Recent advances in flexible and stretchable electronics (FSE), a technology diverging from the conventional rigid silicon technology, have stimulated fundamental scientific and technological research efforts. FSE aims at enabling disruptive applications such as flexible displays, wearable sensors, printed RFID tags on packaging, electronics on skin/organs, and Internet-of-things as well as possibly reducing the cost of electronic device fabrication. Thus, the key materials components of electronics, the semiconductor, the dielectric, and the conductor as well as the passive (substrate, planarization, passivation, and encapsulation layers) must exhibit electrical performance and mechanical properties compatible with FSE components and products. In this review, we summarize and analyze recent advances in materials concepts as well as in thin-film fabrication techniques for high- k (or high-capacitance) gate dielectrics when integrated with FSE-compatible semiconductors such as organics, metal oxides, quantum dot arrays, carbon nanotubes, graphene, and other 2D semiconductors. Since thin-film transistors (TFTs) are the key enablers of FSE devices, we discuss TFT structures and operation mechanisms after a discussion on the needs and general requirements of gate dielectrics. Also, the advantages of high- k dielectrics over low- k ones in TFT applications were elaborated. Next, after presenting the design and properties of high- k polymers and inorganic, electrolyte, and hybrid dielectric families, we focus on the most important fabrication methodologies for their deposition as TFT gate dielectric thin films. Furthermore, we provide a detailed summary of recent progress in performance of FSE TFTs based on these high- k dielectrics, focusing primarily on emerging semiconductor types. Finally, we conclude with an outlook and challenges section.

Singlet exciton fission is a spin-allowed process to generate two triplet excitons from a single absorbed photon. This phenomenon offers great potential in organic photovoltaics, but the mechanism remains poorly understood. Most reports to date have addressed intermolecular fission within small-molecular crystals. However, through appropriate chemical design chromophores capable of intramolecular fission can also be produced. Here we directly observe sub-100 fs activated singlet fission in a semiconducting poly(thienylenevinylene). We demonstrate that fission proceeds directly from the initial 1Bu exciton, contrary to current models that involve the lower-lying 2Ag exciton. In solution, the generated triplet pairs rapidly recombine and decay through the 2Ag state. In films, exciton diffusion breaks this symmetry and we observe long-lived triplets which form charge-transfer states in photovoltaic blends.

The improvement of the power conversion efficiency (PCE) of polymer bulk heterojunction (BHJ) solar cells has generally been achieved through synthetic design to control frontier molecular orbital energies and molecular ordering of the electron-donating polymer. An alternate approach to control the PCE of a BHJ is to tune the miscibility of the fullerene and a semiconducting polymer by varying the structure of the fullerene. The miscibility of a series of 1,4-fullerene adducts in the semiconducting polymer, poly(3-hexylselenophene), P3HS, was measured by dynamic secondary ion mass spectrometry using a model bilayer structure. The microstructure of the bilayer was investigated using high-angle annular dark-field scanning transmission microscopy and linked to the polymer-fullerene miscibility. Finally, P3HS:fullerene BHJ solar cells were fabricated from each fullerene derivative, enabling the correlation of the active layer microstructure to the charge collection efficiency and resulting PCE of each system. The volume fraction of polymer-rich, fullerene-rich, and polymer-fullerene mixed domains can be tuned using the miscibility leading to improvement in the charge collection efficiency and PCE in P3HS:fullerene BHJ solar cells. These results suggest a rational approach to the design of fullerenes for improved BHJ solar cells.

Syntheses, properties and applications of fully conjugated ladder polymers are reviewed, together with an outlook to future opportunities and challenges.

Data-driven approaches have brought about a revolution in manufacturing; however, challenges persist in their applications to synthetic strategies.

