Objective: To evaluate whether overloading of teeth can be avoided by utilizing aligners with reduced thicknesses of 0.4 mm or 0.3 mm. Materials and Methods: The experimental setup included an acrylic maxillary jaw model with tooth 11 separated and fixed via a 3-D force-moment transducer to a hexapod for experimental movement. Aligners tested were fabricated on duplicate stone models using commercially available polyethylene terephthalate glycol (PET-G) foils with thicknesses between 0.5 and 0.75 mm, and novel 0.4-mm-and 0.3-mm-thick foils. With the test aligner seated, 11 was bodily displaced in a labiopalatal direction in the range of 60.25 mm while all six force-and-moment components exerted on this tooth were registered. Results: With the thinnest commercially available 0.5-mm aligner, median forces of À7.89 N and 8.37 N were measured for the maximum 0.25-mm movement of 11 in a labial and palatal direction, respectively. In comparison, force values were 35% and 71% lower for the novel aligners with a thickness of 0.4 mm and 0.3 mm, respectively. Conclusions: Novel ''leveling'' aligners with reduced thickness may reduce overloading of individual teeth during aligner therapy. Due to form instability of 0.3-mm aligners, we suggest a novel sequence of 0.4-0.5-0.75 mm for aligner systems using several foil thicknesses for load graduation within single setup steps. This would combine low stiffness of the initial aligner and relatively constant load increases throughout the treatment. (Angle Orthod. 2016;86:883-890)

A significant load reduction can be achieved with the new thinner aligners. Because of the form instability of the 0.3-mm aligner during handling, we suggest the novel sequence 0.4, 0.5, and 0.75 mm for aligner systems based on sequentially increased material thickness. This sequence combines sufficiently low initial aligner stiffness and steady load increases in single setup steps. The viscoelastic behavior of polyethylene terephthalate glycol aligners observed during incisor derotation should lead to a reduction of the high initial load exerted directly after intraoral aligner insertion.

Since most real-time audio and video applications lack of QoS support, QoS demand of such IP data streams shall be detected and applied automatically. To support QoS in LANs, especially in home environments, a system was developed, which enables self-organised QoS for unmanaged networks through host implementations -in contrast to traditional solutions without network support. It supports per-link reservation and prioritisation and works without a need for application support. One part of this system is an automated traffic identification and classification system, which is subject of this paper. An efficient set of attribute meters, based on the Statistical Protocol IDentification (SPID), was investigated, enhanced and evaluated. We improved the performance, added support for UDP protocols and real-time identification. It is shown that using our implementation efficient near real-time protocol identification on per-flow basis is possible to support self-organised resource reservation.

In view of these differences in material properties, the clinical data from long-term use of the bone cements Refobacin Palacos R and Palacos R + G cannot be extrapolated to the newly developed PMMA cements Refobacin Bone Cement R and Smart GHV. Before broad clinical use of these cements, prospective clinical studies using RSA or DEXA and, as a second step, statistically powerful prospective comparative studies should be performed. Until these data are available, patients in whom Refobacin Bone Cement R and SmartSet GHV are used should be informed that the material employed deviates from the standard procedures for cemented joint replacement in the Scandinavian arthroplasty registers and that the long-term consequences cannot, in the final instance, be foreseen. This is essential in order to avoid later malpractice claims on the grounds of inadequate information.

Rat models are widely used in preclinical studies investigating fracture healing. The interfragmentary movement at a fracture site is critical to the course of healing and therefore demands definition in order to aptly interpret the experimental results. Estimation of this movement requires knowledge of the fixation stiffness and loading. The characteristic loading for the rat femur has been estimated, but the stiffness of fixation used in rat studies has yet to be fully described. This study aimed to determine the 6 degree of freedom stiffness of four commonly used implants, two external fixators (RatExFix and UlmExFix), a locking plate, and a locking intramedullary nail, in all degrees of freedom and estimate the interfragmentary movement under specific physiological loads. The external fixator systems allow the greatest movement. Mounted 45° anterolateral on the femur, the RatExFix allows an average of 0.88 mm of motion in each anatomic direction while the stiffer UlmExFix allows about 0.6 mm of motion. The nail is far stiffer than the other implants investigated while the plate allows movement of an intermediate magnitude. Both the nail and plate demonstrate higher axial than shear stiffness. The relatively large standard deviations in external fixator shear motion imply strong dependence on bone axis alignment across the gap and the precise orientation of the specimen relative to the loading. The smaller standard deviation associated with the nail and plate results from improved alignment and minimization of the influence of rotational positioning of the specimen due to the reduced implant eccentricity relative to the specimen axis. These results show that the interfragmentary movement is complex and varies significantly between fixation devices but establishes a baseline for the evaluation of the results of different studies.