Recent experiments at ASDEX Upgrade have achieved advanced scenarios with high β N (>3) and confinement enhancement over ITER98(y, 2) scaling, H H98y2 = 1.1-1.5, in steady state. These discharges have been obtained in a modified divertor configuration for ASDEX Upgrade, allowing operation at higher triangularity, and with a changed neutral beam injection (NBI) system, for a more tangential, off-axis beam deposition. The figure of merit, β N H ITER89-P , reaches up to 7.5 for several seconds in plasmas approaching stationary conditions. These advanced tokamak discharges have low magnetic shear in the centre, with q on-axis near 1, and edge safety factor, q 95 in the range 3.3-4.5. This q-profile is sustained by the bootstrap current, NBI-driven current and fishbone activity in the core. The off-axis heating leads to a strong peaking of the density profile and impurity accumulation in the core. This can be avoided by adding some central heating from ion cyclotron resonance heating or electron cyclotron resonance heating, since the temperature profiles are stiff in this advanced scenario (no internal transport barrier). Using a combination of NBI and gas fuelling line, average densities up to 80-90% of the Greenwald density are achieved, maintaining good confinement. The best integrated results in terms of confinement, stability and ability to operate at high density are obtained in highly shaped configurations, near double null, with δ = 0.43. At the highest densities, a strong reduction of the edge localized mode activity similar to type II activity is observed, providing a steady power load on the divertor, in the range of 6 MW m −2 , despite the high input power used (>10 MW).

Reflectometry with wavelengths in the centimetre to millimetre-wave range will be used in ITER to measure the density profile in the main plasma and divertor regions and to measure the plasma position and shape in order to provide a reference for the magnetic diagnostics in long pulses. In addition, it is expected to provide key information for the measurement of density fluctuations. A set of reflectometers to meet the relevant ITER measurement requirements has been included in its present outline as part of the ITER design since 2001 and is being adapted to the present ITER baseline and to accommodate progress with reflectometry techniques and measurement capabilities. It comprises low and high field side (HFS and LFS, respectively) ordinary (O-) mode systems for the measurement of the density profile in the gradient regions, a LFS extraordinary (X-) mode system for the detailed study of the edge profile, an HFS X-mode system operating in the left hand cutoff to measure the core profile, a dedicated O-mode system for plasma-wall gap measurement and a multi-band, multiple line of sight O-mode system to measure divertor density profiles. This paper describes the evolution of the design, in particular some recent improvements in the engineering implementation and improvements aimed at enhancing the measurement capability. It concludes with a brief assessment of the likely measurement performance against the ITER measurement requirements for the parameters of interest and the overall confidence that the technique will be implanted on ITER.

ASDEX Upgrade has recently finished its transition towards an all-W divertor tokamak, by the exchange of the last remaining graphite tiles to W-coated ones. The plasma start-up was performed without prior boronization. It was found that the large He content in the plasma, resulting from DC glow discharges for conditioning, leads to a confinement reduction. After the change to D glow for inter-shot conditioning, the He content quickly dropped and, in parallel, the usual H-Mode confinement with H factors close to one was achieved. After the initial conditioning phase, oxygen concentrations similar to that in previous campaigns with boronizations could be achieved. Despite the removal of all macroscopic carbon sources, no strong change in C influxes and C content could be observed so far. The W concentrations are similar to the ones measured previously in discharges with old boronization and only partial coverage of the surfaces with W. Concomitantly it is found that although the W erosion flux in the divertor is larger than the W sources in the main chamber in most of the scenarios, it plays only a minor role for the W content in the main plasma. For large antenna distances and strong gas puffing, ICRH power coupling could be optimized to reduce the W influxes. This allowed a similar increase of stored energy as yielded with comparable beam power. However, a strong increase of radiated power and a loss of H-Mode was observed for conditions with high temperature edge plasma close to the antennas. The use of ECRH allowed keeping the central peaking of the W concentration low and even phases of improved H-modes have already been achieved.

