Graphene monolayer has been grown by chemical vapor deposition on copper and then suspended over a hole. By measuring the laser heating and monitoring the Raman G peak, we obtain room-temperature thermal conductivity and interface conductance of (370 + 650/-320) W/m K and (28 + 16/-9.2) MW/m(2) K for the supported graphene. The thermal conductivity of the suspended graphene exceeds (2500 + 1100/-1050) W/m K near 350 K and becomes (1400 + 500/-480) W/m K at about 500 K.

The ability to protect refined metals from reactive environments is vital to many industrial and academic applications. Current solutions, however, typically introduce several negative effects, including increased thickness and changes in the metal physical properties. In this paper, we demonstrate for the first time the ability of graphene films grown by chemical vapor deposition to protect the surface of the metallic growth substrates of Cu and Cu/Ni alloy from air oxidation. In particular, graphene prevents the formation of any oxide on the protected metal surfaces, thus allowing pure metal surfaces only one atom away from reactive environments. SEM, Raman spectroscopy, and XPS studies show that the metal surface is well protected from oxidation even after heating at 200 °C in air for up to 4 h. Our work further shows that graphene provides effective resistance against hydrogen peroxide. This protection method offers significant advantages and can be used on any metal that catalyzes graphene growth.

No abstract

Using micro-Raman spectroscopy, the thermal conductivity of a graphene monolayer grown by chemical vapor deposition and suspended over holes with different diameters ranging from 2.9 to 9.7 μm was measured in vacuum, thereby eliminating errors caused by heat loss to the surrounding gas. The obtained thermal conductivity values of the suspended graphene range from (2.6 ± 0.9) to (3.1 ± 1.0) × 10(3) Wm(-1)K(-1) near 350 K without showing the sample size dependence predicted for suspended, clean, and flat graphene crystal. The lack of sample size dependence is attributed to the relatively large measurement uncertainty as well as grain boundaries, wrinkles, defects, or polymeric residue that are possibly present in the measured samples. Moreover, from Raman measurements performed in air and CO(2) gas environments near atmospheric pressure, the heat transfer coefficient for air and CO(2) was determined and found to be (2.9 +5.1/-2.9) and (1.5 +4.2/-1.5) × 10(4) Wm(-2)K(-1), respectively, when the graphene temperature was heated by the Raman laser to about 510 K.

High-performance MoS transistors are developed using atomic hexagonal boron nitride as a tunneling layer to reduce the Schottky barrier and achieve low contact resistance between metal and MoS . Benefiting from the ultrathin tunneling layer within 0.6 nm, the Schottky barrier is significantly reduced from 158 to 31 meV with small tunneling resistance.

We report the use of free-standing, lightweight, and highly conductive ultrathin graphite foam (UGF), loaded with lithium iron phosphate (LFP), as a cathode in a lithium ion battery. At a high charge/discharge current density of 1280 mA g(-1), the specific capacity of the LFP loaded on UGF was 70 mAh g(-1), while LFP loaded on Al foil failed. Accounting for the total mass of the electrode, the maximum specific capacity of the UGF/LFP cathode was 23% higher than that of the Al/LFP cathode and 170% higher than that of the Ni-foam/LFP cathode. Using UGF, both a higher rate capability and specific capacity can be achieved simultaneously, owing to its conductive (∼1.3 × 10(5) S m(-1) at room temperature) and three-dimensional lightweight (∼9.5 mg cm(-3)) graphitic structure. Meanwhile, UGF presents excellent electrochemical stability comparing to that of Al and Ni foils, which are generally used as conductive substrates in lithium ion batteries. Moreover, preparation of the UGF electrode was facile, cost-effective, and compatible with various electrochemically active materials.

Millimeter-size single-crystal monolayer graphene is synthesized on polycrystalline Cu foil by a method that involves suppressing loss by evaporation of the Cu at high temperature under low pressure. This significantly diminishes the number of graphene domains, and large single crystal domains up to ∼2 mm in size are grown.

Controlling the thickness and uniformity during growth of multilayer graphene is an important goal. Here we report the synthesis of large-area monolayer and multilayer, particularly bilayer, graphene films on Cu-Ni alloy foils by chemical vapor deposition with methane and hydrogen gas as precursors. The dependence of the initial stages of graphene growth rate on the substrate grain orientation was observed for the first time by electron backscattered diffraction and scanning electron microscopy. The thickness and quality of the graphene and graphite films obtained on such Cu-Ni alloy foils could be controlled by varying the deposition temperature and cooling rate and were studied by optical microscopy, scanning electron microscopy, atomic force microscopy, and micro-Raman imaging spectroscopy. The optical and electrical properties of the graphene and graphite films were studied as a function of thickness.