Objective The improvement of the optical properties of new generation dental ceramics enables more esthetic and durable restorations. This study aimed to investigate the color changes, caused by exposure to different beverages on composite, hybrid ceramic, and zirconia‐reinforced lithium silicate (ZLS) CAD/CAM blocks. Materials and methods CAD/CAM blocks 40 samples (1.5 × 7 × 12 mm) were obtained from each material under water cooling. Following the polishing process and the initial color measurement, the prepared samples were exposed to red wine, coffee, cola, energy drink, and distilled water. Color changes were measured by spectrophotometer at the end of the 1st, 7th, and 30th days. To analyze the color change results, one‐way analysis of variance (ANOVA) test was performed. Results In all restorative material groups, the most prominent color changes were observed on the red wine‐exposed samples, then the coffee‐exposed ones. No significant discoloration was observed on the samples exposed to cola and energy drink, compared to the control group (P > .05). Among the samples exposed to red wine and coffee, the highest discoloration values were observed in composite CAD/CAM material. Conclusions At the end of the 30th day, all materials exposed to wine and coffee showed color change above the clinically acceptable value (ΔE00:2.25). Clinical significance Hybrid ceramic and ZLS CAD/CAM blocks recently used more often by clinicians have shown similar color changes. The results of our study indicate the necessity of choosing esthetic materials according to the dietary habits of individuals.

Aim: Although it has been stated that composite resins should be used in the restoration of teeth after color shade selection, it has recently been stated that single-shade composite resins can be used for all tooth shades. The objective of our study is to evaluate the surface roughness and color change of single-shade composite resins compared with multi-shade system composite resins. Material and methods: In our study, samples (8 mm diameter and 2 mm depth) were obtained using single-shade (Omnichrorma) and multi-shade system (Filtek Universal Restorative, Clearfil Majesty ES-2 Premium, Harmonize) composite resins. Two steps finishing and polishing system (Clearfil Twist Dia) was used in the finishing polishing processes of the samples. The initial roughness values of the samples were measured with a profilometer and color values with a spectrophotometer. Then, color measurements of the samples kept in coffee were made on the 1 st , 7 th and 30 th days and after the last polishing process. The surface roughness (Ra) and color change (ΔE00) were statistically analyzed using two-way variance analysis (ANOVA) and Tukey post-hoc test (p<0.05). Results: There was no statistically significant difference between the initial surface roughness values of composite resins with single and multi-shade systems (p>0.05). Composite resin with single-shade system showed statistically significantly more color change than composite resin with multi-shade systems in all time periods (p<0.001). Although re-polishing these materials reduced the color changes, it could not decrease it below the acceptability threshold value (ΔE00:1.8). Conclusion: New generation single-shade composite resin with smart chromatic material technology can simplify color selection without sacrificing esthetic success. However, this composite resin shows more color changes than multi-shade systems composite resins.

No abstract

Introduction Some colorant foods and beverages cause undesired discoloration on dental restorations. The aim of this study was to investigate the effect of whitening kinds of toothpaste with different active ingredients on the color change of resin‐based CAD/CAM blocks. Material and methods In the study, resin‐based CAD/CAM block samples sized 1.5 × 7 × 12 mm, were prepared. Then, to simulate the time‐dependent color change, the samples were immersed in coffee (Nescafe Classic, Nestlé) for 14 days. After the color change values of the samples colored in coffee were measured by spectrophotometer, the samples were brushed with different types of whitening toothpastes for 4 minutes. Statistical analysis of the color change (ΔE00) was performed using the one‐way analysis of variance (ANOVA). Results Color differences occurring on all resin‐based CAD/CAM blocks immersed in coffee for 14 days exceeded the 50%:50% perceptibility threshold (PT) (ΔE00:0.8). There was no statistical significant difference between the whitening toothpastes containing activated charcoal, hydrogen peroxide (HP), blue covarine pigment, and microparticles in color improvement on resin‐based CAD/CAM blocks (P > .05). Conclusion It has been verified that the discoloration on resin‐based CAD/CAM blocks exhibiting color difference above the PT after coffee immersion can be reduced by utilizing toothpastes containing whiteners. Clinical significance Color changes that occur over time in resin‐based CAD/CAM blocks can be a clinical problem. These color changes in the materials can be reduced below the PT level using whitening toothpastes.

