Inspeksi label produk menjadi bagian penting dalam pengawasan fabrikasi dan kendali kualitas hasil produksi di industri. Beberapa industri masih menerapkan pemeriksaan label produk secara visual-manual oleh operator. Cara ini memiliki keterbatasan dan cenderung tidak cukup efektif. Penelitian ini mengembangkan sistem inspeksi kualitas pelabelan produk secara otomatis menggunakan penggabungan metode golden template comparison berdasarkan analisis pixel matching dan konveyor pemilah. Perangkat konveyor pemilah mampu memindahkan produk ke proses deteksi dua sisi label dan memilah produk secara otomatis berdasarkan hasil inspeksi produk. Penggunaan golden template comparison ini efektif membandingkan intensitas pixel dari objek yang diperiksa dengan golden template yang sudah ditentukan. Hasil penelitian menunjukkan sistem ini berhasil menganalisa produk yang pass dan fail berdasarkan perhitungan total defect area kedua sisi front dan back pada label produk sesuai standar acuan klasifikasi cacat yang ditentukan.
COVID-19 menyerang manusia pada akhir tahun 2019. Penyebaran COVID-19 terjadi melalui droplet/cairan yang keluar dari mulut/hidung manusia. Antisipasi penyebaran COVID-19 dilakukan dengan menerapkan pola hidup bersih dan sehat. Salah satu caranya adalah dengan mencuci tangan menggunakan hand sanitizer. Penggunaan hand sanitizer di tempat umum memungkinkan terjadinya kontak fisik antar pengguna sehingga diperlukan cara untuk mengurangi kontak fisik tersebut. Cara yang bisa diterapkan adalah dengan menggunakan hand sanitizer otomatis. Prinsip dari hand sanitizer otomatis ini adalah ketika tangan didekatkan dengan botol hand sanitizer maka secara otomatis cairan akan keluar dengan sendirinya ke telapak tangan. Berdasarkan hasil penelitian yang telah dilakukan, hand sanitizer telah berhasil dibuat dan dapat digunakan di Politeknik Negeri Batam.
Long Rang Access (LoRa) merupakan bagian dari teknologi Low Power Wide Area Network (LPWAN) yang banyak digunakan karena memiliki karakteristik berdaya rendah dan dapat menjangkau area yang jauh secara nirkabel. Pada penelitian ini telah dilakukan penerapan komunikasi nirkael LoRa pada sistem pencatat kehadiran portabel yang dapat digunakan dosen dan dan karyawan serta mahasiswa dalam merekam presensi saat beraktifitas di luar ruangan. Setelah dilakukan instalasi dan konfigurasi, dilakukan pongujian baik di dalam maupun di luar area kampus Politeknik Negeri Batam. Terdapat sembilan titik lokasi pengujian di dalam area kampus dan delapan titik lokasi pengujian di luar area kampus. Dengan menggunakan LoRa yang bekerja pada frekuensi 915 MHz, set SF=7 dan BW=125 KHz, didapatkan jangkauan terjauh hingga 456,01 meter. Keberhasilan penerimaan data dipengaruhi oleh jarak; banyak rintangan seperti beton, kaca, pepohonan dan gedung-gedung tinggi disekitar titi pengujian; frekuensi; dan bentuk antenna. Secara umum, komunikasi nirkabel LoRa dapat diterapkan pada sistem pencatat kehadiran portabel, namum masih terdapat ruang untuk pengembangan kedepannya terutama pada optimalisasi area jangkauan.
Modul akuisisi data dengan menggunakan Modbus Remote Terminal Unit (RTU) telah banyak digunakan secara komersial di industri. Namun sayangnya, harga peralatan tersebut tergolong mahal. Protokol komunikasi Modbus RTU ini cukup kompleks untuk dibuat oleh pengguna awam, seperti siswa sekolah menengah vokasi dan mahasiswa. Dengan latar belakang tersebut, penelitian ini bertujuan untuk membuat modul komunikasi Modbus RTU over RS485 yang berbasiskan Arduino sehingga harga pembuatannya menjadi murah dan dapat menjadi sarana pembelajaran di sekolah menengah maupun universitas. Modul yang dibuat ini terdiri atas dua input analog dan dua input/output digital. Sinyal analog yang masuk dikondisikan terlebih dahulu dengan menggunakan signal conditioner sebelum diproses lebih lanjut oleh mikrokontroler. Hasil pengujian menggunakan Modbus Analyzer menunjukkan bahwa komunikasi Modbus RTU over RS485 pada modul yang telah dibuat ini berjalan dengan baik.
Gerak jatuh bebas merupakan salah satu topik pembelajaran pada mata kuliah Fisika. Salah satu cara agar mahasiswa memahami materi yang disampaikan adalah dengan cara melakukan praktikum. Modul praktikum pemodelan gerak jatuh bebas ini dibuat dengan dengan menggunakan tujuh infrared obstacle avoidance sensor dan Arduino. Masing-masing sensor diletakkan pada ketinggian 0,82 m; 0,695 m; 0.62 m; 0,392 m; 0,295 m; dan 0,2 m. Benda dijatuhkan dan dideteksi oleh ketujuh sensor tersebut. Setelah semua sensor mendeteksi benda yang dijatuhkan, maka waktu untuk masing-masing sensor ditampilkan pada serial monitor Arduino. Data waktu tersebut dipindahkan ke ms. Excel dan dibuat grafik hubungan antara ketinggian terhadap waktu. Dari 10 kali percobaan didapatkan bahwa percepatan yang dialami oleh benda yang dijatuhkan adalah 9.8 m/s2.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.