Over 20 million burn injuries are reported every year, with severe cases requiring skin grafting. Traditionally, split thickness skin grafts are prepared by excising a small portion of healthy skin and its incision patterning using a suitable meshing device, which allows the graft to be expanded beyond its capacity. To date, the maximum expansion achieved through skin grafting has been reported to be less than three times, which is not sufficient for covering large burn sites with limited donor site skin. In this work, we have attempted to study skin graft expansion potential with novel auxetic patterns, which are known to exhibit negative Poisson's effect. Two‐layer skin graft models were developed using eight different auxetic incision patterns, and subjected to uniaxial and biaxial tensile strains. The Poisson's ratio, meshing ratio, and induced stresses were characterized for all graft models. The numerical results indicated expansion potentials greater than that of traditional skin grafts across all loads. Extremely high expansions (i.e., >30 times) were estimated for the I‐Shaped Re‐entrant and Rotating Triangles shaped auxetic models without rupture. Such pioneering findings are anticipated to initiate ground‐breaking advances towards skin graft research and improved outcomes in burn surgeries.
The development of foot ulcers is a common consequence of severe diabetes. Due to vascular disorders and impeded healing caused by the disease, most foot ulcers have been reported to be affected by body weight and progress with time. Also, abnormal distribution of plantar pressures has been observed to cause the formation of additional ulcers, which may collectively lead to traumatic amputations. While a study of such pathophysiology is not possible through experiments, a few computational modelling works have investigated diabetic foot ulcers. To date, ulcers with a few sizes and locations have been studied, and their effect on the plantar stresses has been quantified. In this work, we have attempted to study the effect of all possible ulcer locations on the generated plantar peak stresses and peak stress locations where additional ulcers may form. Also, the effect of ulcer location on the possible ulcer growth was investigated. A full-scale foot model was developed and a total of 52 ulcer locations were simulated separately, with standing and walking loads. The generated stresses were normalised with the foot size and statistically analysed to develop novel formulations for predicting peak plantar stresses and their locations for any known ulcer location. The results from this study are anticipated to provide important guidelines to doctors and medical practitioners for predicting foot ulcer progression in diabetic patients with existing ulcers and allow the administration of timely preventive interventions.
Plantar foot pain is one of the most common musculoskeletal conditions affecting the foot. It is regularly experienced by the population with occupations that require prolonged standing hours, especially in nurses. The etiology of plantar foot pain remains unclear, but it is likely to be multi-factorial, with many associated risk factors including increased hours of standing. Orthoses and insoles are often recommended to plantar foot pain patients, however with minimal scientific advancements and limited customizations. In this study, a novel 3D-printed multi-material customized foot orthosis was developed, and its effectiveness on plantar foot pain reduction and functional ability improvement was studied in the nursing population. A total of thirty-six subjects were recruited and were randomized into two groups. The experimental group received the novel 3D-printed multi-material customized foot orthosis, whereas the control group received the standard-of-care (or traditional) intervention. Pre-test and the post-test scores of pains, functional ability and plantar pressure were observed using SPSS software. Improvements were observed in both of the groups; however, better improvements were seen in the experimental group. Overall, the novel 3D printing-based customized foot orthosis showed significant efficacy in reducing plantar foot pain and pressure, and also in increasing functional ability in the nursing population as compared to the traditional method.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.