Due to its potential for multi-gigabit and low latency wireless links, millimeter wave (mmWave) technology is expected to play a central role in 5th generation (5G) cellular systems. While there has been considerable progress in understanding the mmWave physical layer, innovations will be required at all layers of the protocol stack, in both the access and the core network. Discrete-event network simulation is essential for end-to-end, cross-layer research and development. This paper provides a tutorial on a recently developed full-stack mmWave module integrated into the widely used open-source ns-3 simulator. The module includes a number of detailed statistical channel models as well as the ability to incorporate real measurements or raytracing data. The Physical (PHY) and Medium Access Control (MAC) layers are modular and highly customizable, making it easy to integrate algorithms or compare Orthogonal Frequency Division Multiplexing (OFDM) numerologies, for example. The module is interfaced with the core network of the ns-3 Long Term Evolution (LTE) module for full-stack simulations of end-to-end connectivity, and advanced architectural features, such as dualconnectivity, are also available. To facilitate the understanding of the module, and verify its correct functioning, we provide several examples that show the performance of the custom mmWave stack as well as custom congestion control algorithms designed specifically for efficient utilization of the mmWave channel.This work has been submitted to IEEE Communication Surveys and Tutorials for possible publication.

Abstract-The IMT 2020 requirements of 20 Gbps peak data rate and 1 millisecond latency present significant engineering challenges for the design of 5G cellular systems. Use of the millimeter wave (mmWave) bands above 10 GHz -where vast quantities of spectrum are available -is a promising 5G candidate that may be able to rise to the occasion.However, while the mmWave bands can support massive peak data rates, delivering these data rates on end-to-end service while maintaining reliability and ultra-low latency performance will require rethinking all layers of the protocol stack. This papers surveys some of the challenges and possible solutions for delivering end-to-end, reliable, ultra-low latency services in mmWave cellular systems in terms of the Medium Access Control (MAC) layer, congestion control and core network architecture.

Due to the heavy reliance of millimeter-wave (mmWave) wireless systems on directional links, beamforming (BF) with high-dimensional arrays is essential for cellular systems in these frequencies.How to perform the array processing in a power efficient manner is a fundamental challenge. Analog and hybrid BF require fewer analog-to-digital and digital-to-analog converters (ADCs and DACs), but can only communicate in a small number of directions at a time, limiting directional search, spatial multiplexing and control signaling. Digital BF enables flexible spatial processing, but must be operated at a low quantization resolution to stay within reasonable power levels. This decrease in quantizer resolution introduces noise in the received signal and degrades the quality of the transmitted signal.To assess the effect of low-resolution quantization on cellular system, we present a simple additive white Gaussian noise (AWGN) model for quantization noise. Simulations with this model reveal that at moderate resolutions (3-4 bits per ADC), there is negligible loss in downlink cellular capacity from quantization. In essence, the low-resolution ADCs limit the high SNR, where cellular systems typically do not operate. For the transmitter, it is shown that DACs with 4 or more bits of resolution do not violate the adjacent carrier leakage limit set by 3 rd Generation Partnership Project (3GPP) New Radio (NR) standards for cellular operations. Further, this work studies the effect of low resolution quantization on the error vector magnitude (EVM) of the transmitted signal.In fact, our findings suggests that low-resolution fully digital BF architectures can be a power efficient alternative to analog or hybrid beamforming for both transmitters and receivers at millimeter wave. 2 Millimeter wave, 5G cellular, Low resolution quantizers, Digital beamforming.

No abstract

The increasing demand of data, along with the spectrum scarcity, are motivating a urgent shift towards exploiting new bands. This is the main reason behind identifying mmWaves as the key disruptive enabling technology for 5G cellular networks. Indeed, utilizing new bands means facing new challenges; in this context, they are mainly related to the radio propagation, which is shorter in range and more sensitive to obstacles. The resulting key aspects that need to be taken into account when designing mmWave cellular systems are directionality and link intermittency. The lack of network level results motivated this work, which aims at providing the first of a kind open source mmWave framework, based on the network simulator ns-3. The main focus of this work is the modeling of customizable channel, physical (PHY) and medium access control (MAC) layers for mmWave systems. The overall design and architecture of the model are discussed in details. Finally, the validity of our proposed framework is corroborated through the simulation of a simple scenario.

