The importance of morphology to organic solar cell performance is well known, but to date, the lack of quantitative, nanoscale and statistical morphological information has hindered obtaining direct links to device function. Here resonant X‐ray scattering and microscopy are combined to quantitatively measure the nanoscale domain size, distribution and composition in high efficiency solar cells based on PTB7 and PC71BM. The results show that the solvent additive diiodooctane dramatically shrinks the domain size of pure fullerene agglomerates that are embedded in a polymer‐rich 70/30 wt.% molecularly mixed matrix, while preserving the domain composition relative to additive‐free devices. The fundamental miscibility between the species – measured to be equal to the device's matrix composition – is likely the dominant factor behind the overall morphology with the additive affecting the dispersion of excess fullerene. As even the molecular ordering measured by X‐ray diffraction is unchanged between the two processing routes the change in the distribution of domain size and therefore increased domain interface is primarily responsible for the dramatic increase in device performance. While fullerene exciton harvesting is clearly one significant cause of the increase owing to smaller domains, a measured increase in harvesting from the polymer species indicates that the molecular mixing is not the reason for the high efficiency in this system. Rather, excitations in the polymer likely require proximity to a pure fullerene phase for efficient charge separation and transport. Furthermore, in contrast to previous measurements on a PTB7‐based system, a hierarchical morphology was not observed, indicating that it is not necessary for high performance.

No abstract

The device function of polymer bulk heterojunction (BHJ) solar cells has been commonly interpreted to arise from charge separation at discrete interfaces between phase-separated materials and subsequent charge transport through these phases without consideration of phase purity. To probe composition, the miscibility of poly(3-hexylthiophene) (P3HT) and poly(2-methoxy-5-(3′,7′-dimethyloctyloxy)-1,4-phenylenevinylene) (MDMO-PPV) with phenyl-C61-butyric acid methyl ester (PCBM) has been determined, while the effects of polymer crystallinity on miscibility are probed using P3HT grades of varying regioregularity. It is found that, while no intercalation occurs in P3HT crystals, amorphous portions of P3HT and MDMO-PPV contain significant concentrations of PCBM, calling into question models based on pure phases and discrete interfaces. Furthermore, depth profiles of P3HT/PCBM bilayers reveal that even short annealing causes significant interdiffusion of both materials, showing that under no conditions do pure amorphous phases exist in BHJ or annealed bilayer devices. These results suggest that current models of charge separation and transport must be refined.

Band-like charge transport is observed in lead halide perovskite field-effect transistors.

No abstract

We present the development and characterization of a dedicated resonant soft x-ray scattering facility. Capable of operation over a wide energy range, the beamline and endstation are primarily used for scattering from soft matter systems around the carbon K-edge (∼285 eV). We describe the specialized design of the instrument and characteristics of the beamline. Operational characteristics of immediate interest to users such as polarization control, degree of higher harmonic spectral contamination, and detector noise are delineated. Of special interest is the development of a higher harmonic rejection system that improves the spectral purity of the x-ray beam. Special software and a user-friendly interface have been implemented to allow real-time data processing and preliminary data analysis simultaneous with data acquisition.

High-mobility semiconducting polymers offer the opportunity to develop flexible and large-area electronics for several applications, including wearable, portable and distributed sensors, monitoring and actuating devices. An enabler of this technology is a scalable printing process achieving uniform electrical performances over large area. As opposed to the deposition of highly crystalline films, orientational alignment of polymer chains, albeit commonly achieved by non-scalable/slow bulk alignment schemes, is a more robust approach towards large-area electronics. By combining pre-aggregating solvents for formulating the semiconductor and by adopting a room temperature wired bar-coating technique, here we demonstrate the fast deposition of submonolayers and nanostructured films of a model electron-transporting polymer. Our approach enables directional self-assembling of polymer chains exhibiting large transport anisotropy and a mobility up to 6.4 cm2 V−1 s−1, allowing very simple device architectures to operate at 3.3 MHz. Thus, the proposed deposition strategy is exceptionally promising for mass manufacturing of high-performance polymer circuits.

Domain purity and interface structure are known to be critical for fullerene‐based bulk heterojunction (BHJ) solar cells, yet have been very difficult to study. Using novel soft X‐ray tools, we delineate the importance of these parameters by comparing high performance cells based on a novel naphtha[1,2‐c:5,6‐c]bis[1,2,5]thiadiazole (NT) material to cells based on a 2,1,3‐benzothiadiazole (BT) analogue. BT‐based devices exhibit ∼15 nm, mixed domains that differ in composition by at most 22%, causing substantial bimolecular recombination. In contrast, NT‐based devices have more pure domains that are >80 nm in size, yet the polymer‐rich phase still contains at least 22% fullerene. Power conversion efficiency >6% is achieved for NT devices despite a domain size much larger than the nominal exciton diffusion length due to a favourable trade‐off in the mixed domain between exciton harvesting, charge transport, and bimolecular recombination. The miscibility of the fullerene with the NT and BT polymer is measured and correlated to the purity in devices. Importantly, polarized x‐ray scattering reveals preferential face‐on orientation of the NT polymer relative to the PCBM‐rich domains. Such ordering has previously not been observed in fullerene‐based solar cells and is shown here to be possibly a controlling or contributing factor to high performance.