paper presents a new hybrid energy dissipation device and investigates experimentally its capability to improve the seismic response of an inherently very flexible structural system: a reinforced concrete waffle-flat plate structure. The new device combines in parallel within a single device a low-cost viscoelastic (VE) component and a metallic yielding (MY) component. The device has a gap that prevents deformations on the MY component in the range of displacements caused by wind or low intensity earthquakes, to avoid high-cycle fatigue damage. The MY component is expected to activate under the design or the maximum credible earthquake, providing the main structure with lateral stiffness, and a reliable and large source of energy dissipation capacity. Six new hybrid energy dissipation devices (energy dissipation system) were installed in a scaled two-story portion of a prototype RC waffle-flat plate structure (main structure) designed only for gravity loads, without considering special ductility detailing or capacity design rules for the columns. The VE component of the hybrid energy dissipation devices reduced the translational periods with largest effective modal mass along the horizontal directions X and Y to 60%, and increased the fraction of damping to about 12%. The main structure with the energy dissipation system was subjected to bidirectional shake table tests that represented frequent, design and maximum credible earthquakes. In the tests, the main structure remained basically undamaged under the frequent and the design earthquakes, whereas it suffered minor (reparable) damage under the maximum credible earthquake. The MY component remained undeformed under low intensity earthquakes.
Аннотация. В статье представлены результаты исследований по подбору состава битумнокаучукового вяжущего вибропоглощающего покрытия. Применение вибропоглощающих покрытий тонкостенных строительных конструкций позволяет значительно снизить негативные вибрации. Существующие битумные и битумно-каучуковые материалы обладают недостаточным вибропоглощением в диапазоне отрицательных температур, что недопустимо в климатических условиях России. Подбор состава битумно-каучукового вяжущего и установление зависимости его свойств позволят получить материал с широким температурным диапазоном применения. В качестве объекта исследования была выбрана полимерная матрица, представляющая собой смесь двух материалов-бутилкаучука и битума, пластифицированную маслом индустриальным И-20А; наполнитель-мел марки МТД-2. Представлена зависимость физикомеханических свойств материала от содержания битум:бутилкаучук в смеси. Установлено, что материал на основе полученного вяжущего обладает эффективным вибродемпфированием в диапазоне температур от −40 до +40 °С. Ключевые слова: вибропоглощающее покрытие; битум; каучук; физико-механические свойства; температура Уже более 20 лет в авто-, машиностроении и строительстве широко применяются вибропоглощающие материалы листового типа на основе битума [1, 2]. В настоящее время широко распространены покрытия на битумно-каучуковом вяжущем [3, 4].
This research is devoted to the actual problem of the development of damping polymer materials which are effective in a wide range of temperatures and having satisfactory strength characteristics. There are many works devoted to the study of dynamic mechanical properties of filled composites, but most do not take into account the influence of plasticizer on the strength properties of the polymer, as they change its characteristics for the worse. In this respect, the study and comparison of the mechanical properties of the polymer base with the introduction of different types and concentrations of plasticizers is an urgent task. According to the received regularities it was possible to define the type, concentration and boundaries of the polarity of the plasticizer, which reduces the strength characteristics of ethylene-vinyl acetate to a lesser degree.
Данная работа посвящена проблеме разработки вибропоглощающих полимерных материалов, эффективных в широком температурно-частотном диапазоне. В связи с тем, что эффективность демпфирования колебаний в композите главным образом определяется свойствами полимерной матрицы, изучение ее свойств в зависимости от типа структурообразующих параметров является актуальной задачей. Цель статьи заключается в определении изменений динамических свойств этиленвинилацетата при добавлении в него наполнителей различного типа. Ведущим методом исследования данной проблемы является метод динамического механического анализа, позволяющий получить информацию об изменении динамических характеристик под действием динамической нагрузки и контролируемой температуры и частоты. С помощью выявленных закономерностей удалось определить тип наполнителя, существенно смещающего температуру стеклования пластифицированного этиленвинилацетата в сторону положительных температур. Выявлен тип наполнителя, при котором максимум механических потерь принимает наибольшие значения. Полученные зависимости могут быть использованы в качестве исходных данных для аналитического прогнозирования динамических механических свойств композитов, а также для разработки вибропоглощающих полимерных композиционных материалов на основе этиленвинилацетата, эффективных в широком диапазоне температур. Ключевые слова: этиленвинилацетат, слюда, тальк, технический углерод, динамические свойства, наполнительThis article is devoted to the actual problem of the development of damping polymer materials which are effective in a wide range of working capacity. Effectiveness of a vibration damping in a composite is mainly defined by properties of a polymeric matrix, that's why studying of its properties depending on type of gel-forming parameters is an urgent task. The purpose of this article is to determine the changes in the dynamic properties of the polymer ethylene-vinyl acetate with the addition of fillers in it various type. The leading method to investigate this problem is the method of dynamic mechanical analysis, which allows to obtain information about changes in dynamic characteristics under the influence of dynamic load and controlled temperature. According to the received regularities it was possible to define the filler type significantly displaces glass transition of plasticized ethylenevinyl acetate towards positive temperatures. The type of filler is established at which the maximum of mechanical losses assumes high values. The received dependences can be used as input data for analytical prediction of dynamic mechanical properties of composites, as well as for the development of damping polymer composite materials based on ethylene-vinyl acetate, effective in a wide temperature range.
Данная работа посвящена проблеме разработки вибропоглощающих полимерных материалов, эффективных в широком температурно-частотном диапазоне. В связи с тем, что эффективность демпфирования колебаний в композите главным образом определяется свойствами полимерной матрицы, изучение ее свойств в зависимости от типа и количества структурообразующих параметров является актуальной задачей. Цель статьи заключается в определении изменений динамических свойств этиленвинилацетата при добавлении в него пластификаторов различной полярности и концентрации. Ведущим методом к исследованию данной проблемы является метод динамического механического анализа, позволяющий получить информацию об изменении механических характеристик под действием динамической нагрузки и контролируемой температуры и частоты. С помощью выявленных закономерностей удалось определить тип пластификатора, существенно снижающего температуру стеклования этиленвинилацетата. Установлено процентное соотношение системы этиленвинилацетат/пластификатор и, соответственно выявлен тип пластификатора, при котором максимум механических потерь принимает наибольшие значения. Определена степень полярности пластификатора, при которой эффективность пластификатора на этиленвинилацетат наибольшая. Полученные зависимости могут быть использованы в качестве исходных данных для аналитического прогнозирования динамических механических свойств композитов. Ключевые слова: этиленвинилацетат, диоктилфталат, хлорпарафин, индустриальное масло, модуль упругости, тангенс угла механических потерь, температура. Информация об авторах Волоцкой Алексей Николаевич, аспирант кафедры строительных конструкций и машин.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.