Microstructure and Thermomechanical Properties of Magnesium Alloys Castings Magnesium alloys thanks to their high specific strength have an extensive potential of the use in a number of industrial applications. The most important of them is the automobile industry in particular. Here it is possible to use this group of materials for great numbers of parts from elements in the car interior (steering wheels, seats, etc.), through exterior parts (wheels particularly of sporting models), up to driving (engine blocks) and gearbox mechanisms themselves. But the use of these alloys in the engine structure has its limitations as these parts are highly thermally stressed. But the commonly used magnesium alloys show rather fast decrease of strength properties with growing temperature of stressing them. This work is aimed at studying this properties both of alloys commonly used (of the Mg-Al-Zn, Mn type), and of that ones used in industrial manufacture in a limited extent (Mg-Al-Sr). These thermomechanical properties are further on complemented with the microstructure analysis with the aim of checking the metallurgical interventions (an effect of inoculation). From the studied materials the test castings were made from which the test bars for the tensile test were subsequently prepared. This test took place within the temperature range of 20°C - 300°C. Achieved results are summarized in the concluding part of the contribution.
The article is focused on thermomechanical and plastic properties of two high-manganese TRIPLEX type steels with an internal marking 1043 and 1045. Tensile tests at ambient temperature and at a temperature interval 600°C to 1100°C were performed for these heats with a different chemical composition. After the samples having been ruptured, ductility was observed which was expressed by reduction of material after the tensile test. Then the stacking fault energy was calculated and dilatation of both high-manganese steels was measured. At ambient temperature (20°C), 1043 heat featured higher tensile strength by 66MPa than 1045 heat. Microhardness was higher by 8HV0,2 for 1045 steel than for 1043 steel (203HV0,2). At 20°C, ductility only differed by 3% for the both heats. Decrease of tensile properties occurred at higher temperatures of 600 up to 1100°C. This tensile properties decrease at high temperatures is evident for most of metals. The strength level difference of the both heats in the temperature range 20°C up to 1100°C corresponded to 83 MPa, while between 600°C and 1100°C the difference was only 18 MPa. In the temperature range 600°C to 800°C, a decrease in ductility values down to 14 % (1045 heat), or 22 % (1043 heat), was noticed.This decrease was accompanied with occurrence of complex Aluminium oxides in a superposition with detected AlN particles. Further ductility decrease was only noted for 1043 heat where higher occurrence of shrinkage porosity was observed which might have contributed to a slight decrease in reduction of area values in the temperature range 900°C to 1100°C, in contrast to 1045 heat matrix.
Lately we encounter still more new applications of metallic foams, as well as possible methods of their manufacture. These metallic materials have specific properties, such as large rigidity at low density, in some cases high thermal conductivity, capability to absorb energy, etc. The work is focused on the preparation of these materials using conventional casting technology, which ensures rapid and economically feasible method for production of shaped components. In the experimental part we studied conditions of casting of metallic foams with a regular structure made of ferrous and non-ferrous alloys. For thus obtained castings we evaluated the achieved microstructure and mechanical properties, which determine the possible use of these materials. The samples were subjected to compression tests, by which we investigated deformation behaviour of selected materials and determined the value of energy absorption.
The presented paper is focused on the study of refining aluminium-alloy melts. The quality of castings is determined by the basic material, i.e., the input material (furnace charge), its subsequent melting and subsequent metallurgical modifications. To allow the profitability of production, low-quality input materials are currently used, which, although they have the required chemical composition, may contain a large amount of impurities, coming not only from the original input materials, but also from their processing. To allow a cost reduction, in addition to rejected castings, the residues of gating and chipping from the machining are used as charge materials in foundries. However, the melt thus prepared is heavily contaminated with gases and inclusions.The aim of the research was, therefore, to verify the use of graphite rotors functioning as degassing units for refining aluminium melts. The experiments were conducted under laboratory and pilot-plant conditions using the plant equipment. The refining efficiency was monitored with respect to the type and shape of the graphite rotor and the refining medium used. The achieved purity of the resulting melt was evaluated to establish the density index and the final cast microstructure.
