Nanotechnology has been identified as having great potential for improving the efficiency of water prevention and purification while reducing costs. In this field, two applications of nanocellulose have generated attention and have proven to be a sound strategy as an adsorbent and as a membrane for the removal of contaminants. This potential is attributed to its high aspect ratio, high specific surface area, high capacity retention, and environmental inertness. In addition to the aforementioned advantages, the presence of active sites allows the incorporation of chemical moieties that may enhance the binding efficiency of pollutants to the surface. This review paper intends to understand how nanocellulose affects the adsorption behavior of water pollutants, e.g., heavy metal ions, microbes, dyes, and organic molecules, and is divided in two parts. First, a general overview of the different strategies for the preparation of nanocellulose is described, and its specific properties are reported. The second section reports some of its application as adsorbent nanomaterial or separation membrane. It appears that the use of nanocellulose for these applications is very promising for wastewater treatment industries.

The three-dimensional (3D) printed scaffolds were prepared by partial cross-linking of TEMPO-oxidized cellulose nanofibril/alginate hydrogel using calcium ions for printing the hydrogel while maintaining its shape, fidelity, and preventing the collapse of the filaments. The prepared scaffolds were fully cross-linked using calcium ions immediately after printing to provide the rigidity of the hydrogel and give it long-term stability. The composition of the prepared pastes was adjusted in view of the description of the hydrogel and 3D printing parameters. The rheological properties in terms of thixotropic behavior and viscosity recovery of hydrogels were investigated by performing steady shear rate experiments. The results show that the viscosity recovery for pure alginate hydrogel was only about 16% of the initial value, whereas it was 66% when adding cellulose nanofibrils to alginate. Consequently, the shape of the pure alginate scaffold was soft and easy to collapse contrarily to the composite scaffold. The biomimetic mineralization process of printed scaffolds using simulated body fluid, mimicking the inorganic composition of human blood plasma, was performed and the hydroxyapatite nucleation on the hydrogel was confirmed. The strength properties of the fabricated scaffolds in terms of compressive strength analysis were also investigated and discussed. The results show that the alginate/TEMPO-oxidized cellulose nanofibril system may be a promising 3D printing scaffold for bone tissue engineering.

No abstract

No abstract

Biomass pyrolysis is a promising renewable sustainable source of fuels and petrochemical substitutes. It may help in compensating the progressive consumption of fossil-fuel reserves. The present article outlines biomass pyrolysis. Various types of biomass used for pyrolysis are encompassed, e.g., wood, agricultural residues, sewage. Categories of pyrolysis are outlined, e.g., flash, fast, and slow. Emphasis is laid on current and future trends in biomass pyrolysis, e.g., microwave pyrolysis, solar pyrolysis, plasma pyrolysis, hydrogen production via biomass pyrolysis, co-pyrolysis of biomass with synthetic polymers and sewage, selective preparation of high-valued chemicals, pyrolysis of exotic biomass (coffee grounds and cotton shells), comparison between algal and terrestrial biomass pyrolysis. Specific future prospects are investigated, e.g., preparation of supercapacitor biochar materials by one-pot one-step pyrolysis of biomass with other ingredients, and fabricating metallic catalysts embedded on biochar for removal of environmental contaminants. The authors predict that combining solar pyrolysis with hydrogen production would be the ecofriendliest and most energetically feasible process in the future. Since hydrogen is an ideal clean fuel, this process may share in limiting climate changes due to CO 2 emissions.

No abstract

Cellulosic nanomaterials are potential candidates in different areas, especially in water treatment. In the current work, palm fruit stalks cellulose nanofibers (CNF), TEMPO-oxidized CNF (OCNF), and activated carbon (AC) were used to make thin film membranes for removal of E. coli bacteria from water. Two types of layered membranes were produced: a single layer setup of crosslinked CNF and a two-layer setup of AC/OCNF (bottom) and crosslinked CNF (up) on hardened filter paper. The prepared membranes were evaluated regarding their microstructure and layers thickness using scanning electron microscopy (SEM). Water flux and rejection of E. coli bacteria was tested using dead end stirred cells at 1 MPa pressure. Thickness of the cosslinked CNF layer in both types of membranes was about 0.75 micron. The results showed that exchanging water by isopropyl alcohol before drying increased porosity of membranes, and thus resulted in increasing pure water flux and flux of bacteria suspension. The two-layer AC/OCNF/CNF membrane had much higher water flux than the single layer CNF due to higher porosity seen on the surface of the former. Both types of membranes showed high capability of removing E. coli bacteria (rejection~96-99%) with slightly higher efficiency for the AC/OCNF/CNF membrane than CNF membrane. AC/OCNF/CNF membrane also showed resistance against growth of E. coli and S. aureus bacteria on the upper CNF surface while the single layer CNF membrane did not show resistance against growth of the aforementioned bacteria.

No abstract