Bacterial Cellulose (BC) synthesized by Acetobacter xylinum has been a promising candidate for medical applications. Modifying BC to possess the properties needed for specific applications has been reported. In this study, BCs functionalized by organosilanes were hypothesized to improve the attachment and spreading of Normal Human Dermal Fibroblast (NHDF). The BC gels obtained from biosynthesis were dried by either ambient-air drying or freeze drying. The surfaces of those dried BCs were chemically modified by grafting methyl terminated octadecyltrichlorosilane (OTS) or amine terminated 3-aminopropyltriethoxysilane (APTES) to expectedly increase hydrophobic or electrostatic interactions with NHDF cells, respectively. NHDF cells improved their attachment and spreading on the majority of APTES-modified BCs (∼70-80% of area coverage by cells) with more rapid growth (∼2.6-2.8× after incubations from 24 to 48h) than on tissue culture polystyrene (∼2×); while the inverse results (< 5% of area coverage and stationary growth) were observed on the OTS-modified BCs. For organosilane modified BCs, the drying method had no effect on in vitro cell attachment/spreading behaviors.

A nanocellulose-gelatin (bacterial cellulose gelatin (BCG)) film was developed by a supplement of gelatin, at a concentration of 1%–10% w/v, in a coconut-water medium under the static cultivation of Acetobacter xylinum. The two polymers exhibited a certain degree of miscibility. The BCG film displayed dense and uniform homogeneous structures. The Fourier transform infrared spectroscopy (FTIR) results demonstrated interactions between the cellulose and gelatin. Incorporation of gelatin into a cellulose nanofiber network resulted in significantly improved optical transparency and water absorption capacity of the films. A significant drop in the mechanical strengths and a decrease in the porosity of the film were observed when the supplement of gelatin was more than 3% (w/v). The BCG films showed no cytotoxicity against Vero cells.

Bacterial cellulose (BC) films containing an ethanolic extract of mangosteen peel were prepared and their physical, chemical, and anticancer properties were characterized. The cumulative absorption and release profiles of bioactive compounds in the films were determined based on total phenolic and α-mangostin content. The BC films were filled with total phenolic compounds expressed as gallic acid equivalent varying from 4.72 to 275.91 mg/cm3 dried film, and α-mangostin varying from 2.06 to 248.20 mg/cm3 dried film. A Fourier transform infrared spectroscopy evaluation showed that there were weak interactions between the functional groups of the extract and the BC. Decreases in the water absorption capacity and water vapor transmission rate of the modified films were detected. Release studies were performed using Franz diffusion cells. In a non-transdermal system, the release of bioactive compounds from the films depended on concentration, immersion time, and the pH of the dissolution medium. A transdermal diffusion study showed that 59-62% of total phenolic compounds that were initially loaded were released from the films and more than 95% of bioactive compounds released from the films were adsorbed into pig skin. Only very small amount of the bioactive compounds penetrated through pig skin and into phosphate and acetate buffers. In studies of anticancer abilities, the release of 2.0 μg/ml α-mangostin from the BC films could suppress the growth of B16F10 melanoma (approximately 31% survival). With the release of α-mangostin at greater than 17.4-18.4 μg/ml, less than 15 and 5% survival of B16F10 melanoma and MCF-7 breast cancer cells, respectively, was observed.

No abstract

Curcumin-loaded bacterial cellulose films were developed in this study. Curcumin was absorbed into never-dried bacterial cellulose pellicles by 24-h immersion in solutions of curcumin in the range of 0.2-1.0 mg /mL. The curcumin-loaded bacterial cellulose pellicles were then air-dried and characterized. The mechanical properties of curcumin-loaded bacterial cellulose films, particularly the stretching properties, appeared to be lower than those of bacterial cellulose film. This was especially evident when the loading concentration of curcumin was higher than 0.4 mg/mL. Fourier-transform infrared spectroscopy analysis indicated an interaction between bacterial cellulose microfibrils and curcumin. Controlled release of curcumin was achieved in buffer solutions containing Tween 80 and methanol additives, at pH 5.5 and 7.4. Curcumin-loaded bacterial cellulose films prepared with curcumin solutions at concentrations of 0.5 and 1.0 mg/mL displayed antifungal activities against Aspergillus niger. They also exhibited anticancer activity against A375 malignant melanoma cells. No significant cytotoxic effect was observed against normal dermal cells, specifically, human keratinocytes and human dermal fibroblasts.

No abstract

No abstract

Natural rubber (NR) reinforced with high loading of microfibrillated cellulose (MFC) was fabricated in the presence of sodium alginate as a thickening and dispersing agent in NR latex. The tensile strength and Young’s moduli of the 50% wt. MFC loading-NR composites were 13.6 and 1085.7 MPa, which were about 11.3- and 329-times enhanced compared with those of the neat NR film. The maximum elongation at 313.3% was obtained from 30% MFC loading, which was a 3.3-fold increase of that of the NR film. The thermal stability of MFC–NR films was slightly reduced, while the glass transition temperature remained unchanged at −64 °C. The MFC–NR films exhibited high water adsorption ability, toluene resistance, and biodegradability.