As a stacked form of ultrathin polymer films, multilayer nanostructures are of great interest in various applications. Coarse-grained molecular dynamics simulations were carried out to understand the behaviors of interfacial diffusion and bonding of multilayer polymer films. We found two obvious stages for the interfacial diffusion of polymers in the multilayer film, and it is 3 times faster in the first stage than in the second one due to the evolution of molecular conformations. The polymers near the interfaces have an in-plane mobility much higher than the out-of-plane one. The strength of interfacial bonding has been characterized by the fast tensile stress-strain curve along the normal direction. It shows multiple yielding points for the multilayer polymer films, which is distinct from the tensile behavior of the bulk. The ultimate tensile stress (UTS) and corresponding separating strain, surprisingly, do not necessarily increase with diffusion time. Because of the dramatic molecular rotation and extension during the first stage of interfacial diffusion, the interlayer interpenetration is nonuniformly distributed in the plane of the interface. Such a nonuniform distribution may be one of the reasons for the decrease of the UTS and separating strain.

No abstract

Steam generation through efficient utilization of solar energy is a promising technology in addressing the challenge of global freshwater shortage and water pollution. One of the biggest hurdles for traditional photothermal membranes to function continuously in a high temperature, high salt, and corrosive environment has been attributed to their rapid decline of mechanical properties. In this work, a highly efficient solar-driven interfacial water evaporation system has been developed via a polydopamine/carbon/silicon (PCS) composite membrane supported by a floating insulation foam substrate. A 3.1 fold increase in the water vaporization rate was recorded compared with the pure water system. The 2D-carbon nanolayer on the surface was successfully prepared by carbonizing low-cost linear polyethylene with a glass fiber (GF) membrane as the substrate, and then the carbon membrane was modified with dopamine to control water transport on the carbon coating and within the glass fiber. The PCS membrane has a high efficiency for solar steam generation owing to high optical absorption and has excellent solar thermal conversion capability. The evaporation rate and solar thermal conversion efficiency of the PCS membrane under simulated sunlight irradiation with 1 sun (1 kW·m–2) are 1.39 kg·m–2·h–1 and 80.4% respectively, which are significantly higher compared to GF membrane, carbon/silicon (CS) membrane, and pure water without a photothermal membrane. The water evaporation system retained high efficiency after 20 cycles under simulated sunlight irradiation of 1 sun. This study provides critical insight on the design and fabrication of a highly efficient and durable evaporation system.

No abstract

In this work, expandable graphite (EG)/thermoplastic polyurethane (TPU) composites with excellent exfoliation, dispersion and two-dimensional plane orientation of the EG fillers were manufactured by microlayer coextrusion technology.

As one of the duplicated cases of ultrathin polymer films, multilayer graphite/polymer composites are of great interests in various applications. Graphite/polyethylene (PE) composites with various layer numbers and graphite particle sizes were prepared by lamination. The mechanical and dielectric properties and crystalline behavior of the composites were investigated by scanning electron microscopy, differential scanning calorimetry, tensile test, and dielectric strength test. With the same amount of graphite addition, the tensile strength of the composites increases with decreasing layer thickness, but decreases with increasing graphite particle size. The longitudinal tensile strength is greater than the transverse one. The tensile strength of the 3 6 -layer composites with a particle size of 15 μm has enhancements of 34.76 and 68.39% in the longitudinal and transverse directions compared with that of the single-layer pure PE film. The dielectric constant of the composites nonlinearly increases with decreasing layer thickness, while the dielectric loss is independent of this factor. The dielectric constant of the 3 6 -layer composites with a particle size of 15 μm is about two times as large as that of the single-layer pure PE film. The crystalline peak temperature and the crystallinity of the composites increase with the decrease in layer thickness. Coarsegrained molecular dynamics simulations were also carried out to understand the experimental observations by getting an insight into the microstructure of the multilayer composites. This work would be helpful for the production of optimized of multilayer graphite/polymer composites by lamination for electric energy storage.

In this paper, ammonium polyphosphate(APP)/expandable graphite(EG)/thermoplastic polyurethane (TPU) composites were prepared by microlayer coextrusion technology, APP and EG fillers had good synergistic flame retardancy and excellent dispersion in TPU matrix, which greatly improved the flame retardancy and mechanical properties of multilayer composites. The dispersion of APP and EG in TPU was characterized by using SEM, the flame retardancy of composites was characterized by using UL94 and LOI, the thermal stability of composites was characterized by using TGA and DTG, and tensile test was used to characterized the mechanical properties of composites. SEM showed that the microlayer coextrusion technology significantly improved the dispersion of APP and EG in TPU. As showed by the experimental results, the vertical combustion level of ordinary blended composites reached V‐2 after adding only one kind of filler either APP or EG, and the vertical combustion level of ordinary blended composites reached V‐0 with APP and EG applied together, while the vertical combustion level of microlayer coextruded composites all reached V‐0 when the total addition of APP and EG was 15%. In particular, the LOI value of microlayer coextruded composites was 30.9%, while the LOI value of ordinary blended composites only was 27.9% when APP: EG = 1: 1. At this time, the flame retardancy level of APP/EG/TPU composites was the best. In addition, the thermal stability and mechanical properties of microlayer coextruded composites were far superior to ordinary blended composites. In conclusion, the synergistic flame retardancy of APP and EG fillers and the dispersion of APP and EG fillers in TPU matrix played a significant role in enhancing flame retardancy and mechanical properties.

No abstract