AbstrAct:The aim is to conduct experimental measurements and analyses of physical and mental workload of harvester operators. Among other things, monitoring and analyses of work conditions and workload help reduce possible risks, injuries and long-term illnesses caused by occupational stress. The interim results of the presented ergonomic study describe and analyse the course of physical load upon performing selected work operations at the stage of timber harvesting in laboratory conditions at the harvester simulator. The authors study particularly the relations between independent variables (work operations) and dependent variables (pulse, respiration and muscle tension). The diagnostic system Biofeedback 2000x-pert is used for measuring and recording changes in dependent variables. Results presented in this study analyse the obtained differences in measurements of physical and mental load in operators in individual work operations. The null hypothesis about the non-existence of a difference between the working operations from the viewpoint of the monitored variables can be refused. Therefore we can accept the hypothesis stating that there is a significant difference between individual working operations.

Harvesters produce one third of timber in Czechia. The aim of this study was to analyze the over- and under-bark volume estimates of Scots pine (Pinus sylvestris L.) timber produced by a mid-performance harvester. The data were collected between March 2017 and June 2018. In total, 4661 stems cut into 29,834 logs were analyzed. For volume estimation, StanForD offers several price categories using various algorithms. Three of these price categories are relevant for Czech forestry—M3s, M3toDE, and M3miDE. The M3s price category is based on the estimation of partial volumes of 10 cm long sections, which are summed. Therefore, this price category represents the volume estimation closest to the true volume. By comparison, the M3toDE and M3miDE price categories use the same algorithm for volume estimation, which is based on the Huber formula using a midspan diameter rounded down to the nearest whole centimeter. The M3toDE price category underestimated the over-bark volume by 6.48% compared to the reference price category M3s. The mean log volume estimated through the M3s price category was significantly higher than the M3toDE volume both in individual grades and without grading. We found significant differences between under-bark volume estimates by the diameter band bark deduction method (DBM) and the parametric linear bark deduction method (PLM) used in harvester’s systems according to the Guidelines for Electronic Scaling of Timber for Harvesters in Czechia (GEH) for Scots pine butt logs with rough bark, and also for other logs with normal bark thickness. To obtain under-bark volume estimates of Scots pine timber that are comparable with the Guidelines for Timber Scaling in Czechia (GTS) using the parametric nonlinear bark deduction method (PNM), we recommend using the algorithm of the M3toDE price category, with double bark thickness determined by the diameter band bark deduction method.

ABSTRACT:The paper deals with reliability of forest harvesters. They are quite modern and helpful in the process of tree felling. The quality of felling is important for the further quality of wood used in wood processing industry. The quality of machines is connected with time for which a machine is able to operate without any breaks caused by repairs and failures. Maintenance is the way how to realize and extend the time for reliability of machines used in felling. This research has shown how to decrease the costs of maintenance, time for its execution, manage the store of spare parts and finally increase profits of felling companies. The research has confirmed that the observation of reliability is very useful regarding the quality of maintenance and its costs. The importance of harvesters in the forest economy increases because it brings profit.

Timber is the most important source of revenue in forestry and, therefore, is necessary to precisely estimate its volume. The share of timber volume produced by harvesters is annually growing in many European countries. Suitable settings of harvesters will allow us to achieve the most accurate volume estimates of the produced timber. In this study, we compared the different methods of log volume estimation applied by control and information systems of harvesters. The aim was to analyze the price categories that can be set up in the StanForD standard and to determine the differences between the algorithms used for log volume estimations. We obtained the data from *.STM files collected from March 2017 until June 2018 on a medium-size harvester. We analyzed price categories and found seven different algorithms used to estimate the log volumes. Log volume estimates according to Algorithm A2 were considered as standard because these estimates should be closest to the true log volumes. Significant differences, except the difference between Algorithm A2 and Algorithm A3, were found between log volumes estimated by different algorithms. After categorization of logs to assortments, the results showed that significant differences existed between algorithms in each assortment. In the roundwood assortment, which contains the most valuable logs, a difference of more than 6% was found between the log volumes estimated by Algorithm A5 and Algorithm A2. This is interesting because Algorithm A5 is widely used in some Central European countries. To obtain volumes closest to the true volumes, we should use Algorithm A2 for the harvester production outputs. The resulting differences between the algorithms can be used to estimate the volume difference between harvester outputs using the different price categories. Understanding this setting of harvesters and the differences between the price categories will provide users useful information in applied forest management.

No abstract

No abstract

Our research aimed to quantify stress load in drivers by monitoring the load on the radial extensor carpi radialis (musculus extensor carpi radialis) on different types of forest and other categories of roads. We observed changes in the electrical potential of skeletal muscles using electromyographic measurements and changes in heart rate using a Biofeedback 2000 x-pert recorder. We measured the loading of drivers during the normal operation of timber trucks and timber trucks with trailers, while the reference measurements took place in a passenger car. We obtained descriptive statistics from the individual measurements and evaluated the normality of the measured data. Differences in muscle load increased when driving on lower-grade roads. The muscle load increased significantly, especially when passing through villages, inversely proportional to the width of the roads and the radius of their bends. Experiments revealed that the drivers of loaded vehicles who drove on lower-grade roads were under higher stress. Muscle load of drivers a loaded timber truck with a trailer was more difficult on roads of lower grades than on roads of grade I by 41.3%. Driving a timber truck is 21.9% more difficult on lower grade roads than on grade I roads. For preventive health and safety reasons, it is optimal to alternate trucking with a different type of work, thus minimizing the chance of occurrence of health disabilities.

Cut-to-length (CTL) operations are expanding in Central European bio-economies. However, they are costly, so efficiency must be maximized. The objective of this study was to analyze direct operational costs of three forwarders from the year 2006 until 2019. Annual amortization, services, materials, and personnel costs were analyzed and compared through ANOVA, trends were analyzed through linear regression. Forwarders LVS 5, John Deere 1010, and John Deere 1110E were deployed in coniferous forest stands with a mean stem volume between 0.10 and 0.84 m3/stem, forwarding distance between 261 and 560 m. The machines forwarded between 4045 and 34,604 m3 of timber per year, over operational times between 490 and 3896 MH (machine hours)/year, reaching machine utilization between 58% and 89%, machine productivity between 3.5 and 12.3 m3/MH, and costs between 20.95 and 84.39 €/MH. The most substantial were personnel costs (35 to 66% of the total costs), followed by materials (14.9–27.1%), amortization (12.5–15.7%), and services (3.3–22.1%). Differences between total operational costs per m3 of machines with different engine powers were not observed.