Controlling the interactions between macrophages and biomaterials is critical for modulating the response to implants. While it has long been thought that biomaterial surface chemistry regulates the immune response, recent studies have suggested that material geometry may in fact dominate. Our previous work demonstrated that elongation of macrophages regulates their polarization towards a pro-healing phenotype. In this work, we elucidate how surface topology might be leveraged to alter macrophage cell morphology and polarization state. Using a deep etch technique, we fabricated titanium surfaces containing micro and nano-patterned grooves, which have been previously shown to promote cell elongation. Morphology, phenotypic markers, and cytokine secretion of murine bone marrow derived macrophages on different groove widths were analyzed. The results suggest that micro and nano-patterned grooves influenced macrophage elongation, which peaked on substrates with 400-500 nm wide grooves. Surface grooves did not affect inflammatory activation, but drove macrophages towards an anti-inflammatory, pro-healing phenotype. While secretion of TNF-alpha remained low in macrophages across all conditions, macrophages secreted significantly higher levels of anti-inflammatory cytokine, IL-10, on intermediate groove widths compared to cells on other Ti surfaces. Our findings highlight the potential of using surface topography to regulate macrophage function, and thus control the wound healing and tissue repair response to biomaterials.

Piezoelectricity-based energy harvesting from wasted mechanical energies has garnered an increasing attention as a clean energy source. Especially, flexible organic piezoelectric materials provide an opportunity to exploit their uses in the mechanically challenging areas where brittle inorganic counterparts have mechanical limitations. In this regard, electrospinning has shown its advantages of producing poly(vinylidene fluoride) (PVDF)-based nanofibrous structures without the necessity of a secondary processing to induce/increase piezoelectric properties. However, the effects of electrospun fiber dimension, one of the main morphological parameters in electrospun fibers, on piezoelectricity have not been fully understood. In this study, two dependent design of experiments (DOEs) were utilized to systematically control the dimensions of electrospun poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)) to produce nanofibers having their diameter ranging from 1000 to sub-100 nm. Such a dimensional reduction resulted in the increase of piezoelectric responsible electroactive phase content and the degree of crystallinity. These changes in crystal structure led to approximately 2-fold increase in piezoelectric constant as compared to typical P(VDF-TrFE) thin films. More substantially, the dimensional reduction also increased the Young's modulus of the nanofibers up to approximately 80-fold. The increases in piezoelectric constant and Young's modulus collectively enhanced piezoelectric performance, resulting in the exponential increase in electric output of nanofiber mats when the fiber diameters were reduced from 860 nm down to 90 nm.Taken together, the results suggest a new strategy to improve the piezoelectric performance of electrospun P(VDF-TrFE) via optimization of their electromechanical and mechanical properties.

The objective of this study was to investigate the adhesion and morphology of bone marrow derived stromal cells (BMSCs) on bulk titanium (Ti) substrates with precisely-patterned surfaces consisting of groove-based gratings with groove widths ranging from 50 micro m down to 0.5 micro m (500 nm). Although it is well known that certain surface patterning enhances osteoblast (bone-forming cell) functions, past studies on cell-pattern interactions reported in the literature have heavily relied on surface patterning on materials with limited clinical relevance for orthopedic applications, such as polymeric substrates. The clinical need for improving osseointegration and juxtaposed bone formation around load-bearing Ti implants motivated this in vitro study. BMSCs were selected as model cells due to their important role in bone regeneration. The results showed significantly greater BMSC adhesion density and more favorable cell morphology on sub-micropatterned gratings when compared with larger micropatterned gratings and non-patterned control surfaces after both 24 hr and 72 hr cultures. We observed increasing cellular alignment and elongation with decreasing feature size. We also identified two distinctive cellular morphologies: Type I-Attached and spread cells that elongated along the pattern axes; and Type II-Superficially adhered round cells. Sub-micropatterned gratings demonstrated significantly greater Type I cell density than the non-patterned control, and lower Type II cell density than the larger micropatterned gratings. Collectively, these results suggest potential for rationally designing nano-scale surface topography on Ti implants to improve osseointegration.

In this work, we evaluate the in vitro response of endothelial cells (EC) to variation in precisely-defined, micrometer to sub-micrometer scale topography on two different substrate materials, titanium (Ti) and silicon (Si). Both substrates possess identically-patterned surfaces composed of microfabricated, groove-based gratings with groove widths ranging from 0.5 to 50 µm, grating pitch twice the groove width, and groove depth of 1.3 µm. These specific materials are chosen due to their relevance for implantable microdevice applications, while grating-based patterns are chosen for the potential they afford for inducing elongated and aligned cellular morphologies reminiscent of the native endothelium. Using EA926 cells, a human EC variant, we show significant improvement in cellular adhesion, proliferation, morphology, and function with decreasing feature size on patterned Ti substrates. Moreover, we show similar trending on patterned Si substrates, albeit to a lesser extent than on comparably patterned Ti substrates. Collectively, these results suggest promise for sub-micrometer topographic patterning in general, and sub-micrometer patterning of Ti specifically, as a means for enhancing endothelialization and neovascularisation for novel implantable microdevice applications.

We have developed a scanning magnetic microscope (SMM) with 25 µm resolution in spatial position for the magnetic features of room temperature objects. The microscope consists of a high-temperature superconductor (HTS) dc SQUID sensor, suspended in vacuum with a self-adjusting standoff, close spaced liquid nitrogen Dewar, X -Y scanning stage and a computer control system. The HTS SQUIDs were optimized for better spatial and field resolutions for operation at liquid nitrogen temperature. Measured inside a magnetic shield, the 10 pT Hz −1/2 typical noise of the SQUIDs is white down to frequencies of about 10 Hz, increasing up to about 20 pT Hz −1/2 at 1 Hz. The microscope is mounted on actively damped platforms, which negate vibrations from the environment as well as damping internal stepper motor noises. A high-resolution video telescope and a 1 µm precision z-axis positioning system allow a close positioning of the sample under the sensor. The ability of the sensors to operate in unshielded environmental conditions with magnetic fields up to about 15 G allowed us to perform 2D mapping of the local ac and dc susceptibility of the objects.