A reflectometry system has been developed for ASDEX Upgrade to measure the plasma profile from the scrape-off layer until the bulk plasma, simultaneously at the high and low field sides. Unique features of the system are the ultrafast broadband frequency modulation of a continuous wave using solid state stable hyper abrupt tuned oscillators (down to 10 μs), high and low field side channels and fully remote control operation, via optical fiber links. Due to the special design of the transmission line, with decoupled in going and out going lines and one-antenna configuration, the system is optimized for reception and spurious reflections are eliminated. The ultrafast operation guarantees that the effect of plasma turbulence is greatly reduced. Both features determine the high performance of the diagnostic. A dedicated data acquisition system handles the large amounts of data generated by the broadband operation. Recent developments include the operation of new channels and an automatic and accurate frequency calibration circuit. Also, advanced digital signal processing techniques were applied to obtain density profiles with high spatial and temporal (20 μs) resolutions under turbulent plasma regions, e.g., the scrape-off layer. Experimental results are presented showing the great sensitivity of the diagnostic to plasma radial movements and its tolerance to vertical movements of the plasma. Density profiles measured in ELMy regimes illustrate the capabilities of the diagnostic to detect fast profile changes.

The ASDEX Upgrade (AUG) programme is directed towards physics input to critical elements of the ITER design and the preparation of ITER operation, as well as addressing physics issues for a future DEMO design. Since 2015, AUG is equipped with a new pair of 3-strap ICRF antennas, which were designed for a reduction of tungsten release during ICRF operation. As predicted, a factor two reduction on the ICRF-induced W plasma content could be achieved by the reduction of the sheath voltage at the antenna limiters via the compensation of the image currents of the central and side straps in the antenna frame. There are two main operational scenario lines in AUG. Experiments with low collisionality, which comprise current drive, ELM mitigation/suppression and fast ion physics, are mainly done with freshly boronized walls to reduce the tungsten influx at these high edge temperature conditions. Full ELM suppression and non-inductive operation up to a plasma current of I p = 0.8 MA could be obtained at low plasma density. Plasma exhaust is studied under conditions of high neutral divertor pressure and separatrix electron density, where a fresh boronization is not required. Substantial progress could be achieved for the understanding of the confinement degradation by strong D puffing and the improvement with nitrogen or carbon seeding. Inward/outward shifts of the electron density profile relative to the temperature profile effect the edge stability via the pressure profile changes and lead to improved/decreased pedestal performance. Seeding and D gas puffing are found to effect the core fueling via changes in a region of high density on the high field side (HFSHD). The integration of all above mentioned operational scenarios will be feasible and naturally obtained in a large device where the edge is more opaque for neutrals and higher plasma temperatures provide a lower collisionality. The combination of exhaust control with pellet fueling has been successfully demonstrated. High divertor enrichment values of nitrogen E N ⩾ 10 have been obtained during pellet injection, which is a prerequisite for the simultaneous achievement of good core plasma purity and high divertor radiation levels. Impurity accumulation observed in the all-metal AUG device caused by the strong neoclassical inward transport of tungsten in the pedestal is expected to be relieved by the higher neoclassical temperature screening in larger devices.

The results of divertor studies on ASDEX Upgrade, at currents of up to 1.2 MA and heating powers up to 10 M W are described, with emphasis on the ELMy H-mode. The spatial and temporal characteristics of their heat load, and the simulation of ELMs by a time-dependent scrape-off layer code are described. High gas puff rata were found to lead to a large increase in divertor neutral pressure, at modest changes in %, and to a strong reduction in timeaveraged power flow and complete detachment from both target plates in between ELMs. Using pre-programmed puffs of neon and argon, the radiative power losses could be raised to 75% of the heating power, in H-regime discharges, and the regime of enhanced divertor neutral pressure was found also to lead to an improved pumping of recycling impurities. 1.Introduction:ASDEX Upgrade is a mid-size tokamak w i t h non-circular cross-section (major radius R, , = 1.625m, horizontal minor radius a = 0.5 m, elongation b/a = 1.6), purpose-designed as a poloidal divertor device (Figure 1). Further distinguishing features of it are the poloidal field coils placed outside the toroidal ones, and the presence of a saddle coil ("PSL" .. pssive Stabilising loop) inside the vacuum vessel for stabilising the vertical displacement instability. Together, these two features provide a relatively large space between the vacuum vessel and the X-point of the poloidal field lines, although the present divertor configuration, selected to optimise the heat load distribution, places the target plates relatively close to the x-point.

