A mechanical model for the lateral compression of woven fabrics is derived from Van Wyk's compression law for fiber assemblies. The pressure ( P ) and thickness (v) relationship is P = a/ ( v -v')3. The parameter v' refers to the core of the fabric, which is incompressible over the pressure range 2-5000 gf/cm 2 . The parameter a refers to the compressible surface layers and is dependent on the mass of fibers in the surface layers and their orientation.A comparison is made of the results obtained with the KES-F fabric compression tester and the standard fabric thickness tester. The energy of compression is proportional to the cube root of the parameter a. The compressibility of the fabric is proportional to the energy of compression per unit volume of fabric. The changes that occur in the fabric surface layers during a typical fabric finishing process are investigated.The measurement of the lateral or thickness compression properties of fabrics forms an integral part of objective measurements currently being considered internationally for wool fabrics [ 12,17]. These objective measurements are intended to help maintain consistent quality in finished wool fabrics and to aid in product engineering of wool fabrics. An early paper [2] described the thickness-compression curve of fabrics. The effects of finishing treatments on the lateral compression curves of fabrics have been described [3,9,13], but the thickness-compression curves of fabrics have not been analyzed mechanically. An analysis of the mechanics of fabric compression may help in developing compression test methods and interpreting results. In this paper, we present a mechanical model that describes the compression curves measured on a large number of woven fabrics over the pressure range of 2-5000 gf/cm2. The model reduces the fabric to three layers -a relatively incompressible core layer in contact with a much more compressible surface layer on either side. The model is reconciled with both electron microscope evidence and optical measurements made on the fabrics.The model indicates that the DIN standard [6] for measuring fabric compression is very simply related to the compression test performed on the Kawabata evaluation system for fabrics . The change in the compression properties of wool fabrics in some commercial worsted fabric finishing processes is presented and interpreted in terms of the model.
Recently developed by CSIRO for quality control and assurance of fabrics, FAST, or fabric assurance by simple testing, consists of a series of instruments that are in expensive, robust, and simple to use, and their related test methods. FAST is specifically designed for use by tailors and worsted finishers; it measures fabric properties that are closely related to the ease of garment making-up and the durability of worsted finishing. FAST- I gives a direct reading of fabric thickness over a range of loads with micrometer resolution. FAST-2 measures the fabric bending length and its bending rigidity. FAST- 3 measures fabric extensibility at low loads. Fabric shear rigidity is calculated from the 45° bias extensibility. FAST-4 is a quick test for measuring fabric dimensional stability, including both relaxation shrinkage and hygral expansion.
Data on the linear viscoelastic relaxation of wool fibers for a range of relative hu midities below the gas transition ( Tg) are systematized by a humidity-time superposition method. The differences in the relaxation behavior in water where the fiber is above its Tg are pointed out. The analysis relates to the properties of the water sensitive, viscoelastic component of the wool fiber and consists of superimposing the relaxation curves for different humidities onto the curve for the dry state by multiplicative scaling and shifting on the logarithmic scale of the reduced time variable λ, that corrects for the influence of ageing. The change of the scaling and shift factor with the absorption mechanism of the water is discussed.
We evaluated the usefulness of saponification, direct solvent extraction, and Soxhlet extraction as extraction methods to determine the amounts of tocopherols in soybeans. Soxhlet extraction yielded the highest analytical values for each tocopherol homolog and was the best method for quantifying tocopherols in soybeans. Coupling of simple Soxhlet extraction with HPLC provided a highly reproducible procedure to quantify tocopherols in soybeans. The percent mean recovery 6 standard deviation (n = 5) was 103.2 6 1.21, 109.8 6 4.18, 93.8 6 1.12, and 106.9 6 1.54% for a-, b-, g-, and d-tocopherol, respectively. The linearity test for quantification was carried out over the ranges of 0.4-10.0, 0.2-4.0, 2.0-16.0, and 0.4-10.0 mg/mL for a-, b-, g-, and dtocopherol, respectively. Regression analysis showed an excellent linear relationship (R 2 .0.998), and the results of the validation parameters were generally reliable and satisfactory.
A general energy analysis has been formulated and applied to the study of fabric mechanics with the aid of computer programs. The analysis is chiefly concerned with the elastic or recoverable mechanisms of fabric rheology. The computer programs can be readily adapted to provide a solution for various fabric structures and deformations simply changing the boundary conditions.The energy analysis is based on the fundamental principle that elastic structures alway s assume a confguration of minimum strain energy, regardless of the deformation applied. The resulting minimization problem is solved with the use of a specific optimization technique -i.e., it is treated as an optimal control problem. In particular, the total yarn strain encrgy (consisting of the sum of the individual yarn bending. torsion, lateral compression, and longitudinal extension strain energies) is minimized, subject to certain constraints which give rise to internal forces and couples acting within the fabric structure itself. The constraints lead to the necessity of optimizing the "total" energy, or the sum of the potential energy due to the internal forces of constraint, and the yarn strain energy comprising the bending, torsion, and extension energies. < , at UQ Library on June 20, 2015 trj.sagepub.com Downloaded from
Quantitative trait loci (QTL) associated with six physical traits of cooked rice and seven chemical properties of rice grain were identified using a recombinant inbred (RI) population of rice evaluated over 3 years at the National Honam Agricultural Research Institute in Korea. The RI population consisted of 164 lines derived from a cross between Milyang23 and Gihobyeo, and the genetic map consisted of 414 molecular markers. A total of 49 QTL were identified for the 13 physico-chemical properties using composite interval mapping. Of these, 13 QTL were identified for 2 or more years, while 36 were detected in only 1 year. Five QTL were identified over all 3 years and will be useful for marker-assisted improvement of rice grain quality in Korea. The two QTL with the highest LOD scores, adhesiveness1.2 and potassium content7.1, provide a valuable starting point for positional cloning of genes underlying these QTL.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.