The millimeter-wave (mmWave) frequencies have attracted considerable attention for fifth generation (5G) cellular communication as they offer orders of magnitude greater bandwidth than current cellular systems. However, the medium access control (MAC) layer may need to be significantly redesigned to support the highly directional transmissions, ultra-low latencies and high peak rates expected in mmWave communication. To address these challenges, we present a novel mmWave MAC layer frame structure with a number of enhancements including flexible, highly granular transmission times, dynamic control signal locations, extended messaging and ability to efficiently multiplex directional control signals.Analytic formulae are derived for the utilization and control overhead as a function of control periodicity, number of users, traffic statistics, signal-to-noise ratio and antenna gains. Importantly, the analysis can incorporate various front-end MIMO capability assumptions -a critical feature of mmWave. Under realistic system and traffic assumptions, the analysis reveals that the proposed flexible frame structure design offers significant benefits over designs with fixed frame structures similar to current 4G long-term evolution (LTE). It is also shown that fully digital beamforming architectures offer significantly lower overhead compared to analog and hybrid beamforming under equivalent power budgets. 5G cellular systems, millimeter wave, frame structure, radio resource utilization, control overhead. Index Terms

The growing demand for ubiquitous mobile data services along with the scarcity of spectrum in the sub-6 GHz bands has given rise to the recent interest in developing wireless systems that can exploit the large amount of spectrum available in the millimeter wave (mmWave) frequency range. Due to its potential for multi-gigabit and ultra-low latency links, mmWave technology is expected to play a central role in 5th Generation (5G) cellular networks. Overcoming the poor radio propagation and sensitivity to blockages at higher frequencies presents major challenges, which is why much of the current research is focused at the physical layer. However, innovations will be required at all layers of the protocol stack to effectively utilize the large air link capacity and provide the end-to-end performance required by future networks.Discrete-event network simulation will be an invaluable tool for researchers to evaluate novel 5G protocols and systems from an end-to-end perspective. In this work, we present the first-of-its-kind, open-source framework for modeling mmWave cellular networks in the ns-3 simulator. Channel models are provided along with a configurable physical and MAC-layer implementation, which can be interfaced with the higher-layer protocols and core network model from the ns-3 LTE module to simulate end-to-end connectivity. The framework is demonstrated through several example simulations showing the performance of our custom mmWave stack.

Future millimeter-wave systems, 5G cellular or WiFi, must rely on highly directional links to overcome severe pathloss in these frequency bands. Establishing such links requires the mutual discovery of the transmitter and the receiver, potentially leading to a large latency and high energy consumption. In this work, we show that both the discovery latency and energy consumption can be significantly reduced using fully digital front-ends. In fact, we establish that by reducing the resolution of the fully digital front-ends we can achieve lower energy consumption compared to both analog and high-resolution digital beamforming. Since beamforming through analog front-ends allows sampling in only one direction at a time, the mobile device is “on” for a longer time compared to a digital beamformer, which can get spatial samples from all directions in one shot. We show that the energy consumed by the analog front-end can be four to six times more than that of the digital front-ends, depending on the size of the employed antenna arrays. We recognize, however, that using fully digital beamforming post beam discovery, i.e., for data transmission, is not viable from a power consumption standpoint. To address this issue, we propose the use of digital beamformers with low-resolution analog to digital converters (4 bits). This reduction in resolution brings the power consumption to the same level as analog beamforming for data transmissions while benefiting from the spatial multiplexing capabilities of fully digital beamforming, thus reducing initial discovery latency and improving energy efficiency.