The article presents the potential impact of flat drive and transport belts on people’s safety during a fire. The analysis distinguished belts made of classically used fabric–rubber composite materials reinforced with cord and currently used multilayer polymer composites. Moreover, the products’ multilayers during the thermal decomposition and combustion can be a source of emissions for unpredictable and toxic substances with different concentrations and compositions. In the evaluation of the compared belts, a testing methodology was used to determine the toxicometric indicators (WLC50SM) on the basis of which it was possible to determine the toxicity of thermal decomposition and combustion products in agreement with the standards in force in several countries of the EU and Russia. The analysis was carried out on the basis of the registration of emissions of chemical compounds during the thermal decomposition and combustion of polymer materials at three different temperatures. Moreover, the degradation kinetics of the polymeric belts by using the thermogravimetric (TGA) technique was evaluated. Test results have shown that products of thermal decomposition resulting from the neoprene (NE22), leder leder (LL2), thermoplastic connection (TC), and extra high top cower (XH) belts can be characterized as moderately toxic or toxic. Their toxicity significantly increases with the increasing temperature of thermal decomposition or combustion, especially above 450 °C. The results showed that the belts made of several layers of polyamide can be considered the least toxic in fire conditions. The TGA results showed that NBR/PA/PA/NBR belt made with two layers of polyamide and the acrylonitrile–butadiene rubber has the highest thermal stability in comparison to other belts.
Since there are no legally defined testing requirements for mobile positive pressure fans, they may be tested based on methods that do not correspond to their actual operating conditions. Adequate assessment of the technical and operating conditions for this type of equipment is particularly important for equipment used in rescue operations. Such units should be characterized by efficient and reliable operation. This article investigates the influence of measurement methods of the volumetric airflow rate on the performance of a power unit. The article shows that the applied measurement method, whether it is PN-EN ISO 5801 (test conditions in a pipe duct—Method A) or other methods, i.e., ANSI/AMCA 240-15 and testing of the characteristics of the velocity profile (tests in open flow—Method B), can cause differences in the power demand of fans of from 3.2% to 4.5%. The differences in the requirements of propulsion power translate into fuel consumption and emissions of harmful exhaust gases generated by the combustion drive units (4 kW). It was also observed that fans with conventional impellers (W1) show a lower power demand when applying Method B (open flow) tests, while fans with turbo impellers (W2) show a lower power demand when Method A (duct) tests are applied. Comparative analysis of the parameters of the drive unit in the test group of fans without taking into account the measurement method can cause errors of up to about 7.7%, 6.4%, and 2.4% for the power, torque, and speed, respectively.
Aim: The aim of the article is to indicate the possible scope of application of mobile fans during the execution of rescue actions and identification of the parameters conditioning the effectiveness of using this type of units. Method Design: Mobile overpressure fans are a tool used during rescue operations mainly to remove hot gases and smoke, which accumulate in confined spaces covered by fire – primarily within the evacuation routes, but also in the rooms. In literature there are examples of other uses of the considered fans, e.g. to support the liquidation of fire hazards of free-standing objects (i.e. fires of cars or containers) and the rescue of trapped people in inaccessible spaces by supplying fresh air. This paper, which is based on literature review, is devoted to providing an approximation of the above applications. The effective use of mobile fans requires specialized theoretical and practical preparation. Therefore, the study also identified factors that may determine the successful implementation of the adopted tactical intent, which include in particular: the selection of appropriate openings (outlet and inlet), the selection of the gas exchange path and the proper positioning of a mobile fan. Conclusions: Literature analysis of the problem presented in this paper will be a fundamental point of reference for the research work carried out in subsequent stages related to the evaluation of the efficiency of mobile fans. As part of this work, large-scale tests will be carried out using appropriately designed and constructed test benches to evaluate the effectiveness of mobile units in real conditions. The knowledge gained in this way is intended to serve as material for further considerations on the creation of concepts of both subsequent methodologies and test stands required for their implemen- tation, enabling the verification of parameters characterizing the efficiency and reliability of mobile fans. Keywords: mobile positive pressure fans, tactical mechanical ventilation, rescue operations Type of article: review article
This paper presents a review of mobile positive pressure ventilation fans for use in rescue operations available on the European market in correlation with the approval regulations of the drive units. The authors determined the approval limits for harmful compound emissions by their power units, as applicable within the European Union. The purpose of this paper is to estimate the emissions of harmful compounds from the exhausts of rescue fan power units. It was demonstrated that electric fans are not in direct competition with internal combustion fans because they are provided in different power ranges, and 74% of the electric fan market falls between 1.1 kW and 2.2 kW, whereas fans powered by combustion engines are offered in a much higher power range from 0.7 kW to 92 kW, and the most popular power range offered by manufacturers is from 3.4 kW to 6.3 kW (57% of the market). On the basis of the limits derived from approval tests it can be demonstrated that 90% of engines on the European market which are used in fans (spark ignition (SI) engine up to 19 kW) are allowed carbon monoxide (CO) emissions of 610 g/kWh and hydrocarbon and nitrogen oxide emissions (HC + NOx) of 8 g/kWh.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.