No abstract

Titania-loaded coal char catalyst was successfully prepared. The preparation steps involved pyrolysis of low rank coal at different temperatures and durations, sulfonation, impregnation of titanium(IV) isopropoxide, and then heating at 110 °C. It is found that the coal chars’ surfaces were rough after sulfonation and impregnation, while large pore volume, high surface area and carbon composition were observed at low pyrolysis temperature for short duration. These properties contributed to high selectivity towards benzaldehyde (> 90 %) at 600 °C (0.5–2 h)) in styrene oxidation using aqueous hydrogen peroxide as the oxidant.

The evaluation of kinetic adsorption process of sulfonated carbon-derived from Eichhornia crassipes in the adsorption of methylene blue dye from aqueous solution has been carried out. The sulfonated carbon-derived from E. crassipes (EGS-600) was prepared by carbonation of E. crassipes powder at 600 °C for 1 h, followed by sulfonation with concentrated sulfuric acid for 3 h. The physical properties of the adsorbents were characterized by using Fourier transform infrared spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and nitrogen adsorption-desorption studies. Adsorption study using methylene blue dye was carried out by varying the contact time and initial dye concentration for investigated kinetics adsorption models. The effect of varying temperature was used to determine the thermodynamic parameter value of ΔG, ΔH, and ΔS. The results showed that the equilibrium adsorption capacity was 98% when EGS-600 is used as an adsorbent. The methylene blue dye adsorption onto adsorbent takes place spontaneity and follows a pseudo-second-order adsorption kinetic model.

No abstract

<p>The modified coal char from low-rank coal by sulfonation, titanium impregnation and followed by alkyl silylation possesses high catalytic activity in styrene oxidation. The surface of coal char was undergone several steps as such: modification using concentrated sulfuric acid in the sulfonation process, impregnation of 500 mmol titanium(IV) isopropoxide and followed by alkyl silylation of n-octadecyltriclorosilane (OTS). The catalysts were characterized by X-ray diffraction (XRD), IR spectroscopy, nitrogen adsorption, and hydrophobicity. The catalytic activity of the catalysts has been examined in the liquid phase styrene oxidation by using aqueous hydrogen peroxide as oxidant. The catalytic study showed the alkyl silylation could enhance the catalytic activity of Ti-SO₃H/CC-600(2.0). High catalytic activity and reusability of the o-Ti-SO₃H/CC-600(2.0) were related to the modification of local environment of titanium active sites and the enhancement the hydrophobicity of catalyst particle by alkyl silylation. Copyright © 2017 BCREC GROUP. All rights reserved</p><p><em>Received: 24^th May 2016; Revised: 11^st October 2016; Accepted: 18^th October 2016</em></p><p><strong>How to Cite:</strong> Nurhadi, M. (2017). Modification of Coal Char-loaded TiO₂ by Sulfonation and Alkylsilylation to Enhance Catalytic Activity in Styrene Oxidation with Hydrogen Peroxide as Oxidant. <em>Bulletin of Chemical Reaction Engineering &amp; Catalysis</em>, 12 (1): 55-61 (doi:10.9767/bcrec.12.1.501.55-61)</p><p><strong>Permalink/DOI</strong>: http://dx.doi.org/10.9767/bcrec.12.1.501.55-61</p><p> </p>

The carbon-containing hydroxyapatite has been synthesized using the fish bone obtained from East Kalimantan, Indonesia. The synthesis was conducted at varying calcination temperature (300-700 °C) and duration time (1-5 h). The carbon-containing hydroxyapatite were characterized by using Nitrogen adsorption-desorption, Fourier transform infrared spectroscopy, X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Thermogravimetric analysis (TGA) and Differential thermal analysis (DTA). The carbon-containing hydroxyapatite nanoparticles consisted of the mesoporous structure with a specific surface area of 159 m2.g-1 and pore size of 44 Å. The carbon-containing hydroxyapatite nanoparticles were utilized as the adsorbent for the removal of methylene blue by varying the contact time, initial dye concentration, pH, adsorbent dosage and temperature. The maximum amount of adsorption capacity was 56.49 mg.g-1. The adsorption was well fitted with the Langmuir adsorption model (R2 ~ 0.998) and the pseudo-second-order model. This indicated that the dye molecules were adsorbed on the surface-active site of carbon-containing hydroxyapatite via chemical binding, forming an adsorbate monolayer. Hence, the adsorption capability corresponds to the physical properties such as the surface area and pore volume of hydroxyapatite because the larger surface area consists of higher binding sites for the adsorption. Thermodynamic parameters, including the Gibbs free energy (ΔG), enthalpy (ΔH), and entropy (ΔS), indicated that the adsorption of methylene blue onto the carbon-containing hydroxyapatite nanoparticles was spontaneous. Thus, carbon-containing hydroxyapatite nanoparticles can be applied as a low-cost adsorbent for the treatment of industrial effluents that are contaminated with the methylene blue. Copyright © 2019 BCREC Group. All rights reserved

The study of TiO2-sulfonated carbon-derived from Eichhornia crassipes (TiO2/SCEC), as an effective adsorbent to remove Methylene blue (MB) and Congo red (CR) dyes from aqueous solution, has been conducted. The preparation steps of TiO2/SCEC adsorbent involved the carbonisation of E. crassipes powder at 600 °C for 1 h, followed by sulfonation of carbon for 3 h and impregnation through titanium(IV) isopropoxide (500 µmol). The physical properties of the adsorbents were characterized by using X-ray fluorescence (XRF), Fourier transform infrared, X-ray diffraction (XRD), Scanning electron microscopy with Energy dispersive X-ray (SEM-EDX), Thermogravimetric analysis (TGA) and nitrogen adsorption-desorption studies. The dye removal study using TiO2/SCEC adsorbent was carried out by varying of contact time, adsorbent dosage, initial dye concentration, pH, particles size of adsorbent and temperature. The kinetics models were determined by the effects of contact time and the thermodynamic parameters (ΔH, ΔS, and ΔG), which were calculated by the effects of temperature. The results showed that the maximum dye removal capacity of TiO2/SCEC were 18.8 mg.g-1 for MB and 36.5 mg.g-1 for CR. The removal of MB and CR dyes using TiO2/SCEC adsorbent performed a pseudo-second order kinetic models with spontaneity. Copyright © 2020 BCREC Group. All rights reserved

No abstract