Proses penetasan telur melibatkan teknologi kontrol untuk memantau kondisi suhu dan kelembaban udara pada kabin penetasan. Teknologi kontrol yang digunakan masih menerapkan kontrol on-off. Pada artikel ini dibahas perbandingan kinerja mesin penetas telur dengan menggunakan kontrol on-off dan kontrol PWM (Pulse Width Modulation). Kontrol PWM yang digunakan berbasis pada mikrokontroler arduino dan aktuator sebuah bola lampu pijar. Hasil yang didapatkan setelah dilakukan pengujian adalah kinerja mesin tetas telur dengan kontrol PWM lebih baik dibandingkan dengan menggunakan kontrol on-off. Respons peralihan dengan kontrol PWM lebih cepat yaitu 120 detik sedangkan dengan menggunakan kontrol on-off selama 240 detik. Penggunaan kontrol PWM juga lebih stabil daripada kontrol on-off dilihat dengan osilasi pada steady-state response sebesar 0,3 0 C, sedangkan pada kontrol on-off sekitar 4 0 C.
AbstrakSistem pendingin konvensional berdasarkan kompresi uap memiliki koefisien kinerja (COP) yang tinggi. Namun terdapat kekurangan sistem pendingin kompresi uap saat ini masih menggunakan refrigeran yang memiliki efek merugikan pada lingkungan. Untuk itu dilakukan penelitian mesin penyimpan buah dan sayuran dengan menggunakan sistem termoelektrik tipe TEC1-12706 dengan sistem kontrol suhu menggunakan arduino. Pada penelitian ini suhu di dalam kabin dapat stabil pada 15°C dan masih layak untuk digunakan sebagai penyimpan buah dan sayuran.
ABSTRAKJurnal ini menyajikan sebuah model empiris untuk mensimulasikan karakteristik sistem pendingin untuk jamur merang. Model matematika didasarkan pada hasil pengukuran suhu. Parameter, seperti, Gain (K), waktu tunda (θ), dan waktu konstan (τ) diperoleh dari nilai-nilai eksperimental. Sistem pendingin dirancang dengan menggunakan metode kurva reaksi proses, sedangkan pengontrol PID dengan metode korelasi Ciancone. Kontrol PID berhasil diterapkan, hal ini dapat dilihat dari tidak adanya kesalahan tunak, respon sistem yang lebih cepat mencapai set-point, overshoot dan undershoot tidak terlalu jauh dari nilai masukan. Kata Kunci : Sistem Pendingin; Jamur Merang; Kurva Reaksi Proses; Pengontrol PID; ABSTRACTThe present work proposes a empirical model to simulate the steady-state behavior of a refrigeration sistem for paddystraw mushroom (showcase). The current mathematical model is based on result of measurement temperature. Parameters, such as, Gain (K), delay time (θ), and time constant (τ) are obtained from experimental values.The sistem designed using the process reaction curve method, while the PID controller with correlation method Ciancone. PID control successfully implemented, it can be seen from the absence of steady-state error, a faster sistem response reach the set-point, overshoot and undershoot is not too far from the input value.Keywords : Refrigeration Sistem; Paddystraw Mushroom; Process Reaction Curve; PID Controller; PENDAHULUAN Jamur merang merupakan produk pertanian yang mudah rusak dan tidak dapat disimpan dalam jangka waktu yang lama pada kondisi suhu kamar normal. Bahkan, menurut Etty Sumiati dan Diny Djuariah, Jamur merang mempunyai umur simpan kurang dari satu hari atau maksimum satu hari. Menurut Tao (1), Untuk memperpanjang umur simpan jamur dapat dilakukan dengan 3 cara pengkondisian, yaitu disimpan pada ruang dingin dengan suhu 4±1 o C dengan RH 75%. Maka diperlukan control terhadap suhu dan kelembaban udara pada ruang penyimpan jamur merang tersebut. Dewasa ini sistem control yang diterapkan pada sistem refrigerasi masih menggunakan sistem control posisi ON-OFF. Untuk mendapatkan tanggapan sistem yamg lebih presisi diperlukan kendali PID.Pada aplikasi industri sistem-sistem saling berhubungan satu dengan yang lainnya.Seperti yang terdapat pada: petro-kimia, pembuatan kertas dan instalasi pengolahan air. Banyak dari aplikasi ini menyebabkan proses pengendalian mengalami
This paper offers an alternative method of making PCB routing using a negative dry film photoresist and a maskless photolithography method. The objective of this research is to determine the correct parameters for the process of making PCB design easier, cheaper and safer. Electronic circuit design was created on a laptop or PC using Autodesk EAGLE software with a combination of result is black and blue light color. PCB routing design was inserted into a PowerPoint slide to display on a commercial Digital Light Processing (DLP) projector. No modifications were made to a projector, which was mounted directly on a stand with a downward facing position. The projector lamp replaced an ultraviolet or X-ray source during the exposure process, exposing PCB coated in negative dry film photoresist. After the exposure process, the PCB was inserted into the developer solution, causing the blue light irradiated part to remain while the blackened sections dissolved. The PCB was then added to an etching solution to scrape the copper unprotected by the photoresist. The PCB was finally soaked in a remover solution to remove the photoresist. Once complete, the process generated a laptop-designed PCB routing. Electrical lines can be created using this method with a size of 100 µm and a lane edge deviation of 5 µm. The goal of research to make PCB routing cheaper, easier and safer was achieved. Evidenced by the installation of electronic components and then tested, the results are all components function well.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.