The development of antimicrobial packaging has been growing rapidly due to an increase in awareness and demands for sustainable active packaging that could preserve the quality and prolong the shelf life of foods and products. The addition of highly efficient antibacterial nanoparticles, antifungals, and antioxidants to biodegradable and environmentally friendly green polymers has become a significant advancement trend for the packaging evolution. Impregnation of antimicrobial agents into the packaging film is essential for impeding or destroying the pathogenic microorganisms causing food illness and deterioration. Higher safety and quality as well as an extended shelf life of sustainable active packaging desired by the industry are further enhanced by applying the different types of antimicrobial packaging systems. Antimicrobial packaging not only can offer a wide range of advantages, but also preserves the environment through usage of renewable and biodegradable polymers instead of common synthetic polymers, thus reducing plastic pollution generated by humankind. This review intended to provide a summary of current trends and applications of antimicrobial, biodegradable films in the packaging industry as well as the innovation of nanotechnology to increase efficiency of novel, bio-based packaging systems.

The depletion of petroleum-based resources and the adverse environmental problems, such as pollution, have stimulated considerable interest in the development of environmentally sustainable materials, which are composed of natural fiber–reinforced polymer composites. These materials could be tailored for a broad range of sustainable industrial applications with new surface functionalities. However, there are several challenges and drawbacks, such as composites processing production and fiber/matrix adhesion, that need to be addressed and overcome. This review could provide an overview of the technological challenges, processing techniques, characterization, properties, and potential applications of NFRPC for sustainable industrial applications. Interestingly, a roadmap for NFRPC to move into Industry 4.0 was highlighted in this review.

Higher content of silica in geopolymer coating resulted in better thermal properties. Since rice husk ash (RHA) has the highest silica content compared to other aluminosilicate sources available, it offers the best potential to be an alternative silica source in producing geopolymer coating binder. In this study, five factors including ratio of alkaline activator (AA) (A), ratio of RHA/AA (B), curing temperature (C), curing time (D) and concentration of NaOH (E) were analyzed using statistical analysis to identify the significant factors that mostly influence fire retardant performance of RHA-based geopolymer coating. The fire retardant tests were conducted and results recorded included (i) time taken to reach 300°C and (ii) temperature at equilibrium. Sample S7 (coating composition of A=5.5, B=0.3, C=50°C, D=7days, E=8M) which produced the best fire retardant performance was selected for further detailed investigation using thermogravimetry analysis (TGA) and scanning electron microscopy (SEM). It was found that the back temperature of mild steel plate of sample S7 reached 300°C after 17 minutes and achieved an equilibrium state at 398°C. SEM micrographs showed the presence of needle-like structures formed after fire test might be the reason for the best fire performance of sample S7.

According to the Food Wastage Footprint and Climate Change Report, about 15% of all fruits and 25% of all vegetables are wasted at the base of the food production chain. The significant losses and wastes in the fresh and processing industries is becoming a serious environmental issue, mainly due to the microbial degradation impacts. There has been a recent surge in research and innovation related to food, packaging, and pharmaceutical applications to address these problems. The underutilized wastes (seed, skin, rind, and pomace) potentially present good sources of valuable bioactive compounds, including functional nutrients, amylopectin, phytochemicals, vitamins, enzymes, dietary fibers, and oils. Fruit and vegetable wastes (FVW) are rich in nutrients and extra nutritional compounds that contribute to the development of animal feed, bioactive ingredients, and ethanol production. In the development of active packaging films, pectin and other biopolymers are commonly used. In addition, the most recent research studies dealing with FVW have enhanced the physical, mechanical, antioxidant, and antimicrobial properties of packaging and biocomposite systems. Innovative technologies that can be used for sensitive bioactive compound extraction and fortification will be crucial in valorizing FVW completely; thus, this article aims to report the progress made in terms of the valorization of FVW and to emphasize the applications of FVW in active packaging and biocomposites, their by-products, and the innovative technologies (both thermal and non-thermal) that can be used for bioactive compounds extraction.

