Vibration energy harvesting is receiving a considerable amount of interest as a means for powering wireless sensor nodes. This paper presents a small (component volume 0.1 cm 3 , practical volume 0.15 cm 3 ) electromagnetic generator utilizing discrete components and optimized for a low ambient vibration level based upon real application data. The generator uses four magnets arranged on an etched cantilever with a wound coil located within the moving magnetic field. Magnet size and coil properties were optimized, with the final device producing 46 µW in a resistive load of 4 k from just 0.59 m s −2 acceleration levels at its resonant frequency of 52 Hz. A voltage of 428 mVrms was obtained from the generator with a 2300 turn coil which has proved sufficient for subsequent rectification and voltage step-up circuitry. The generator delivers 30% of the power supplied from the environment to useful electrical power in the load. This generator compares very favourably with other demonstrated examples in the literature, both in terms of normalized power density and efficiency.

No abstract

Triboelectric nanogenerators (TENG) are one of the most promising candidates for powering wearable and portable devices. Example TENGs have demonstrated flexibility, light weight, biocompatibility, versatility and good performance. Textiles are a potential substrate onto, or into, which wearable technology is increasingly being incorporated but supplying power remains an enduring challenge. TENGs are a potential textile based mechanical energy harvesting power supply and there has been an increasing effort to combine TENGs with fabrics. A significant challenge exists in the integration without losing the performance of the TENG or the original properties (appearance, breathability, washability, and durability) and feel of the textile. Various approaches towards the realisation of textile-based TENGs (T-TENGs) have been demonstrated. Depending on its structure, T-TENGs can be divided into two main types, fabric-based TENG and fibre-based TENG. The fabric-based TENG is composed of conventional and/or modified fabrics, which serve as a substrate and/or a triboelectric material. The fibre-based TENG is fabricated as a single fibre or a collection of interlaced fibres. This paper provides an up to date review of the progress in the research of T-TENGs. The paper covers the basic operating principles, possible operation modes, textile manufacturing methods, material selections, T-TENG fabrication process, surface modification and structural designs. Issues, such as standardised measurement parameters, the challenges and limitations of T-TENG are discussed.

This paper reports the development and implementation of an energy aware autonomous wireless condition monitoring sensor system (ACMS) powered by ambient vibrations. An electromagnetic (EM) generator has been designed to harvest sufficient energy to power a radio-frequency (RF) linked accelerometer-based sensor system. The ACMS is energy aware and will adjust the measurement/transmit duty cycle according to the available energy; this is typically every 3 s at 0.6 m s rms acceleration at a frequency of 52 Hz. In addition, a voltage multiplier circuit is shown to increase the electrical damping compared to a purely resistive load; this allows for an average power of 120 μW to be generated at 1.7 m s −2 rms acceleration. The ACMS has been successfully demonstrated on an industrial air compressor and an office air conditioning unit, continuously monitoring vibration levels and thereby simulating a typical condition monitoring application.

Practical wearable e‐textiles must be durable and retain, as far as possible, the textile properties such as drape, feel, lightweight, breathability, and washability that make fabrics suitable for clothing. Early e‐textile garments were realized by inserting standard portable electronic devices into bespoke pockets and arranging interconnects and cabling across the garment. In these examples, the textile merely served as a vehicle to house the electronics and had no inherent electronic functionality. A reduction in electronic component size, the development of flexible circuits, and the ability to weave robust interconnects offer the potential for improved levels of electronic integration within the textile. The weaving of electronic circuit filaments less than 2 mm wide into fabrics such that the electronics are fully concealed in the textile and given extra protection by the surrounding textile fibers is introduced. The failure mechanisms for different filament circuit designs before and after integration into the textile are investigated with a 90° cyclical bending test. Results show that encapsulated filament circuits embedded within the textile survive 45 washing cycles and more than 1500 cycles of 90° bending around a bending radius of 10 mm, performing five times better than equivalent filament circuits before integration into the fabric.