The last ~4.5 years have been the most exciting and challenging period in my life so far. I want to use this opportunity to thank at least some of the people who have supported me in one way or another during this period. I wish to express my gratitude to my supervisor Dr. Morten G. Aarra; thank you for sharing your knowledge with me, for your personal encouragement, and for the many good discussions. My co-supervisor, Professor Arne Skauge, deserves a special thank as well; thank you for scientific advice and assistance throughout the work, for giving me the opportunity to participate as a Master and PhD student at Uni CIPR, and for offering me a permanent position thereafter. Acknowledge goes to Hege Ommedal for her support as PhD-coordinator at the department of Chemistry. I am also thankful to other past and present colleagues at Uni CIPR who have made this time
Foam has been applied to improve sweep during gas injection or for gas shut-off, and also for cleaning of contaminated underground formations. In this paper, foam properties have been evaluated for applications in carbonate material. The emphasis has been to investigate CO 2 foam, and therefore, methane and CO 2 based foam has been compared. Several foam experiments have been performed at high temperature and high pressure, respectively 100 o C and 277 bars in Limestone outcrop and carbonate reservoir cores. The foams ability to block or reduce mobility of unwanted gas and water is also target of the investigation.The surfactant, C 14/16 Alpha Olefin Sulfonate (AOS), ability to generate foam was influenced by the salinity of the injection water. Moderate to strong foam was generated both for CO 2 and CH 4 foams in limestone core material using 0.5 wt% surfactant concentration at seawater salinity. Mobility reduction factors at end of experiments for the different core floodings were in the range of ~ 13 to 43. The generated foams showed good ability to reduce gas and water production at low pressure gradients. In high saline formation water foam formation failed in limestone outcrop core material.For the carbonate reservoir core material, foam generation was influenced by the injection method. The preferred injection would be co-injection of gas and surfactant solution, but this method failed to generate foam. However, when pregenerated foam was injected, CO 2 foam was observed at the outlet end of the reservoir core.
Waterflooding and polymer assisted waterflood in heavy oil reservoirs has currently gaining great attention. Enhanced water injection schemes represent an alternative in cases where thermal methods are either impractical or uneconomic. This study describes and analyses the oil mobilization by imaging the oil displacement at adverse mobility by injection of brine and polymer. The objectives were to improve description of viscous instabilities, mechanisms for finger growth, water channeling at adverse mobility ratio, and oil mobilization by polymers.Experiments have been made on 2D (30cmx30cm Bentheimer slabs) studying waterflooding and tertiary polymer injection in extra heavy oils (2000cp and 7000cp). The sandstone represents a relatively homogeneous and high permeability porous medium. The experiments utilize gamma and X-ray source for porosity and saturation measurements, and an X-ray imaging system to visualize displacements and thereby quantify the underlying flow mechanisms and oil recovery.At water wet condition capillary smears the front and prevents viscous fingers even at high adverse viscosity ratio. Changes in wettability (aging the rock material) dampen the capillarity and fingers then become more pronounced. High microscopic recovery to waterfloods (up to 30% after 5 PV injected) were achieved, and most importantly a rather impressive further gain in oil recovery after polymer flooding reaching final recoveries of more than 60%. The waterflood creates multiple thin sharp fractal-like fingers that propagate in the Bentheimer sandstone material. The 2D X-ray imaging describes the finger formation, growth, and also the later water channels formed. Polymer injection gives a fast increase in oil production, and analysis from the imaging proves that the oil is mainly produced through the established water channels.The 2-D experiments demonstrate the mechanisms of how heavy oil is mobilized by polymer injection. Saturation maps were accurately measured by means of X-ray scans and this enabled the visualization of flow instability, establishment of water channels and oil mobilization with high resolution.
Polymer injectivity is a critical parameter for implementation of polymer flood projects. An improved understanding of polymer injectivity is important in order to facilitate an increase in polymer EOR implementation. Typically, injectivity studies are performed using linear core floods. Here we demonstrate that polymer flow in radial and linear models may be significantly different and discuss the concept in theoretical and experimental terms. Linear core floods using partially hydrolyzed polyacrylamides (HPAM) were performed at various rates to determine in-situ viscosity and polymer injectivity. Radial polymer floods were performed on Bentheimer discs (30 cm diameter, 2-3 cm thickness) with pressure taps distributed between a central injector and the perimeter production well. The in-situ rheological data are also compared to bulk rheology. The experimental set up allowed a detailed analysis of pressure changes from well injection to production line in the radial models and using internal pressure taps in linear cores. Linear core floods show degradation of polymer at high flow rates and a severe degree of shear thickening leading to presumably high injection pressures. This is in agreement with current literature. However, the radial injectivity experiments show a significant reduction in differential pressure compared to the linear core floods. Onset of shear thickening occurs at significantly higher flow velocities than for linear core floods. These data confirm that polymer flow is significantly different in linear and radial flow. This is partly explained by the fact that linear floods are being performed at steady state conditions, while radial injections go through transient (unsteady state) and semi-transient pressure regimes. History matching of polymer injectivity was performed for radial injection experiments. Differences in polymer injectivity are discussed in the framework of theoretical and experimental considerations. The results may have impact on evaluation of polymer flood projects as polymer injectivity is a key risk factor for implementation.
