Thermoelectric generators, which convert heat directly into electrical power, have great potentialities in the energy harvesting field. The exploitation of these potentialities is limited by the materials currently used, characterized by good thermoelectric properties, but also by several drawbacks. This work presents a silicon-based thermoelectric generator, made of a large collection of heavily p -doped silicon nanostructures. This macroscopic device (area of several mm 2 ) collects together the good thermoelectric features of silicon, in terms of high power factor, and a very reduced thermal conductivity, which resulted in being exceptionally low (1.8 W/(m K), close to the amorphous limit). The generated electrical power density is remarkably high for a Si-based thermoelectric generator, and it is suitable for scavenging applications which can exploit small temperature differences. A full characterization of the device (Seebeck coefficient, thermal conductivity, maximum power output) is reported and discussed.

A large amount of parallel silicon nanowires, placed perpendicularly to a silicon substrate (silicon nanowire forests), has been contacted and assembled in order to fabricate legs of a thermoelectric generator. This paper reports the measurement of the main parameter for thermoelectric applications, which is the thermal conductivity. The reported value, which confirms the strong reduction of the thermal conductivity in nanostructures, is measured on a large amount (> 10 7 ) of parallel nanowires with a diameter variable in the range 60 -120 nm, and takes into account eventual non uniformities which are unavoidable on surfaces of several mm 2 . As silicon nanowire forests are very thin, it has been necessary to develop a suitable measurement apparatus. The fabrication of devices based on silicon nanowire forests, the apparatus and the measurement procedure, as well as the the results, are illustrated and discussed.

The necessity to resolve the issue of rapid charge carrier recombination for boosting photocatalytic performance is a vigorous and challenging research field. To address this, the construction of a binary system of step-scheme (S-scheme) CuO@TiO2 heterostructure composite has been demonstrated through a facile solid-state route. The remarkably enhanced photocatalytic performance of CuO@TiO2, compared with single TiO2, which can consequence in the more efficient separation of photoinduced charge carriers, reduced the band gap of TiO2, improved the electrical transport performance, and improved the lifetimes, thus donating it with the much more powerful oxidation and reduction capability. A photocatalytic mechanism was proposed to explain the boosted photocatalytic performance of CuO@TiO2 on a complete analysis of physicochemical, DFT calculations, and electrochemical properties. In addition, this work focused on the investigation of the stability and recyclability of CuO@TiO2 in terms of efficiency and its physical origin using XRD, BET, and XPS. It is found that the removal efficiency diminishes 4.5% upon five recycling runs. The current study not only promoted our knowledge of the binary system of S-scheme CuO@TiO2 heterojunction composite photocatalyst but also shed new light on the design of heterostructure photocatalysts with high-performance and high stability.

No abstract

Microbial contamination is one of the major dreadful problems that raises hospitalization, morbidity and mortality rates globally, which subsequently obstructs socio-economic progress. The continuous misuse and overutilization of antibiotics participate mainly in the emergence of microbial resistance. To circumvent such a multidrug-resistance phenomenon, well-defined nanocomposite structures have recently been employed. In the current study, a facile, novel and cost-effective approach was applied to synthesize Ag@Ag2O core–shell nanocomposites (NCs) via chemical method. Several techniques were used to determine the structural, morphological, and optical characteristics of the as-prepared NCs. XRD, Raman, FTIR, XPS and SAED analysis revealed a crystalline hybrid structure of Ag core and Ag2O shell. Besides, SEM and HRTEM micrographs depicted spherical nanoparticles with size range of 19–60 nm. Additionally, zeta potential and fluorescence spectra illustrated aggregated nature of Ag@Ag2O NCs by − 5.34 mV with fluorescence emission peak at 498 nm. Ag@Ag2O NCs exhibited higher antimicrobial, antibiofilm, and algicidal activity in dose-dependent behavior. Interestingly, a remarkable mycocidal potency by 50 μg of Ag@Ag2O NCs against Candida albican; implying promising activity against COVID-19 white fungal post-infections. Through assessing cytotoxicity, Ag@Ag2O NCs exhibited higher safety against Vero cells than bulk silver nitrate by more than 100-fold.

No abstract

Thermoelectric generators made by large arrays of nanowires perpendicular to a silicon substrate, that is, so-called silicon nanowire forests are fabricated on large areas by an inexpensive metal-assisted etching technique. After fabrication, a thermal diffusion process is used for doping the nanowire forest with phosphorous. A suitable experimental technique has been developed for the measurement of the Seebeck coefficient under static conditions, and results are reported for different doping parameters. These results are in good agreement with numerical simulations of the doping process applied to silicon nanowires. These devices, based on doped nanowire forests, offer a possible route for the exploitation of the high power factor of silicon, which, combined with the very low thermal conductivity of nanostructures, will yield a high efficiency of the conversion of thermal to electrical energy.

Improper lignocellulosic waste disposal causes severe environmental pollution and health damage. Corn Stover (CS), agricultural, and aseptic packaging, Tetra Pak (TP) cartons, agro-industrial, are two examples of sustainable wastes that are rich in carbohydrate materials and may be used to produce valuable by-products. In addition, attempts were made to enhance cellulose fractionation and improve enzymatic saccharification. In this regard, these two wastes were efficiently employed as substrates for bioethanol production. This research demonstrates the effect of disodium hydrogen phosphate (Na2HPO4) and zinc chloride (ZnCl2) (NZ) as a new catalyst on the development of the sequential pretreatment strategy in the noticeable enzymatic hydrolysis. Physico-chemical changes of the native and the pretreated sustainable wastes were evaluated by compositional analysis, scanning electron microscopy (SEM), X-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). These investigations showed major structural changes after the optimized sequential pretreatment. This pretreatment not only influences the delignification process, but also affects the functionalization of cellulose chemical structure. NZ released a higher glucose concentration (328.8 and 996.8 mg/dl) than that of ZnCl2 (Z), which released 203.8 and 846.8 mg/dl from CS and TP, respectively. This work led to the production of about 500 mg/dl of ethanol, which is promising and a competitor to other studies. These findings contribute to increasing the versatility in the reuse of agricultural and agro-industrial wastes to promote interaction areas of pollution prevention, industrialization, and clean energy production, to attain the keys of sustainable development goals.