Electrical actuators were made from films of dielectric elastomers (such as silicones) coated on both sides with compliant electrode material. When voltage was applied, the resulting electrostatic forces compressed the film in thickness and expanded it in area, producing strains up to 30 to 40%. It is now shown that prestraining the film further improves the performance of these devices. Actuated strains up to 117% were demonstrated with silicone elastomers, and up to 215% with acrylic elastomers using biaxially and uniaxially prestrained films. The strain, pressure, and response time of silicone exceeded those of natural muscle; specific energy densities greatly exceeded those of other field-actuated materials. Because the actuation mechanism is faster than in other high-strain electroactive polymers, this technology may be suitable for diverse applications.

A device configuration for light emission from electroactive polymers is described. In these light-emitting electrochemical cells, a p-n junction diode is created in situ through simultaneous p-type and n-type electrochemical doping on opposite sides of a thin film of conjugated polymer that contains added electrolyte to provide the necessary counterions for doping. Light-emitting devices based on conjugated polymers have been fabricated that operate by the proposed electrochemical oxidation-reduction mechanism. Blue, green, and orange emission have been obtained with turn-on voltages close to the band gap of the emissive material.

A number of materials have been explored for their use as artificial muscles. Among these, dielectric elastomers (DEs) appear to provide the best combination of properties for true muscle-like actuation. DEs behave as compliant capacitors, expanding in area and shrinking in thickness when a voltage is applied. Materials combining very high energy densities, strains, and efficiencies have been known for some time. To date, however, the widespread adoption of DEs has been hindered by premature breakdown and the requirement for high voltages and bulky support frames. Recent advances seem poised to remove these restrictions and allow for the production of highly reliable, high-performance transducers for artificial muscle applications.

No abstract

Transparent conductive electrodes with high surface conductivity, high transmittance in the visible wavelength range, and mechanical compliance are one of the major challenges in the fabrication of stretchable optoelectronic devices. We report the preparation of a transparent conductive electrode (TCE) based on a silver nanowire (AgNW) percolation network modified with graphene oxide (GO). The monatomic thickness, mechanical flexibility, and strong bonding with AgNWs enable the GO sheets to wrap around and solder the AgNW junctions and thus dramatically reduce the inter-nanowire contact resistance without heat treatment or high force pressing. The GO-soldered AgNW network has a figure-of-merit sheet resistance of 14 ohm/sq with 88% transmittance at 550 nm. Its storage stability is improved compared to a conventional high-temperature annealed AgNW network. The GO-soldered AgNW network on polyethylene terephthalate films was processed from solutions using a drawdown machine at room temperature. When bent to 4 mm radius, its sheet resistance was increased by only 2-3% after 12,000 bending cycles. GO solder can also improve the stretchability of the AgNW network. Composite TCE fabricated by inlaying a GO-soldered AgNW network in the surface layer of polyurethane acrylate films is stretchable, by greater than 100% linear strain without losing electrical conductivity. Fully stretchable white polymer light-emitting diodes (PLEDs) were fabricated for the first time, employing the stretchable TCE as both the anode and cathode. The PLED can survive after 100 stretching cycles between 0 and 40% strain and can be stretched up to 130% linear strain at room temperature.

No abstract

No abstract

Solid-state polymer light-emitting electrochemical cells have been fabricated using thin films of blends of poly(1,4-phenylenevinylene) and poly(ethylene oxide) complexed with lithium trifluoromethanesulfonate. The cells contain three layers:  the polymer film (as the emissive layer) and indium-tin oxide and aluminum films as the two contact electrodes. When externally biased, the conjugated polymers are p-doped and n-doped on opposite sides of the polymer layer, and a light-emitting p-n junction is formed in between. The admixed polymer electrolyte provides the counterions and the ionic conductivity necessary for doping. The p-n junction is dynamic and reversible, with an internal built-in potential close to the band gap of the redox-active conjugated polymer (2.4 eV for PPV). Green light emitted from the p-n junction was observed with a turn-on voltage of about 2.4 V. The devices reached 8 cd/m(2) at 3 V and 100 cd/m(2) at 4 V, with an external quantum efficiency of 0.3-0.4% photons/electron. The response speed of these cells was around 1 s, depending on the diffusion of ions. Once the light-emitting junction had been formed, the subsequent operation had fast response (microsecond scale or faster) and was no longer diffusion-controlled.