A compact tree shape planar quad element Multiple Input Multiple Output (MIMO) antenna bearing a wide bandwidth for 5G communication operating in the millimeter-wave spectrum is proposed. The radiating element of the proposed design contains four different arcs to achieve the wide bandwidth response. Each radiating element is backed by a 1.57 mm thicker Rogers-5880 substrate material, having a loss tangent and relative dielectric constant of 0.0009 and 2.2, respectively. The measured impedance bandwidth of the proposed quad element MIMO antenna system based on 10 dB criterion is from 23 GHz to 40 GHz with a port isolation of greater than 20 dB. The measured radiation patterns are presented at 28 GHz, 33 GHz and 38 GHz with a maximum total gain of 10.58, 8.87 and 11.45 dB, respectively. The high gain of the proposed antenna further helps to overcome the atmospheric attenuations faced by the higher frequencies. In addition, the measured total efficiency of the proposed MIMO antenna is observed above 70% for the millimeter wave frequencies. Furthermore, the MIMO key performance metrics such as Mean Effective Gain (MEG) and Envelope Correlation Coefficient (ECC) are analyzed and found to conform to the required standard of MEG < 3 dB and ECC < 0.5. A prototype of the proposed quad element MIMO antenna system is fabricated and measured. The experimental results validate the simulation design process conducted with Computer Simulation Technology (CST) software.

This work presents a systematic design of high performance eight element antenna array for a 5G mobile terminal operating at 2.6/3.5 GHz bands. The proposed eight element slot antenna array based on unit monopole slot antenna embedded in the metal casing or ground resonates at fundamental mode at 2.6 GHz. The antenna array is developed from four antennas (open-end slot antenna) etched near to the corner edges of the printed circuited board with supported pairs of vertically mounted slot antennas in middle section of the long edge ground plane. This combination of the antenna elements provided pattern diversity and enabled the smartphone in the reception of the signal in a different direction. The impedance bandwidth based on-10 dB return loss criteria cover from 2.4 GHz to 3.6 GHz includes the two allocated bands of (2400 MHz to 2600 MHz) and (3400 MHz to 3600 MHz) for 5G cellular communication systems. The vital MIMO performance measures as envelope correlation coefficient or ECC is less than 0.2 for any two antenna array meeting the required standard of less than 0.5 alongside the mean effective gain or MEG ratio of any two antenna meeting the required standard of less than 3 dB for power balance and optimal diversity performance. As modern smartphone demand desires slim handsets, the after mentioned compact multiple antenna structure can be easily implemented for the future smartphones as it utilizes the conductive sheet or chassis and the middle vertically mounted antenna do not use the additional space of the chassis or ground. The customer hand or human hand effect on the multiple antenna array to mimic the use of mobile phone customer is also studied. The maximum MIMO Channel capacity based on measured result is 34.25bps/Hz and is about 3 times of 2 × 2 MIMO operations. INDEX TERMS Channel capacity, envelope correlation coefficient, mean effective gain, mutual coupling, slot antennas, multiple input multiple output.

In this paper, a novel single layer Multiple Input–Multiple Output (MIMO) antenna for Fifth-Generation (5G) 28 GHz frequency band applications is proposed and investigated. The proposed MIMO antenna operates in the Ka-band, which is the most desirable frequency band for 5G mm-wave communication. The dielectric material is a Rogers-5880 with a relative permittivity, thickness and loss tangent of 2.2, 0.787 mm and 0.0009, respectively, in the proposed antenna design. The proposed MIMO configuration antenna element consists of triplet circular shaped rings surrounded by an infinity-shaped shell. The simulated gain achieved by the proposed design is 6.1 dBi, while the measured gain is 5.5 dBi. Furthermore, the measured and simulated antenna efficiency is 90% and 92%, respectively. One of the MIMO performance metrics—i.e., the Envelope Correlation Coefficient (ECC)—is also analyzed and found to be less than 0.16 for the entire operating bandwidth. The proposed MIMO design operates efficiently with a low ECC, better efficiency and a satisfactory gain, showing that the proposed design is a potential candidate for mm-wave communication.

This paper presents a novel design of a Multiple Input Multiple Output (MIMO) antenna system for next generation sub 6 GHz 5G and beyond mobile terminals. The proposed system is composed of a main board and two side boards. To make the design cost-effective, FR4 is used as a substrate. The design is based on a unit monopole antenna etched at the side substrate. The single element is resonating at 3.5 GHz attaining a 10 dB bandwidth of 200 MHz and a 6 dB bandwidth of 400 MHz. The single element is then transformed into an MIMO array of 8-elements with an overall dimension of 150 mm × 75 mm × 7 mm, providing pattern diversity characteristics and isolation better than −12 dB for any two radiating elements. A number of studies such as effects of human hand on the system that includes single hand mode and dual mode scenarios and the effects of Liquid Crystal Display (LCD) over the principal performance parameters of the system are presented. The envelop correlation coefficient (ECC) is computed for all the scenarios and it is found that ECC is less than 0.1 for any case and maximum channel capacity is 38.5 bps/Hz within the band of interest. The main advantage of the proposed design over available designs in the literature is that almost all of the main substrate is empty providing wide space for different sensors, systems, and mobile technology components. A brief literature comparison of the proposed system is also presented. To validate the proposed model, a prototype is fabricated and results are presented. This design can be applied on higher frequencies to future micromachines for on chip communications using same theocratical approach as the space for higher frequencies in mmwave spectrum has been reserved. The simulated results are in an excellent agreement with the measured results. All the main performance parameters of the design are calculated and compared with the measured results wherever possible.