Hybrid composites of semiconducting polymers and metal oxides are promising combinations for solar cells. However, forming a well-controlled nanostructure with bicontinuous interpenetrating networks throughout the photoactive film is difficult to achieve. Pre-structured ''mesoporous'' metal oxide electrodes can act as a well-defined template for latter polymer infiltration. However, the long range infiltration of polymer chains into contorted porous channels has appeared to elude the scientific community, limiting the advancement of this technology. Here we present a structural and electronic characterisation of poly(3-hexylthiophene) (P3HT) infiltrated into mesoporous dye-sensitized TiO 2 . Through a combination of techniques we achieve uniform pore filling of P3HT up to depths of over 4 mm, but the volumetric fraction of the pores filled with polymer is less than 24%. Despite this low pore-filling, exceptionally efficient charge collection is demonstrated, illustrating that pore filling is not the critical issue for mesoporous hybrid solar cells.

We study the molecular order and morphology in poly(3-hexylthiophene) (P3HT) and poly(3-hexylselenophene) (P3HS) thin films and their blends with [6,6]-phenyl-C(61)-butyric acid methyl ester (PCBM). We find that substitution of the sulfur atoms in the thiophene rings of P3HT by heavy selenium atoms increases the tendency of the molecules to form better ordered phase; interestingly, their overall fraction of ordered phase is much lower than that of P3HT-based films. The higher tendency of P3HS molecules to order (aggregate) is consistent with more planar chain conformation simulated. The lower fraction of ordered phase (or the higher fraction of disordered phase) in P3HS-based films is clearly identified by in-plane skeleton Raman modes under resonant excitation conditions, such as a smaller ratio of the C═C modes associated with the ordered (∼1422 cm(-1)) and disordered (∼1446 cm(-1)) phases (I(1422 cm(-1))/I(1446 cm(-1)) = 1.4 for P3HS and 0.6 for P3HS:PCBM), compared with P3HT-based films (I(1449 cm(-1))/I(1470 cm(-1)) = 2.5 for P3HT and 1.0 for P3HT:PCBM) and a larger Raman dispersion of the C═C mode: P3HS (17 cm(-1)) versus P3HT (6 cm(-1)) and P3HS:PCBM (36 cm(-1)) versus P3HT:PCBM films (23 cm(-1)). The higher fraction of disordered phase in P3HS prevents the formation of micrometer-sized PCBM aggregates in blend films during thermal annealing. Importantly, this lower fraction but better quality of ordered phase in P3HS molecules strongly influences P3HS:PCBM photovoltaic performance, producing smaller short-circuit current (J(sc)) in pristine devices, but significantly larger increase in J(sc) after annealing compared to P3HT:PCBM devices. Our results clarify the effects of heavy atom substitution in low band gap polymers and their impact on blend morphology and device performance. Furthermore, our study clearly demonstrates resonant Raman spectroscopy as a simple, but powerful, structural probe which provides important information about "fraction/quantity of ordered phase" of molecules, not easily accessible using traditional X-ray-based techniques.

Ring opening metathesis polymerization (ROMP) of a series of low-strain cyclic olefins and their hydroxyl derivatives using second generation Hoveyda-Grubbs catalyst has been investigated. Additionally, density functional theory (DFT) calculations were performed to evaluate the ring strain energies of the cyclic olefins and their hydroxyl derivatives, coupled with kinetic studies for the ROMP reactions. It was found that among different ring size monomers, Cy8 having a relatively moderate ring strain energy in comparison with the other cyclic olefins, exhibited the highest monomer conversion. The effect of temperature (0, 10, 15, and 25 8C) and monomer concentration (1 M; 2.5 M and 5 M for Cy5; and 1 M and 5 M for Cy7) for the cyclic olefins Cy5 and Cy7 were investigated. In general, the experimental results for the kinetic ROMP studies obtained using complex HG2 correlate really well with the DFT calculations determined for the ring strain energies of the cyclic olefins. For comparison, DFT calculations predicted the following trend for the ring strain energies Cy8 > Cy5 > Cy7 > Cy6, and the polymerizations carried out experimentally followed the same trend in terms of monomer conversion, with the exception of Cy5 and Cy7 at lower concentrations, which followed this trend Cy8 > Cy7 > Cy5 > Cy6.