We study the generation and decay of aqueous foams stabilized by sodium dodecyl sulfate (SDS) in the presence of unmodified cellulose nanofibrils (CNF). Together with the rheology of aqueous suspensions containing CNF and SDS, the interfacial/colloidal interactions are determined by quartz crystal microgravimetry with dissipation monitoring, surface plasmon resonance, and isothermal titration calorimetry. The results are used to explain the properties of the air/water interface (interfacial activity and dilatational moduli determined from oscillating air bubbles) and of the bulk (steady-state flow, oscillatory shear, and capillary thinning). These properties are finally correlated to the foamability and to the foam stability. The latter was studied as a function of time by monitoring the foam volume, the liquid fraction, and the bubble size distribution. The shear-thinning effect of CNF is found to facilitate foam formation at SDS concentrations above the critical micelle concentration (c SDS ≥ cmc). Compared with foams stabilized by pure SDS, the presence of CNF enhances the viscosity and elasticity of the continuous phase as well as of the air/water interface. The CNF-containing foams have higher liquid fractions, larger initial bubble sizes, and better stability. Due to charge screening effects caused by sodium counter ions and depletion attraction caused by SDS micelles, especially at high SDS concentrations, CNF forms aggregates in the Plateau borders and nodes of the foam, thus slowing down liquid drainage and bubble growth and improving foam stability. Overall, our findings advance the understanding of the role of CNF in foam generation and stabilization.

No abstract

No abstract

No abstract

In our previous work we were able to prove that gelled bicontinuous microemulsions are a novel type of orthogonal self-assembled system. The study at hand aims at complementing our previous work by answering the question of whether gelled lyotropic liquid crystals are also orthogonal self-assembled systems. For this purpose we studied the same system, namely, water-n-decane/12-hydroxyoctadecanoic acid (12-HOA)-n-decyl tetraoxyethylene glycol ether (C10E4). The phase boundaries of the nongelled and the gelled lyotropic liquid crystals were determined visually and with (2)H NMR spectroscopy. Oscillating shear measurements revealed that the absolute values of the storage and loss moduli of the gelled liquid crystalline (LC) phases do not differ very much from those of the binary organogel. While both the phase behavior and the rheological properties of the LC phases support the hypothesis that gelled lyotropic liquid crystals are orthogonal self-assembled systems, freeze-fracture electron microscopy (FFEM) seems to indicate an influence of the gel network on the structure of the Lα phase and vice versa.

Does the presence of a gel network influence the properties of a lyotropic liquid crystal? Does the replacement of oil by a lyotropic liquid crystal influence the properties of an organogel? To answer these questions we study gelled lyotropic liquid crystals (LLC). In the present study we show that it is possible to gel the lamellar phase of the binary system water-didodecyl dimethylammonium bromide (2CDAB) with the organogelator 12-hydroxyoctadecanoic acid (12-HOA). We compare various properties of the gelled LLC phases with the "parent systems", i.e., with the binary organogel consisting of n-decane-12-HOA and with the nongelled LC phases, respectively. Optical and electron microscopy, differential scanning calorimetry (DSC), rheometry, as well as small and wide-angle X-ray scattering (SWAXS) proved the coexistence of an L phase and a 12-HOA gel network in the gelled L phase. However, a small influence of the L phase on the gel properties was seen, namely slightly lower sol-gel transition temperatures and viscoelastic moduli of the gelled L phase compared to the binary gel. On the other hand, the presence of the gel also has an influence on the L phase: the interlayer spacing of the surfactant bilayers in the gelled L phases is slightly larger compared to the nongelled L phases, which is due to mixing part of the 12-HOA molecules in the L bilayers. Despite this mutual influence the structures of both the L phase and the gel network are hardly disturbed in the gelled L phase, i.e., that the self-assembly of the surfactant and of the gelator molecules clearly occur in an orthogonal way.

The critical micelle concentration (cmc), the surface excess (Γ), as well as the micelle aggregation number (m) of the surfactant dodecyldimethylamine oxide (C12DMAO) have been reported to strongly depend on the pH-value of the aqueous surfactant solution. At high ionic strength, the cmc displays a minimum, while both Γ and m have a maximum at a pH-value close to the pKa of the surfactant. These experimental observations have been explained as being due to specific hydrogen bonds between the head groups, which are formed once the surfactant is partly or fully protonated. This investigation addresses the question of whether the pH also affects the foaming properties of C12DMAO solutions. To answer this question we measured the foamability and the foam stability of C12DMAO solutions at a fixed C12DMAO concentration of 5 cmc for five different pH-values, namely pH = 2, 3, 5, 8, and 10. We found that the foamability is hardly affected by the pH-value, while the foam stability strongly depends on the pH. As is the case for the above mentioned properties, the foam stability also displays an extremum in the studied pH-range, namely a maximum at pH = 5. We discuss our results in terms of the hydrogen bond hypothesis and show that this hypothesis indeed is in line with the observed trend for the foam stability. Moreover, we discuss that hydrogen bond formation may rationalize how the molecular structure of a surfactant affects foam stability.

This study relates to the release of non-cellulosic components (cell wall heteropolysaccharides, lignin, and extractives) from swollen wood fibers in the presence of an anionic surfactant (sodium dodecyl sulfate, SDS) at submicellar concentrations. Highly surface-active aggregates form between SDS and the leached, non-cellulosic components, which otherwise do not occur in the presence of cationic or nonionic surfactants. The in situ and efficient generation of liquid foams in the presence of the leached species is demonstrated. The foaming capacity and foam stability, as well as the foam’s structure, are determined as a function of the composition of the aqueous suspension. The results indicate that naturally occurring components bound to wood fibers are extractable solely with aqueous solutions of the anionic surfactant. Moreover, they can form surface-active aggregates that have a high foaming capacity. The results further our understanding of residual cell wall components and their role in the generation of foams.