In this paper, the systematic design of a multiple antenna system for 5G smartphone operating at 3.5 GHz for multiple-input multiple-output (MIMO) operation in smartphones is proposed. The smartphone is preferred to be lightweight, thin, and attractive, and as a result metal casings have become popular. Using conventional antennas, such as a patch antenna, Inverted-F antennas, or monopole, in proximity to metal casing leads to decreasing its total efficiency and bandwidth. Therefore, a slot antenna embedded in the metal casing can be helpful, with good performance regarding bandwidth and total efficiency. The proposed multiple antenna system adopted the unit open-end slot antenna fed by Inverted-L microstrip with tuning stub. The measured S-parameters results agree fairly with the numerical results. It attains 200 MHz bandwidth at 3.5 GHz with ports isolation of (≤−13 dB) for any two antennas of the system. The influence of the customer’s hand for the proposed multiple antenna system is also considered, and the MIMO channel capacity is computed. The maximum achievable MIMO channel capacity based on the measured result is 31.25 bps/Hz and is about 2.7 times of 2 × 2 MIMO operation.

Multiple-input multiple-output (MIMO) scheme refers to the technology where more than one antenna is used for transmitting and receiving the information packets. It enhances the channel capacity without more power. The available space in the modern compact devices is limited and MIMO antenna elements need to be placed closely. The closely spaced antennas undergo an undesirable coupling, which deteriorates the antenna parameters. In this paper, an ultra wide-band (UWB) MIMO antenna system with an improved isolation is presented. The system has a wide bandwidth range from 2–13.7 GHz. The antenna elements are closely placed with an edge to edge distance of 3 mm. In addition to the UWB attribute of the system, the mutual coupling between the antennas is reduced by using slotted stub. The isolation is improved and is below −20 dB within the whole operating range. By introducing the decoupling network, the key performance parameters of the antenna are not affected. The system is designed on an inexpensive and easily available FR-4 substrate. To better understand the working of the proposed system, the equivalent circuit model is also presented. To model the proposed system accurately, different radiating modes and inter-mode coupling is considered and modeled. The EM model, circuit model, and the measured results are in good agreement. Different key performance parameters of the system and the antenna element such as envelope correlation coefficient (ECC), diversity gain, channel capcity loss (CCL) gain, radiation patterns, surface currents, and scattering parameters are presented. State-of-the-art comparison with the recent literature shows that the proposed antenna has minimal dimensions, a large bandwidth, an adequate gain value and a high isolation. It is worth noticeable that the proposed antenna has high isolation even the patches has low edge-to-edge gap (3 mm). Based on its good performance and compact dimensions, the proposed antenna is a suitable choice for high throughput compact UWB transceivers.

The aim of this work is to propose a dual band millimeter wave (mmwave) MIMO antenna system for 5G technology. In addition, the arrangement of the antenna elements in an array should be in such a manner that without using the traditional decoupling structures and/or techniques, a reasonable isolation level must be achieved. To demonstrate this, a system consists of four radiating elements that are etched on a 0.508 mm-thick Rogers-5880 substrate. The dielectric constant of the substrate is 2.2 and the loss tangent is 0.0009. Each radiating element consists of three parts; an E-shaped patch, an H-shaped slot within a patch, and a transmission line. The system is resonating at two different mmwave frequencies, i.e., 28 GHz and 38 GHz with a minimum port isolation of 28 dB. The mean measured gain is found to be at 7.1 dBi at 28 GHz and 7.9 dBi at 38 GHz with average efficiency, and envelope correlation coefficient (ECC) of the system at 70%, and 0.0005 respectively. The proposed system is designed and simulated in a full-wave electromagnetic wave software Computer Simulation Technology (CST), fabricated using LPKF D104 milling machine, and measured using R&SZNA67 vector network analyzer. An excellent agreement is observed between the simulated and the measured results and a detailed comparison with the previous works is also presented. Due to attributes such as low-cost, easy to fabricate, and dual-band, it is believed that this system will find its application for future 5G systems.

This study provides an eight-component multiple-input multiple-output (MIMO) antenna architecture for fifth-generation (5G) mobile communication systems. The single antenna element is comprised of an L-shaped radiating component, an L-shaped parasitic element, and a ground plane with a rectangular slot. The main element with a slot-loaded ground plane helps to draw current from a coaxial feed from the other side of the board, while the parasitic element helps to elongate the current path and improve the impedance of the system. This enables the system to radiate at two different frequency ranges: 3.34–3.7 GHz and 4.67–5.08 GHz, with 360 MHz and 410 MHz bandwidths, respectively. For MIMO configuration, the radiating elements are designed on either side of a 0.8 mm thick FR-4 substrate, allowing space to accommodate a battery, radio frequency (RF) systems and subsystems, and camera and sensor modules. The corner and the middle elements are arranged in such a manner so that they can provide spatial and pattern diversity. Furthermore, at least 12 dB of isolation is established between any two radiating elements. Various MIMO performance parameters were evaluated, e.g., mean effective gain (MEG), channel capacity (CC), envelope correlation coefficient (ECC), realized gain, far-field characteristics, and efficiency. Single- and double-hand mode evaluations were performed to further demonstrate the capability of the proposed MIMO antenna. A prototype of the proposed MIMO antenna was manufactured and assessed to verify the simulated data. The measured and simulated results were found to be in good agreement. On the basis of its performance characteristics, the designed MIMO system could be used in 5G communication systems.