This work introduces an additive direct-write nanofabrication technique for producing extremely conductive gold nanostructures from a commercial metalorganic precursor. Gold content of 91 atomic % (at. %) was achieved by using water as an oxidative enhancer during direct-write deposition. A model was developed based on the deposition rate and the chemical composition, and it explains the surface processes that lead to the increases in gold purity and deposition yield. Co-injection of an oxidative enhancer enabled Focused Electron Beam Induced Deposition (FEBID)—a maskless, resistless deposition method for three dimensional (3D) nanostructures—to directly yield pure gold in a single process step, without post-deposition purification. Gold nanowires displayed resistivity down to 8.8 μΩ cm. This is the highest conductivity achieved so far from FEBID and it opens the possibility of applications in nanoelectronics, such as direct-write contacts to nanomaterials. The increased gold deposition yield and the ultralow carbon level will facilitate future applications such as the fabrication of 3D nanostructures in nanoplasmonics and biomolecule immobilization.
Nanomagnet logic (NML) is a relatively new computation technology that uses arrays of shape-controlled nanomagnets to enable digital processing. Currently, conventional resist-based lithographic processes limit the design of NML circuitry to planar nanostructures with homogeneous thicknesses. Here, we demonstrate the focused electron beam induced deposition of Fe-based nanomaterial for magnetic in-plane nanowires and out-of-plane nanopillars. Three-dimensional (3D) NML was achieved based on the magnetic coupling between nanowires and nanopillars in a 3D array. Additionally, the same Fe-based nanomaterial was used to produce tilt-corrected high-aspect-ratio probes for the accurate magnetic force microscopy (MFM) analysis of the fabricated 3D NML gate arrays. The interpretation of the MFM measurements was supported by magnetic simulations using the Object Oriented MicroMagnetic Framework. Introducing vertical out-of-plane nanopillars not only increases the packing density of 3D NML but also introduces an extra magnetic degree of freedom, offering a new approach to input/output and processing functionalities in nanomagnetic computing.
Three-dimensional gold (Au) nanostructures offer promise in nanoplasmonics, biomedical applications, electrochemical sensing and as contacts for carbon-based electronics. Direct-write techniques such as focused-electron-beam-induced deposition (FEBID) can provide such precisely patterned nanostructures. Unfortunately, FEBID Au traditionally suffers from a high nonmetallic content and cannot meet the purity requirements for these applications. Here we report exceptionally pure pristine FEBID Au nanostructures comprising submicrometer-large monocrystalline Au sections. On the basis of high-resolution transmission electron microscopy results and Monte Carlo simulations of electron trajectories in the deposited nanostructures, we propose a curing mechanism that elucidates the observed phenomena. The in situ focused-electron-beam-induced curing mechanism was supported by postdeposition ex situ curing and, in combination with oxygen plasma cleaning, is utilized as a straightforward purification method for planar FEBID structures. This work paves the way for the application of FEBID Au nanostructures in a new generation of biosensors and plasmonic nanodevices.
The capability to control matter down to the nanoscale level in combination with the novel magnetic properties of nanomaterials have attracted increasing attention in the last few decades due to their applications in magnetic sensing, hard disc data storage and logic devices. Therefore, many efforts have been devoted to the implementation of both nanofabrication methods as well as characterization of magnetic nanoelements. In this study, Fe‐based nanostructures have been synthesized on Si(100) by focused electron beam induced deposition (FEBID) utilizing iron pentacarbonyl as precursor. The so obtained nanostructures exhibit a remarkably high iron content (Fe > 80 at.%), expected to give rise to a ferromagnetic behaviour. For that reason, magnetic force microscopy (MFM) analyses were performed on the obtained FEBID Fe nanostructures. Moreover, object oriented micromagnetic framework (OOMMF) magnetic simulations have been executed to study the influence of the geometry on the magnetic properties of iron single‐domain nanowires. FEBID is a mask‐less nanofabrication method based on the injection of precursor gas molecules in proximity of the deposition area where their decomposition is locally induced by a focused electron beam.
Magnetic materials synthesized on the nanometer-scale level are essential for several applications, such as spintronics and magnetologic. As a successful nanofabrication approach, focused electron beam-induced deposition (FEBID) stands out as a direct-write technique. FEBID uses an electron beam to locally induce a CVD process, avoiding the use of masks and resists. In this work, Fe-based nanostructures are synthesized on Si(100) by FEBID, starting from iron pentacarbonyl. A systematic variation of FEBID parameters is performed, to study their influence on the geometry and composition of the deposit. Based on the results, specific deposition conditions are suggested for magneto-logic applications and fabrication of large structures.
This work presents a highly effective approach for the chemical purification of directly written 2D and 3D gold nanostructures suitable for plasmonics, biomolecule immobilisation, and nanoelectronics. Gold nano- and microstructures can be fabricated by one-step direct-write lithography process using focused electron beam induced deposition (FEBID). Typically, as-deposited gold nanostructures suffer from a low Au content and unacceptably high carbon contamination. We show that the undesirable carbon contamination can be diminished using a two-step process – a combination of optimized deposition followed by appropriate postdeposition cleaning. Starting from the common metal-organic precursor Me2-Au-tfac, it is demonstrated that the Au content in pristine FEBID nanostructures can be increased from 30 atom % to as much as 72 atom %, depending on the sustained electron beam dose. As a second step, oxygen-plasma treatment is established to further enhance the Au content in the structures, while preserving their morphology to a high degree. This two-step process represents a simple, feasible and high-throughput method for direct writing of purer gold nanostructures that can enable their future use for demanding applications.
Among various multi-metal combinations, Au-Fe nanoalloys are envisaged as prospective materials for data storage applications. Here we report on the first successful achievement of Au-Fe nanoalloys using focused electron beam-induced deposition (FEBID), exploiting the possibility of directly writing nanostructures at nanometer resolution. Gaseous organometallic precursors are injected simultaneously into the deposition chamber to co-deposit Fe and Au within the same nanostructure. Fabricated nanostructures show a spatially uniform elemental ratio of iron to gold that can be tailored by experimental conditions.
Focused electron beam induced deposition (FEBID) is a novel direct‐writing technique to produce noble metal nanostructures. In this work, FEBID has been employed for the first time to fabricate metal‐oxide‐semiconductor capacitors (MOSCAPs). Experimental parameters such as precursor temperature, substrate temperature and the (de)focus of the electron beam have been optimized to deposit electrode structures of a relatively large area within a short timeframe. Using FEBID, gold electrodes have been deposited on top of an atomic layer deposited (ALD) dielectric aluminum oxide layer. Chemical composition of the produced structures has been studied using energy dispersive X‐ray spectroscopy (EDX). Current–voltage (I–V) measurements have confirmed the conductivity of FEBID gold nanowires (NWs). Measured capacitance–voltage (C–V) characteristics of FEBID‐fabricated MOSCAP prototypes resemble the typical C–V characteristics of conventionally fabricated MOSCAPs, thus confirming the functionality of our FEBID devices. Illustration of a MOS capacitor fabricated by FEBID.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.