Casting Routes for Porous Metals Production The last decade has seen growing interest in professional public about applications of porous metallic materials. Porous metals represent a new type of materials with low densities, large specific surface, and novel physical and mechanical properties, characterized by low density and large specific surface. They are very suitable for specific applications due to good combination of physical and mechanical properties such as high specific strength and high energy absorption capability. Since the discovery of metal foams have been developed many methods and techniques of production in liquid, solid and gas phases. Condition for the use of metal foams - advanced materials with unique usability features, are inexpensive ways to manage their production. Mastering of production of metallic foams with defined structure and properties using gravity casting into sand or metallic foundry moulds will contribute to an expansion of the assortment produced in foundries by completely new type of material, which has unique service properties thanks to its structure, and which fulfils the current demanding ecological requirements. The aim of research conducted at the department of metallurgy and foundry of VSB-Technical University Ostrava is to verify the possibilities of production of metallic foams by conventional foundry processes, to study the process conditions and physical and mechanical properties of metal foam produced. Two procedures are used to create porous metal structures: Infiltration of liquid metal into the mold cavity filled with precursors or preforms and two stage investment casting.
The aim of this paper is to summarize the possibilities of foundry methods for the production of metallic foams. At present, there are a number of production technologies for this interesting material, to which increasing attention has been paid in recent years. What is unique about metallic foams is the combination of their physical and mechanical properties. As part of our research, we designed and verified four main methods of metallic foam production by the foundry technology, whose products are metallic foam castings with regular and irregular arrangements of internal cavities. All these methods use materials and processes commonly used in conventional foundry technologies. The main idea of the research is to highlight such technologies for the production of metallic foams that could be provided by manufacturing companies without the need to introduce changes in production. Moreover, foundry methods for the production of metallic foams have the unique advantage of being able to produce even complex shaped parts and can thus be competitive compared to today’s established technologies, the output of which is usually only a semi-finished product for further processing. This fact was the main motivation for the research.
Metallic foams are the materials, the research of which is still ongoing, with a broad applicability in many different areas (e.g., automotive industry, building industry, medicine, etc.). These materials have interesting potentials due to a combination of properties, which are, on the one hand, related to their metallic character and, on the other hand, to the porous structure. Since the discovery of porous metallic materials numerous methods of production have been developed. This work deals with the optimization of the foundry method for the manufacture of metallic foams using the evaporable polymeric pattern. This technology was used for the manufacture of metallic foams with an irregular cell structure and with fully open pores. Attention, in the experimental part, is devoted particularly to the chosen moulding material -plaster. We checked the suitably of the proposed procedure of manufacturing a plaster mould, the drying process and the subsequent annealing that significantly influence the final properties of the mould and, therefore, the quality of the resulting casting of the metallic foam. Keywords: metallic foams, casting, irregular cell structure, plaster, annealing Kovinske pene so materiali, ki se {e preiskujejo in imajo {iroko podro~je uporabnosti na razli~nih podro~jih (npr. avtomobilska industrija, gradbena industrija, medicina in podobno). Ti materiali so perspektivni zaradi kombinacije lastnosti, ki imajo po eni strani kovinske lastnosti, po drugi pa porozno strukturo. Od odkritja poroznih kovinskih materialov so se razvile {tevilne metode njihove izdelave. Delo obravnava optimizacijo livarske metode izdelave kovinske pene z uporabo izparljivega polimernega modela. Ta tehnologija je bila uporabljena za izdelavo kovinske pene z nepravilno celi~no strukturo in popolnoma odprtimi porami. V eksperimentalnem delu je pozornost usmerjena v izbiro mavca kot materiala za model. Preverjen je bil predlagani postopek izdelave mav~nega modela, postopka su{enja in`arjenja, ki imajo najve~ji vpliv na kon~ne lastnosti modela in na kvaliteto ulivanja kovinske pene.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.