Background High viscosity glass ionomer cement (HVGIC) and resin-modified glass ionomer cement (RMGIC) have recently been clinically preferred thanks to their numerous advantages. However, initial moisture contamination has a negative effect on the mechanical and physical properties of these cements. The aim of this study was in vitro of HVGICs and RMGICs, with and without surface protection, on water sorption, solubility and release of aluminum. Material and Methods In this study, as HVGICs; Equia Forte, IonoStar Plus, Riva Self Cure; as RMCIS, Ionolux and Riva Light Cure; and as control, Z250 universal composite was used. Equia coat, Voco varnish and Riva coat were chosen as surface protective. Water sorption and solubility levels of the samples were measured according to ISO 4049:2009. Al levels released from samples were determined by graphite furnace atomic absorption spectroscopy (GFAAS) for 7, 14 and 21 days. Statistical evaluation of the results was made using one-way variance analysis (ANOVA) and Tukey post-hoc test ( p <0.05). Results RMGICs from restorative materials showed more water absorption than HVGICs, but no differences in solubility. Among the materials tested, the water absorption values of the HVGIC and RMGIC materials without surface protection were higher than those with the surface protection ( p <0.001). Conclusions It was determined that the Al release of HVGIC and RMGIC groups with the surface protection were lower in all time periods than the groups without surface protection ( p <0.001). The application of surface protection effectively reduced water sorption and Al release from HVGICs and RMGICs. Key words: Highly viscous glass ionomer cement, resin coating, aluminum release, water sorption, solubility.

Purpose: The study aimed at evaluating the effect of wet and dry polishing systems on the resin composites’ surface roughness and color change. Materials and Methods: In the study, samples were prepared using nanoceramic (Ceram.x one) and nanohybrid (GrandioSO) resin composites. Two different finishing and polishing systems were used in the polishing of resin composites. Resin composite surfaces were finished and polished under wet and dry conditions. The initial surface roughness values (Ra) of the samples were measured using a profilometer, whereas the color changes were measured using a spectrophotometer. Then, the colors of the samples kept in coffee were measured on the 7th and 30th days. Surface roughness and color change values (ΔE00) were measured and statistically analyzed using the one-way analysis of variance (ANOVA) test ( P < .05). Results: Wet or dry use of polishing systems did not show a statistically significant difference between the surface roughness values of the resin composite ( P < .05). Wet and dry use of polishing systems showed similar color changes on the composite resins ( P < .05). Diamond-containing spirals on composite resins showed statistically less color change than aluminum-oxide-containing discs ( P < .05). Wet or dry use of polishing systems did not reduce the color change of the composite resins below the acceptability threshold (AT). Conclusion: Wet or dry use of polishing systems on composite resins did not affect surface roughness and color change. The use of diamond-containing polishing spirals that cause less color change can increase clinical success.

No abstract

Purpose: This study investigated discoloration and surface roughness (Ra) of resin-based computer aided design (CAD)/computer aided manufacturing (CAM) blocks and direct and indirect resin composites after staining with coffee. Materials & Methods: Using a Teflon mold, 60 disc shaped specimens (8×2 mm2) were fabricated from direct (Estelite Asteria and GrandioSO) and indirect (Gradia Plus) resin composites, and 30 resin CAD/CAM specimens (12×14×2 mm3) were prepared from resin composite CAD/CAM blocks (Vita Enamic, Brilliant Crios, and Cerasmart) (n=10). A contact type profilometer was used to determine the Ra of all 60 polished samples. All specimens were thermocycled between 5 and 55°C for 3000 cycles, and immersed in coffee solution (37°C) for 1 and 7 days. A spectrophotometer was used to determine the color change (∆E00) with the CIEDE2000 formula after the specimens were re-polished. One-way analysis of variance (ANOVA) and Tukey multiple comparison test was performed to analyze the data (p<0.05). Results: The lowest degree of discoloration among the materials tested was found in Vita Enamic resin CAD/CAM block (p<0.001), whereas the highest degree of discoloration was found in the Gradia Plus indirect composite (p<0.001). There was no significant difference was seen between the initial surface roughness values (Ra) among the groups (p=0.249). No significant improvement was observed in the color of the groups except for the Cerasmart resin block after after polishing. Conclusion: Direct resin composites have a higher discoloration potential over resin-based CAD/CAM blocks, whereas they are less prone to discoloration than indirect resin composites