Penelitian ini bertujuan untuk mengevaluasi pengaruh penggunaan media udara sebagai pendingin pada modul fotovoltaik terhadap daya keluaran dan efisiensi listrik. Energi fosil, sebagai sumber energi utama saat ini, memiliki keterbatasan persediaan dan menghadirkan tantangan dalam pemenuhan kebutuhan energi di masa depan. Dalam upaya untuk mengatasi masalah ini, kami melakukan pengujian dengan menambahkan sistem pendinginan udara menggunakan blower di bagian bawah modul fotovoltaik. Pengujian dilakukan dengan variasi laju aliran udara, dan hasilnya menunjukkan bahwa penggunaan media pendinginan udara dapat meningkatkan daya keluaran dan efisiensi modul fotovoltaik. Rata-rata daya keluaran meningkat sebesar 31,66 Watt dengan efisiensi sebesar 3,52%. Namun, ketika laju aliran udara meningkat sebesar 1,5 m/s, terjadi penurunan daya ratarata sebesar 28,9 Watt dan efisiensi sebesar 3,22%. Hasil ini menunjukkan bahwa kecepatan udara mempengaruhi temperatur, daya keluaran, dan efisiensi modul fotovoltaik.
Until 2012, the electrification ratio in Gorontalo Province was 64.35%. The potential of primary energy available in Gorontalo to generate electrical energy is quite large and has opportunities to be developed, be it hydro, solar, or geothermal. The use of sunlight as a source of electrical energy is carried out using solar cells or solar panels. Solar panels can be used to convert solar radiation into electrical energy. The electric voltage generated by the solar panels can be used to charge the battery. Besides, the potential for thermal energy from hot springs can also be used as electrical energy by using a Thermoelectric Generator (TEG). The purpose of this study is to test whether the use of thermoelectric placed on aluminum plates can increase the voltage output of the thermoelectric generator and compare the resulting output voltage between hybrid energy, (solar cell and thermoelectric generator). The method used in this study is to measure the output voltage generated by the solar panels and each TEG every 1 hour. Then measure the total voltage of the hybrid generator. The results showed that the voltage obtained from TEG utilization depends on the temperature received by the TEG. The highest voltage is at TEG 6 at 3.7V at 10.00. the highest hybrid voltage is 37.4 v. Sampai dengan tahun 2012 rasio elektrifikasi di Provinsi Gorontalo sebesar 64,35%[1]. Potensi energi primer yang tersedia di Gorontalo untuk membangkitkan energi listrik cukup besar dan mempunyai peluang untuk dikembangkan baik itu tenaga air, matahari maupun tenaga panas bumi. Pemanfaatan cahaya matahari sebagai sumber energi listrik dilakukan dengan menggunakan solar sel atau panel surya. Panel surya dapat dimanfaatkan untuk mengkonversi radiasi matahari menjadi energi listrik. Tegangan listrik yang dihasilkan oleh panel surya dapat dipakai untuk mengisi baterai. Selain itu juga Potensi energi panas dari sumber air panas juga dapat dimanfaatkan menjadi energi listrik dengan menggunakan Thermoelectric Generator (TEG). Tujuan dari penelitian ini yaitu menguji apakah penggunaan Termoelektrik yang diletakkan pada pelat almunium dapat meningkatkan output tegangan dari thermoelektrik generator dan membandingkan tegangan output yang dihasilkan antara hybrid energy, (solar cell dan thermoelektrik generator). Metode yang dilakukan pada penelitian ini yaitu mengukur tegangan output yang dihasilkan oleh panel surya dan masing-masing TEG tiap 1 jam. Kemudian mengukur tegangan total pembangkit hybrid. Hasil penelitian menunjukan bahwa tegangan yang di dapatkan dari pemanfaatan TEG tergantung dari suhu yang di terima oleh TEG tersebut. tegangan paling tinggi berada pada TEG 6 sebesar 3.7V pada pukul 10.00. tegangan hybrid paling tinggi yaitu 37.4 v.
The purpose of implementing this Community Service program is to provide knowledge and skills insights for graduates about entrepreengineering, which can be used to demonstrate soft skills in the workplace or as a support in planning a project. This activity is carried out by providing training, including lectures, discussions, and simulations on the preparation of the Budget Plan (RAB) and Detail Engineering Drawing (DED). These targets and partners are alumni and users of work graduates such as consulting companies and contractors. The implementation of community service activities has been running according to the agreed plan. In the implementation process, this activity is carried out on an ongoing basis to implement the PKM program. This program has a lasting impact on preparing graduates who are excellent and ready to work
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.