Food packaging has seen a growth in the use of materials derived from renewable resources such as poly(lactic acid) (PLA). However, the initial costs to produce bioplastics are typically high. Tropical fruit waste as naturally sourced fibres, such as jackfruit skin, can be used as a cost-reducing filler for PLA. The main objective in this study is to fabricate a low-cost natural fibre-reinforced polymer that potentially applies in packaging with the aid of bleaching treatment. The treatment shows a rougher surface fibre in Scanning electron microscopy (SEM) micrographs and it is expected to have better mechanical locking with the matrix, and this is found similar with a Fourier-transform infrared spectroscopy (FTIR) analysis. Unfortunately, fibre insertion does find low tensile performances, yet bleached-fibre composites improved its performance significantly. A similar situation was found in the thermal characterization where a low-thermal stability natural fibre composite has lower thermal behaviour and this increased with bleaching treatment. Besides, bleached-fibre composites have a longer service period. Besides, a 15 wt% thymol insertion inhibits the growth of Gram-positive bacteria in the composites and the non-treated fibre composite has better thymol effects. The 30 wt% of the bleached-fibre insertion composite has a high potential to reduce the cost of bioplastic products with minimum alterations of overall performances.

Fresh guava juice was clarified using ultrafiltration (UF) process on a laboratory scale in this study. The observation was undertaken to determine the effect of the operating pressure (OP) on the permeate flux (J) behaviour, the fouling mechanisms as well as the quality attributes of the guava juice i.e. pH, turbidity, colour, total soluble solids (TSS), total phenolic content (TPC) and ascorbic acid content (AAC). The clarification of guava juice was performed in a batch mode using a 100 kDa polymeric membrane in a dead-end module at an operating pressure OP of 1.0, 1.5, 2.0 and 2.5 bar. The results showed that a high OP resulted in high flux during the UF process. The flux-pressure curves exhibited no increase for an OP higher than 2.0 bar (Plim), with a limiting flux (Jlim) identified at 17.22 kg/m2 /hr. Intermediate and total pore-blocking has been identified as the major fouling mechanisms in the process. The resulting juice after filtration showed a reduction of more than 97% turbidity with a lower TSS by 7 to 17%, compared to the fresh juice. The UF process permitted a good level of clarification with improvement in colour properties with a stable pH at 3.8. However, a 19 to 27% and 18 to 22% reduction of TPC and AAC, respectively were found in the filtered juice with respect to the fresh juice. For appropriate flux behaviour and juice quality attributes, the process UF should be conducted at 2.0 bar.

Geopolymer coating using rice husk ash (RHA) as the aluminosilicate source has shown excellent fire retardant properties. However, incorporation of rice husk ash into the geopolymer matrix increased water absorption properties of the polymer composite. As such, silicone rubber (SiR) was introduced to improve the moisture absorption and fire retardant properties of the composite. Additionally, the less efficient one-factor-at-a-time (OFAT) approach was conventionally used in past studies on the RHA-based geopolymer composite. In understanding the optimum value and significant effect of factors on the fire retardant and moisture absorption properties of the binary blended geopolymer coating composite, the use of statistical analysis and regression coefficient model (mathematical model) was considered essential. The objectives of this study are to identify the significant effect of factors on moisture absorption and fire retardant properties, to determine the optimum composition, and to study the microstructure of the rice husk ash/silicone rubber (RHA/SiR)-based binary blended geopolymer coating composite. The RHA/AA and SiR/Ge ratios were chosen as factors, and the response surface methodology (RSM) was employed to design experiments and conduct analyses. Fire retardant and moisture absorption tests were conducted. A scanning electron microscope (SEM) was used to observe the microstructure of geopolymer samples. The RHA/alkaline activator (AA) and SiR/Ge ratios were shown to have a significant effect on the responses (temperature at equilibrium and moisture absorption). The high ratio of RHA/AA and SiR/Ge resulted in a lower temperature at equilibrium (TAE) below 200°C and at moisture absorption below 16%. The optimum formulation for the geopolymer coating composite can be achieved when the RHA/AA ratio, SiR/Ge ratio, and sodium hydroxide concentration are set at 0.85, 0.70, and 14 M, respectively. SEM micrographs of samples with good fire retardant properties showed that the char residue of the geopolymer composite coating, which is a layer of excess silicone rubber, is porous and continuous, thus providing a shielding effect for the layer of geopolymer underneath. The sample with good moisture absorption showed the formation of a thin outer layer of silicone rubber without any cracks. The unreacted SiR formed a thin layer beneath the geopolymer composite matrix providing a good moisture barrier.

No abstract