There have been several foam field applications in recent years. Foam treatments targeting gas mobility control in injectors as well as gas blocking in production wells have been performed without causing operational problems. The most widely used injection strategy of foam has been injecting alternating slugs of surfactant in brine with gas injection. This procedure seems to be beneficial as injection is easy to perform and control below fracturing pressure. Simultaneous injection of surfactant solution and gas may give difficulties, especially with interpretation of the tests, if fracturing pressure are exceeded during the injection period. This paper reviews critical aspects of foam for reservoir applications and intends to motivate for further field trials. Key parameters for qualification of foam are: foam generation, propagation in porous medium, foam strength and stability of foam. Stability is discussed, especially in the presence of oil at reservoir conditions. Data on each of these topics are included, as well as extracted summary of relevant literature. Experimental studies have shown that foam is generated at low surfactant concentration even below the CMC (critical micelle concentration). Results indicate that in situ foam generation in porous medium may depend on available nucleation sites. In situ generation of foam is complex and has been found to be especially difficult in oil wet carbonate rocks. Foam propagation in porous medium has been summarized, and propagation rate for a given experiment seems to be constant with time and distance. Laboratory studies confirm a propagation rate of 1-3 m/day. Field tests performed have not given reliable information of foam propagation rate, and future field pilots are encouraged to include observation wells in order to gain information of field-scale foam propagation. Foam strength is generally high with all gases. The exception is CO 2 at high pressure where CO 2 becomes supercritical. Stability of foam has been studied in laboratory and field tests, and has confirmed long-term stability of foam.
Polymer flooding in very viscous oil has been gaining interest since its efficiency has been field proven. Multiple laboratory investigations have evidenced that the incremental oil recovered by the tertiary process increases considerably the recovery reached thanks to water flooding. However, such tertiary injection is made all the more complex that it is preceded by unstable displacement of oil by water. Therefore a better understanding of the physics is needed, in order to better predict and optimize the viscous oil reserves associated with tertiary polymer flooding. This work presents the interpretation of three similar tertiary polymer flood experiments carried out at the Centre for Integrated Petroleum Research (CIPR, Norway). Each experiment consisted in a water flood followed by a polymer flood. They involved the same Bentheimer outcrop sandstone, 2000 cP oil, 70 cP polymer solution, 2D slab geometry, but different slab lengths (2 slabs are 30cmx30cm, 1 slab is 30cmx90cm). Saturation evolution was monitored by X-ray. On the one hand, provided simple simulation assumptions, the three water floods under study could be history matched (production, pressure). Similar ratios between water and oil relative permeabilities were found, although the water flood relative permeabilities, matched with non Corey-type curves, reflected an important variability. On the other hand, the tertiary polymer floods were found challenging to match consistently. In particular, using classic history matching approaches, the history matching of the long slab experiment could not be reconciled with that of short slab experiments. Simulations were initialized with saturation maps obtained at the end of the water floods. None of the tested approaches enabled us to match consistently the short and long slab experiments together, unless a hysteresis model was implemented. Indeed, a memory effect was observed experimentally from the quantitative analysis of X-ray saturation maps and interpreted as a hysteresis phenomenon. This simple model, with two additional matching parameters, is then further validated by the comparison of 2D simulations with measured in situ saturations.
Polymer flooding is a mature EOR technology, but several pore scale phenomena with possible large influence on the reservoir scale are poorly understood. This paper describes and analyses oil mobilization experiments of heavy oils by imaging instable displacement at adverse mobility ratio water and polymer floods. Two-dimensional flood experiments have been performed using Bentheimer outcrop slabs. X-ray imaging is utilized to visualize displacements and to determine the underlying flow mechanisms. Viscous fingering, water channel formation and oil displacement are described for a series of mobility ratios. Mechanistic understanding of development and propagation of viscous fingers at adverse mobility ratio may be used to improve reservoir simulations. Description of oil mobilization for various mobility ratios may give guidelines for choice of polymer concentration and slug size for polymer floods. Bentheimer slabs were drained using oils with 4 viscosities (5 − 616 mPa∙s). X-ray imaging revealed differences in water-finger formation, and width and growth of fingers with increasing mobility ratio. Lower mobility ratios showed formation of wide fingers or water channels. Oil recovery was dominated by propagation of these channels, but still showed poor sweep efficiency (water breakthrough 0.3 – 0.5 PV). At high mobility ratio, water breakthrough occurred very early at 0.08 – 0.15 PV. Here, the oil recovery mechanism was totally different. Oil was mobilized by polymer injection through cross-flow into the water channels. Polymer flood showed rapid change in oil cut and high total oil recovery efficiency. Through analysis of 2D x-ray images, mechanisms for fingering initiation and propagation and for oil mobilization by polymer is visualized and discussed as a function of mobility ratio. The results presented here may impact polymer flood design, in particular the choice of polymer injection strategy for heavy oil reservoirs. Data show that relatively low polymer concentrations are sufficient for mobilizing heavy oil.
Displacement tests in sandstone cores have been applied to quantify formation of foam and the gas blocking ability of water continuous foams witti polymer additives . The different chemical properties of polymers and their interactions witti surfactants made it intergisting to test botte biopolymers and syrithetic polymers . Love mobility foams veere generated botte in Berea and reservoir corgi material witti AOS baserf foams . The formation of foam witti alphaolefinsulfonate surfactant was little influenced by polymer additives as indicated by similar foam propertjes throughout the corgi . The gas blocking ability of the foams was improved witti polymer.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.