A new environmentally friendly method of photoreactive pressure-sensitive adhesives (PSAs) preparation was demonstrated. PSAs based on n-butyl acrylate (BA), acrylic acid (AA) and 4-acryloyloxy benxophenone (ABP) were prepared via the UV-induced cotelomerization process in the presence of a radical photoinitiator (acylphosphine oxide) and telogen (tetrabromomethane). Hydroxyterminated polybutadiene was used as a crosslinking agent. Influence of AA concentration (0–10 wt %) on kinetics of the cotelomerization process was investigated using a photodifferential scanning calorimetry method, selected physicochemical features of obtained photoreactive BA/AA/ABP cotelomers (molecular masses, polydispersity, monomers conversion and dynamic viscosity) and self-adhesive properties of obtained PSAs (adhesion, tack and cohesion) were studied, as well. It turned out that AA content is the important factor that influences monomers conversion (thereby the volatile parts content in prepolymer) and PSAs’ properties. As the acrylic acid content increases, the reaction rate increases, but the total monomers conversion and the solid content of the prepolymer decreases. Additionally, the adhesion and cohesion of PSAs were grown up, and their tackiness decreased. However, the AA content has no effect on molecular weights (Mw and Mn) and polydispersity (c.a. 1.5) of photoreactive cotelomers. The optimal AA content necessary to obtain a prepolymer with low volatile parts content and good PSA properties was determined.
A new method of solvent-free acrylic pressure-sensitive adhesives (PSAs) based on UV-induced cotelomerization products was presented. The key acrylic monomers (i.e., n-butyl acrylate and acrylic acid) with copolymerizable photoinitiator 4-acrylooxybenzophenone in the presence of a selected chain transfer agent (tetrabromomethane, TBM) were used in the UV-cotelomerization process. Moreover, two kinds of UV-photoinitiators (α-hydroxyalkylphenones, HPs and acylphosphine oxides, APOs) were tested. Photo-DSC, viscosity, thermogravimetric, and GPC measurements for cotelomers were performed. The kinetics study revealed that the systems with APOs, especially Omnirad 819 and Omnirad TPO, were characterized by a much higher reaction rate and greater initiation efficiency than HPs systems were. Additionally, the APO-based syrups exhibited a higher solid content (ca. 60–96 wt%), a higher dynamic viscosity (5–185 Pa·s), but slightly lower molecular weights (Mn and Mw) compared to HP syrups. However, better self-adhesive features (i.e., adhesion and tack) were observed for PSAs based on cotelomers syrups obtained using APOs with lower solid contents (55–80 wt%). It was found that as the solids content (i.e., monomers conversion) increased the adhesion, the tack and glass transition temperature decreased and the type and amount of photoinitiator had no effect on polydispersity. Most of the obtained PSAs were characterized by excellent cohesion, both at 20 °C and 70 °C.
New modifiers (i.e., acrylic syrups; ASs) of epoxy-resin-based thermally curable structural self-adhesive tapes (SATs) were prepared via a free radical bulk polymerization (FRBP) of n-butyl acrylate, butyl methacrylate, glycidyl methacrylate, and hydroxybutyl acrylate. In the process, two kinds of UV-photoinitiators (i.e., monoacylphosphine oxide/Omnirad TPO and bisacylphosphine oxide/Omnirad 819) and various mixing speed of the monomers mixture (200–1000 rpm) were applied. The TPO-based syrups exhibited a lower copolymers content (10–24 wt%), dynamic viscosity (<0.1 Pa·s), molecular weights (Mn and Mw, and polydispersity (1.9–2.5) than these with Omnirad 819. Additionally, the higher mixing speed significantly reduced monomers conversion and viscosity of ASs as well as molecular weights of the acrylate copolymers. These parameters influenced the properties of thermally uncured (e.g., adhesion) and thermally cured SATs (shear strength of aluminum/SAT/aluminum overlap joints). Better self-adhesive features were observed for SATs-TPO (based on ASs with lower monomers conversion, Mn and Mw); however, a slightly higher shear strength was noted for the thermally cured SAT-819 (ASs with higher monomers conversion, Mn and Mw). An impact of polydispersity of the acrylate copolymers as well as crosslinking degree of thermally cured SATs on the mechanical strength was also revealed.
