Highly sensitive spectroscopic study of interfacial disorder and its correlation with the solvent additive and the molecular structure of the donor in bulk heterojunction organic solar cells.

This paper reports quantitative correlation of CH3NH3PbBr3 (MAPbBr3) thin film morphology to light emitting diode efficiency parameters. Sequential (spin coating) deposition is used for highly reproducible and dense film morphology of MAPbBr3 thin‐film. In this fabrication process using an orthogonal solvent approach, control of morphology, coverage, thickness, and optical properties in these compact thin‐films is demonstrated. Optical studies show direct correlation between morphology to dynamics of photoluminescence (PL) and absolute PL yield. Perovskite light emitting diodes (PeLEDs) are fabricated from these films to find the best ratio of PbBr2 versus MABr for optimal performance. This study demonstrates PeLEDs with high brightness, ≈1050 cd m−2 at 4.7 V (luminance efficiency ≈0.1 cd A−1), for optimal thin‐film process with state‐of‐the‐art device performance. This quantitative analysis suggests that these state‐of‐the‐art PeLEDs suffer from poor charge carrier balance (≈2%) and out‐coupling efficiency (≈6%). Interestingly, charge carrier balance and PL yield together can explain the change in PeLED efficiency modulation with film morphology. Studies on single carrier devices show that these PeLEDs are electron current dominated and charge carrier balance increases with operating bias voltage.

In this paper we correlate the solar cell performance with bimolecular packing of donor:acceptor bulk heterojunction (BHJ) organic solar cells (OSCs), where interchain ordering of the donor molecule and its influence on morphology, optical properties, and charge carrier dynamics of BHJ solar cells are studied in detail. Solar cells that are fabricated using more ordered defect free 100% regioregular poly(3-hexylthiophene) (DF-P3HT) as the donor polymer show ca. 10% increase in the average power conversion efficiency (PCE) when compared to that of the solar cell fabricated using 92% regioregularity P3HT, referred to as rr-P3HT. EQE and UV-vis absorption spectrum show a clear increase in the 607 nm vibronic shoulder of the DF-P3HT blend suggesting better interchain ordering which was also reflected in the less Urbach energy (Eu) value for this system. The increase in ordering inside the blend has enhanced the hole-mobility which is calculated from the single carrier device J-V characteristics. Electroluminance (EL) studies on the DF-P3HT system showed a red-shifted peak when compared to rr-P3HT-based devices suggesting low CT energy states in DF-P3HT. The morphologies of the blend films are studied using AFM and grazing-incidence wide-angle X-ray scattering (GIWAXS) suggesting increase in the roughness and phase segregation which could enhance the internal scattering of the light inside the device and improvement in the crystallinity along alkyl and π-stacking direction. Hence, higher PCE, lower Eu, red-shifted EL emission, high hole-mobility, and better crystallinity suggest improved interchain ordering has facilitated a more delocalized HOMO state in DF-P3HT-based BHJ solar cells.

Reducing the energy loss of sub-cells is critical for high performance tandem organic solar cells, while it is limited by the severe non-radiative voltage loss via the formation of non-emissive triplet excitons. Herein, we develop an ultra-narrow bandgap acceptor BTPSeV-4F through replacement of terminal thiophene by selenophene in the central fused ring of BTPSV-4F, for constructing efficient tandem organic solar cells. The selenophene substitution further decrease the optical bandgap of BTPSV-4F to 1.17 eV and suppress the formation of triplet exciton in the BTPSV-4F-based devices. The organic solar cells with BTPSeV-4F as acceptor demonstrate a higher power conversion efficiency of 14.2% with a record high short-circuit current density of 30.1 mA cm−2 and low energy loss of 0.55 eV benefitted from the low non-radiative energy loss due to the suppression of triplet exciton formation. We also develop a high-performance medium bandgap acceptor O1-Br for front cells. By integrating the PM6:O1-Br based front cells with the PTB7-Th:BTPSeV-4F based rear cells, the tandem organic solar cell demonstrates a power conversion efficiency of 19%. The results indicate that the suppression of triplet excitons formation in the near-infrared-absorbing acceptor by molecular design is an effective way to improve the photovoltaic performance of the tandem organic solar cells.