This paper presents a study on linearly polarized compact multiband multiple-input multiple-output (MIMO) antenna system for small mobile terminals. The MIMO antenna system consists of two symmetric printed monopole antennas with edge-to-edge separation of 0.097λ0 at 900 MHz. Each antenna element has a capacitive feed and is composed of two twisted lines, a parasitic loop, and a shorting trip that generate five resonant modes around 900, 1800, 2100, 3500, and 5400 MHz, covering GSM850/900, DCS, PCS, UMTS, WLAN and WiMAX frequency bands. Two inverted-L shaped branches and a rectangular slot with one circular end, etched on the ground plane, were introduced to improve the isolation between antenna elements. The isolation achieved is higher than 15 dB in the lower band and 20 dB in the upper bands, leading to an envelope correlation coefficient of less than 0.025. The simulated performance of the designed antenna system has been verified in the experiment.Index Terms-Antenna, decoupling, envelope correlation coefficient, multiband antenna, multiple-input multiple-output (MIMO) antenna, printed monopole antenna.

This paper presents a novel design of a Multiple Input Multiple Output (MIMO) antenna system for next generation sub 6 GHz 5G and beyond mobile terminals. The proposed system is composed of a main board and two side boards. To make the design cost-effective, FR4 is used as a substrate. The design is based on a unit monopole antenna etched at the side substrate. The single element is resonating at 3.5 GHz attaining a 10 dB bandwidth of 200 MHz and a 6 dB bandwidth of 400 MHz. The single element is then transformed into an MIMO array of 8-elements with an overall dimension of 150 mm × 75 mm × 7 mm, providing pattern diversity characteristics and isolation better than −12 dB for any two radiating elements. A number of studies such as effects of human hand on the system that includes single hand mode and dual mode scenarios and the effects of Liquid Crystal Display (LCD) over the principal performance parameters of the system are presented. The envelop correlation coefficient (ECC) is computed for all the scenarios and it is found that ECC is less than 0.1 for any case and maximum channel capacity is 38.5 bps/Hz within the band of interest. The main advantage of the proposed design over available designs in the literature is that almost all of the main substrate is empty providing wide space for different sensors, systems, and mobile technology components. A brief literature comparison of the proposed system is also presented. To validate the proposed model, a prototype is fabricated and results are presented. This design can be applied on higher frequencies to future micromachines for on chip communications using same theocratical approach as the space for higher frequencies in mmwave spectrum has been reserved. The simulated results are in an excellent agreement with the measured results. All the main performance parameters of the design are calculated and compared with the measured results wherever possible.

No abstract

No abstract

This paper presents a multiple-input multiple-output (MIMO) antenna system for millimeter-wave 5G wireless communication services. The proposed MIMO configuration is composed of four antenna elements, where each antenna possesses an HP-shaped configuration that features simple configuration and excellent performance. The proposed MIMO design can operate at a very wideband of 36.83–40.0 GHz (measured). Furthermore, the proposed MIMO antenna attains a peak gain of 6.5 dB with a maximum element-isolation of −45 dB. Apart from this, the MIMO performance metrics such as envelope correlation coefficient (ECC), diversity gain, and channel capacity (CCL) are analyzed, which demonstrate good characteristics across the operating band. The proposed antenna radiates efficiently with a radiation efficiency of above 80% at the desired frequency band which makes it a potential contender for the upcoming communication applications. The proposed design simulations were performed in the computer simulation technology (CST) software, and measured results reveal good agreement with the simulated one.

No abstract

We describe a method for direct intercomparison of terahertz permittivities at 200 GHz obtained by a Vector Network Analyzer and a Time-Domain Spectrometer, whereby both instruments operate in their customary configurations, i.e., the VNA in waveguide and TDS in free-space. The method employs material that can be inserted into a waveguide for VNA measurements or contained in a cell for TDS measurements. The intercomparison experiments were performed using two materials: petroleum jelly and a mixture of petroleum jelly with carbon powder. The obtained values of complex permittivities were similar within the measurement uncertainty. An intercomparison between VNA and TDS measurements is of importance because the two modalities are customarily employed separately and require different approaches. Since material permittivities can and have been measured using either platform, it is necessary to ascertain that the obtained data is similar in both cases.

This paper presents a review of wireless power transfer (WPT) followed by a comparison between ambient energy sources and an overview of different components of rectennas that are used for RF energy harvesting. Being less costly and environment friendly, rectennas are used to provide potentially inexhaustible energy for powering up low power sensors and portable devices that are installed in inaccessible areas where frequent battery replacement is difficult, if not impossible. The current challenges in rectenna design and a detailed comparison of state-of-the-art rectennas are also presented.