Thermally curable pressure-sensitive structural adhesives tapes (SATs) were compounded using a solid epoxy resin and multifunctional acrylic telomer solutions (MATs) prepared by a thermally initiated telomerization process in an epoxy diluent containing two kinds of telogens (CBr4 or CBrCl3). Dynamic viscosity, K-value, and volatile mater content in MATs (i.e., MAT-T with CBr4, MAT-B with CBrCl3) were investigated in relation to telogen type and content. The influence of MATs on the self-adhesive features and curing behavior of UV-crosslinked tapes as well as on the shear strength of thermally cured aluminum–SAT–aluminum joints was investigated as well. Increasing the telogen dose (from 5 to 15 wt. parts) caused significant improvement in the adhesion (+315% and +184%), tack (+147% and +298%), and cohesion (+414% and +1716%) of SATs based on MAT-T and MAT-B, respectively. Additionally, MATs with high telogen content (especially the MAT-T-type) improved the resistance of cured joints to aviation fuel, humidity, and elevated temperature. The highest overlap shear strength values were registered for SATs based on MATs containing 7.5 wt. parts of CBr4 (16.7 MPa) or 10 wt. parts of CBrCl3 (15.3 MPa).
In this study, a novel and environmentally friendly method for the preparation of photoreactive pressure-sensitive adhesives (PSAs) was demonstrated. Adhesive binders based on n-butyl acrylate, methyl methacrylate, acrylic acid, and 4-acryloyloxy benzophenone were prepared with a UV-induced telomerization process in the presence of triethylsilane (TES) as a telogen and acylphosphine oxide (APO) as a radical photoinitiator. The influence of TES (0–10 wt. parts) and APO (0.05–0.1 wt. parts/100 wt. parts of monomer mixtures) concentrations on the UV telomerization process kinetics was investigated using a photodifferential scanning calorimetry method and selected physicochemical features of the obtained silicone-(met)acrylate telomeric syrups (K-value, solid content, glass-transition temperature, and dynamic viscosity), as well as properties of the obtained PSAs (Tg, adhesion, tack, and cohesion), were studied. An increase in TES content caused a significant decrease in the Tg values (approx. 10 °C) and K-value (up to approximately 25 a.u.) of the dry telomers, as well as the dynamic viscosity of the telomeric syrups. PSAs were obtained through UV irradiation of thin polymer films consisting only of silicone-(meth)acrylate telomer solutions (without the use of additional chemical modifiers or of a protective gas atmosphere and protective layers). PSAs were characterized by very good adhesion (12.4 N/25 mm), cohesion at 20 °C (>72 h) and 70 °C (>72 h), and low glass-transition temperature (−25 °C).
UV-cross-linkable and thermally curable self-adhesive structural tapes (SATs) were compounded using solid commercial benzoxazine resins (Araldite MT 35700 and Araldite MT 35910) and a photoreactive epoxyacrylate copolymer (EAC). As initiators of benzoxazine resin polymerization and epoxy component cationic polymerization, two kinds of latent curing agents (LCAs) were tested, i.e., amine type and ionic liquid type. The influence of the benzoxazine resin and the LCA type on the UV-cross-linking process, the self-adhesive features and thermal curing behavior of UV-cross-linked tapes, as well as the shear strength of cured aluminum/SAT/aluminum joints and thermal stability of adhesives were investigated. It was found that the amine additive and the benzoxazine resin take part in the UV-cross-linking process of the EAC as hydrogen donors, which is confirmed by an increase in cohesion (+86%) and a decrease in adhesion (−25%) of SATs. The highest results of adhesion to steel (47 N/25 mm) and overlap shear strength (11.1 MPa) values were registered for SATs based on Araldite MT 35910 and contained 7.5 wt. parts of the amine-type hardener. The formation of a polyacrylate-benzoxazine network has a significant impact on the course of the thermal curing process and the thermomechanical properties of adhesive joints, which was also confirmed by the Cure Index calculation.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.