OBJECTIVE: To assess the prevalence of severe external root resorption and its potential risk factors resulting from orthodontic treatment. METHODS: A randomly selected sample was used. It comprised conventional periapical radiographs taken in the same radiology center for maxillary and mandibular incisors before and after active orthodontic treatment of 129 patients, males and females, treated by means of the Standard Edgewise technique. Two examiners measured and defined root resorption according to the index proposed by Levander et al. The degree of external apical root resorption was registered defining resorption in four degrees of severity. To assess intra and inter-rater reproducibility, kappa coefficient was used. Chi-square test was used to assess the relationship between the amount of root resorption and patient's sex, dental arch (maxillary or mandibular), treatment with or without extractions, treatment duration, root apex stage (open or closed), root shape, as well as overjet and overbite at treatment onset. RESULTS: Maxillary central incisors had the highest percentage of severe root resorption, followed by maxillary lateral incisors and mandibular lateral incisors. Out of 959 teeth, 28 (2.9%) presented severe root resorption. The following risk factors were observed: anterior maxillary teeth, overjet greater than or equal to 5 mm at treatment onset, treatment with extractions, prolonged therapy, and degree of apex formation at treatment onset. CONCLUSION: This study showed that care must be taken in orthodontic treatment involving extractions, great retraction of maxillary incisors, prolonged therapy, and/or completely formed apex at orthodontic treatment onset.

No abstract

Printed models with a regular base or a horseshoe-shaped base with a bar were accurate regardless of the printing technique used. Printed models with a horseshoe-shaped base made with the stereolithography printer had a statistically significant reduction in the transversal dimension that was not found in the models printed with the polyjet technique.

The aim of this study was to evaluate different approaches to deactivating myofascial trigger points (MTPs). Twenty-one women with bilateral MTPs in the masseter muscle were randomly divided into three groups: laser therapy, needle treatment and control. Treatment effectiveness was evaluated after four sessions with intervals ranging between 48 and 72 h. Quantitative and qualitative methods were used to measure pain perception/sensation. The Wilcoxon test based on results expressed on a visual analog scale (VAS) demonstrated a significant (P < 0.05) decrease in pain only in the laser and needle treatments groups, although a significant increase in the pressure pain threshold was evident only for needling with anesthetic injection (P = 0.0469), and laser therapy at a dose of 4 J/cm² (P = 0.0156). Based on these results, it was concluded that four sessions of needling with 2% lidocaine injection with intervals between 48 and 72 h without a vasoconstrictor, or laser therapy at a dose of 4 J/cm², are effective for deactivation of MTPs.

ObjectiveTo compare the influence of archwire material (NiTi, beta-Ti and stainless steel) and brackets design (self-ligating and conventional) on the frictional force resistance.Material and MethodsTwo types of brackets (self-ligating brackets - Smartclip, 3M/Unitek - and conventional brackets - Gemini, 3M/Unitek) with three (0, 5, and 10 degrees) slot angulation attached with elastomeric ligatures (TP Orthodontics) were tested. All brackets were tested with archwire 0.019"x0.025" nickel-titanium, beta-titanium, and stainless steel (Unitek/3M). The mechanical testing was performed with a universal testing machine eMIC DL 10000 (eMIC Co, Brazil). The wires were pulled from the bracket slots at a cross-head speed of 3 mm/min until 2 mm displacement.ResultsSelf-ligating brackets produced significantly lower friction values compared with those of conventional brackets. Frictional force resistance values were directly proportional to the increase in the bracket/ wire angulation. With regard to conventional brackets, stainless steel wires had the lowest friction force values, followed by nickel-titanium and beta-titanium ones. With regard to self-ligating brackets, the nickel-titanium wires had the lowest friction values, significantly lower than those of other materials.Conclusioneven at different angulations, the self-ligating brackets showed significantly lower friction force values than the conventional brackets. Combined with nickel-titanium wires, the self-ligating brackets exhibit much lower friction, possibly due to the contact between nickel-titanium clips and wires of the same material.

Overall, our findings showed that most of the measurements on digital models created using the TRIOS Color scanner and measured with Ortho Analyzer software had a clinically acceptable accuracy compared to the same measurements made with a caliper on plaster models, but the measuring method can affect the reproducibility of the measurements.

Objective: To evaluate the reliability of three-dimensional (3D) landmark identification in conebeam computed tomography (CBCT) using two different visualization techniques. Materials and Methods: Twelve CBCT images were randomly selected. Three observers independently repeated three times the identification of 30 landmarks using 3D reconstructions and 28 landmarks using multiplanar views. The values of the coordinates X, Y, and Z of each point were obtained and the intraclass correlation coefficient (ICC) was calculated. Results: The ICC of the 3D visualization was rated .0.90 in 67.76% and 45.56%, and #0.45 in 13.33% and 14.46% of the intraobserver and interobserver assessments, respectively. The ICC of the multiplanar visualization was rated .0.90 in 82.16% and 78.56% and #0.45 in only 16.7% and 8.33% of the intraobserver and interobserver assessments, respectively. An individual landmark classification was done according to ICC values. Conclusions: The frequency of highly reliable values was greater for multiplanar than 3D reconstructions. Overall, lower reliability was found for points on the condyle and higher reliability for those on the midsagittal plane. Depending on the anatomic region, the observer must choose the most reliable type of image visualization. (Angle Orthod. 2015;85:11-17.)

Virtual setups present several advantages, e.g., digital storage, digital models cannot be damaged, the same model can undergo several treatment simulations, and communication between dental and surgical professionals and between dental professionals and patients is facilitated. Despite these advantages, considerable time and training are needed for dental professionals to master and adopt the general use of digital models and virtual setups in dentistry.