No abstract

Additive manufacturing is a promising tool that has proved its value in various applications. Among its technologies, the fused filament fabrication 3D printing technique stands out with its potential to serve a wide variety of applications, ranging from simple educational purposes to industrial and medical applications. However, as many materials and composites can be utilized for this technique, the processability of these materials can be a limiting factor for producing products with the required quality and properties. Over the past few years, many researchers have attempted to better understand the melt extrusion process during 3D printing. Moreover, other research groups have focused on optimizing the process by adjusting the process parameters. These attempts were conducted using different methods, including proposing analytical models, establishing numerical models, or experimental techniques. This review highlights the most relevant work from recent years on fused filament fabrication 3D printing and discusses the future perspectives of this 3D printing technology.

The optimum tilt angle of solar panels or collectors is crucial when determining parameters that affect the performance of those panels. A mathematical model is used for determining the optimum tilt angle and for calculating the solar radiation on a south-facing surface on a daily, monthly, seasonal, semi-annual, and annual basis. Photovoltaic Geographical Information System (PVGIS) and Photovoltaic Software (PVWatts) is developed by the NREL (US National Renewable Energy Laboratory) are also used to calculate the optimum monthly, seasonal, semi-annual, and annual tilt angles and to compare these results with the results obtained from the mathematical model. The results are very similar. PVGIS and PVWatts are used to estimate the solar radiation on south-facing surfaces with different tilt angles. A case study of a mono-crystalline module with 5 kWP of peak power is used to find out the amount of increased energy (gains) obtained by adjusting the Photovoltaic (PV) tilt angles based on yearly, semi-annual, seasonal, and monthly tilt angles. The results show that monthly adjustments of the solar panels in the main Palestinian cities can generate about 17% more solar energy than the case of solar panels fixed on a horizontal surface. Seasonal and semi-annual adjustments can generate about 15% more energy (i.e., it is worth changing the solar panels 12 times a year (monthly) or at least 2 times a year (semi-annually). The yearly optimum tilt angle for most Palestinian cities is about 29°, which yields an increase of about 10% energy gain compared to a solar panel fixed on a horizontal surface.

With the growing demand for clean and economically feasible renewable energy, solar photovoltaic (PV) system usage has increased. Among many factors, the tilt and azimuth angles are of great importance and influence in determining the photovoltaic panel’s efficiency to generate electricity. Although much research was conducted related to solar PV panels’ performance, this work critically determined the tilt and azimuth angles for PV panels in all countries worldwide. The optimum tilt and azimuth angles are estimated worldwide by the photovoltaic geographic information system (PVGIS). Also, annual and average daily solar irradiation incident on the tilted and oriented plate optimally (AR1 and DR1) are calculated. Besides, annual and average daily solar irradiation incident on plate tilt optimally and oriented because of the south in the northern hemisphere and because of the north in the southern hemisphere (AR2 and DR2) are estimated. PVGIS is also used to calculate the annual and average daily solar irradiation incident on the horizontal plate (AR3 and DR3). The data collected from PVGIS are used to develop an efficient and accurate artificial neural network model based on feed-forward neural network approach. This model is an essential subpart that can be used in an embedded system or an online system for further PV system analysis and optimization. The developed neural model reflected very high accuracy in predicting the PV panels’ optimal tilt and azimuth angles worldwide. The benefit of tilting is generally increased by increasing the latitude. As the latitude increases, the tilt factor (F) increases because of the increase in the optimum tilt angle by increasing the latitude. The optimal orientation is due to the north in the southern hemisphere and due to the south in the northern hemisphere for most cities worldwide. In sum, it can be concluded that the optimum tilt angle is equal to or greater than the latitude until the latitude 30°. The optimum tilt angle becomes less than the latitude, and the difference is increased until it reaches more than 20°. Hence in this study the aim is to develop a simple neural network model which can accurately predict the annual radiation and optimum tilt and azimuth angle in any region of the world and can be easily implemented in a low-cost microcontroller.

The rising usage of carbon and glass fibers has raised awareness of scrap management options. Every year, tons of composite scrap containing precious carbon and glass fibers accumulate from numerous sectors. It is necessary to recycle them efficiently, without harming the environment. Pyrolysis seems to be a realistic and promising approach, not only for efficient recovery, but also for high-quality fiber production. In this paper, the essential characteristics of the pyrolysis process, their influence on fiber characteristics, and the use of recovered fibers in the creation of a new composite are highlighted. Pyrolysis, like any other recycling process, has several drawbacks, the most problematic of which is the probability of char development on the resultant fiber surface. Due to the char, the mechanical characteristics of the recovered fibers may decrease substantially. Chemically treating and post-heating the fibers both help to reduce char formation, but only to a limited degree. Thus, it was important to identify the material cost reductions that may be achieved using recovered carbon fibers as structural reinforcement, as well as the manufacture of high-value products using recycled carbon fibers on a large scale. Recycled fibers are cheaper than virgin fibers, but they inherently vary from them as well. This has hampered the entry of recycled fiber into the virgin fiber industry. Based on cost and performance, the task of the current study was to modify the material in such a way that virgin fiber was replaced with recycled fiber. In order to successfully modify the recycling process, a regulated optimum temperature and residence duration in post-pyrolysis were advantageous.