The contribution of the initial plasma to density profiles reconstructed from the dφ/df vs f curve obtained with reflectometry is studied. It is shown that the initial phase information determines to a great extent the accuracy of the inverted profiles at the edge. As it is difficult to measure the edge contribution models are required to initialize the profile evaluation. A novel method is presented that uses the phase information from the lowest frequency waves to obtain dφ/df below the first probing frequency F1, by imposing the continuity with the measured dφ/df characteristic and its derivative at F1. An approximate shape of the edge profile is obtained because low-frequency waves are sensitive to the initial plasma where they propagate without reflection. The accuracy of the inverted profiles is thereby improved, as shown by simulation studies performed for profiles with an exponential-like decay and with an edge density plateau (typical of H-mode regimes during ELMs). It is found that the contribution from the initial plasma decreases with density (or frequency); for densities of the order of 10× the first probed density ne1 it is reduced to values less than 10% in the case of a profile with a flat edge and 2% for a peaked one. For ne≳10ne1 the profiles can be absolutely calibrated from reflectometry data alone with an accuracy of ±2 mm independent of the initialization model. The numerical study also shows that profile deviations resulting from insufficient phase derivative data, e.g., due to discrete probing, can be more significant than those originated by the initialization process.

The medium size divertor tokamak ASDEX Upgrade (major and minor radii 1.65 m and 0.5 m, respectively, magnetic-field strength 2.5 T) possesses flexible shaping and versatile heating and current drive systems. Recently the technical capabilities were extended by increasing the electron cyclotron resonance heating (ECRH) power, by installing 2 × 8 internal magnetic perturbation coils, and by improving the ion cyclotron range of frequency compatibility with the tungsten wall. With the perturbation coils, reliable suppression of large type-I edge localized modes (ELMs) could be demonstrated in a wide operational window, which opens up above a critical plasma pedestal density. The pellet fuelling efficiency was observed to increase which gives access to H-mode discharges with peaked density profiles at line densities clearly exceeding the empirical Greenwald limit. Owing to the increased ECRH power of 4 MW, H-mode discharges could be studied in regimes with dominant electron heating and low plasma rotation velocities, i.e. under conditions particularly relevant for ITER. The ion-pressure gradient and the neoclassical radial electric field emerge as key parameters for the transition. Using the total simultaneously available heating power of 23 MW, high performance discharges have been carried out where feed-back controlled radiative cooling in the core and the divertor allowed the divertor peak power loads to be maintained below 5 MW m−2. Under attached divertor conditions, a multi-device scaling expression for the power-decay length was obtained which is independent of major radius and decreases with magnetic field resulting in a decay length of 1 mm for ITER. At higher densities and under partially detached conditions, however, a broadening of the decay length is observed. In discharges with density ramps up to the density limit, the divertor plasma shows a complex behaviour with a localized high-density region in the inner divertor before the outer divertor detaches. Turbulent transport is studied in the core and the scrape-off layer (SOL). Discharges over a wide parameter range exhibit a close link between core momentum and density transport. Consistent with gyro-kinetic calculations, the density gradient at half plasma radius determines the momentum transport through residual stress and thus the central toroidal rotation. In the SOL a close comparison of probe data with a gyro-fluid code showed excellent agreement and points to the dominance of drift waves. Intermittent structures from ELMs and from turbulence are shown to have high ion temperatures even at large distances outside the separatrix.